• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.860-867
• /
• 2009

In this paper, we designed the array antenna for FMCW radar in X - band frequency, and we chose stacked structure for improvement of narrow bandwidth. The array antenna is implemented on the circuit board which is relative permittivity 2.33 and the stacked patchs are designed on the circuit board which is relative permittivity 4.6. A Foam which has a similar permittivity of air is added to keep the particular gap between array antenna and the stacked patch. The result of array antenna has characteristics that a half-power beam width is $10.6^{\circ}$ and antenna gain is 18.70 dBi and bandwidth is 1.25GHz at the design frequency of 9GHz. The result of the array antenna with the stacked structure has that the half power beam width is $15.17^{\circ}$ and the antenna gain is 15.85dBi and bandwidth is 2GHz. It is needed to improve the antenna gain as keeping bandwidth in same level.

• Journal of electromagnetic engineering and science
• /
• v.12 no.4
• /
• pp.234-239
• /
• 2012

This paper presents a compact K-band Doppler radar sensor for human vital signal detection that uses a radar configuration with only single coupler. The proposed radar front-end configuration can reduce the chip size and the additional RF power loss. The radar front-end IC is composed of a Lange coupler, VCO, and single balanced mixer. The oscillation frequency of the VCO is from 27.3 to 27.8 GHz. The phase noise of the VCO is -91.2 dBc/Hz at a 1 MHz offset frequency, and the output power is -4.8 dBm. The conversion gain of the mixer is about 11 dB. The chip size is $0.89{\times}1.47mm^2$. The compact Ka-band Doppler radar system was developed in order to demonstrate remote human vital signal detection. The radar system consists of a Ka-band Doppler radar module with a $2{\times}2$ patch array antenna, baseband signal conditioning block, DAQ system, and signal processing program. The front-end module size is $2.5{\times}2.5cm^2$. The proposed radar sensor can properly capture a human heartbeat and respiration rate at the distance of 50 cm.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.181-187
• /
• 2019

In this paper, we demonstrated a power amplifier monolithic microwave integrated circuit (MMIC) for X-band radar applications. It utilizes commercial $0.25{\mu}m$ GaN-based high electron mobility transistor (HEMT) technology and delivers more than 20 W of output power. The developed GaN-based power amplifier MMIC has small signal gain of over 22 dB and saturated output power of over 43.3 dBm (21.38 W) in a pulse operation mode with pulse width of $200{\mu}s$ and duty cycle of 4% over the entire band of 9 to 10 GHz. The chip dimensions are $3.5mm{\times}2.3mm$, generating the output power density of $2.71W/mm^2$. Its power added efficiency (PAE) is 42.6-50.7% in the frequency bandwidth from 9 to 10 GHz. The developed GaN-based power amplifier MMIC is expected to be applied in a variety of X-band radar applications.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.357-359
• /
• 2009

In this paper, the 2.4GHz doppler radar system consisting of the doppler radar module and a baseband module were designed to detect heartbeat and respiration signal without direct skin contact. A bio-radar system emits continuous RF signal of 2.4GHz toward human chest, and then detects the reflected signal so as to investigate cardiopulmonary activities. The heartbeat and respiration signals acquired from quadrature signal of the doppler radar system are applied to the pre-processing circuit, amplification circuit, and the offset circuit of the baseband module. ECG(electrocardiogram) and reference respiration signals are measured simultaneously to evaluate the doppler radar system. As a result, the respiration signal of doppler radar signal is detected to 1m without complex digital signal processing. The sensitivity and calculated from I/Q respiration signal were $98.29{\pm}1.79%$, $97.11{\pm}2.75%$, respectively, and positive predictivity were $98.11{\pm}1.45%$, $92.21{\pm}10.92%$, respectively. The sensitivity and positive predictivity calculated from phase and magnitude of the doppler radar were $95.17{\pm}5.33%$, $94.99{\pm}5.43%$, respectively. In this paper, we confirmed that noncontact real-time heartbeat and respiration detection using the doppler radar system has the possibility and limitation.

• Journal of electromagnetic engineering and science
• /
• v.16 no.3
• /
• pp.164-168
• /
• 2016

A dual-band through-the-wall imaging radar receiver for a frequency-modulated continuous-wave radar system was designed and fabricated. The operating frequency bands of the receiver are S-band (2-4 GHz) and X-band (8-12 GHz). If the target is behind a wall, wall-reflected waves are rejected by a reconfigurable $G_m-C$ high-pass filter. The filter is designed using a high-order admittance synthesis method, and consists of transconductor circuits and capacitors. The cutoff frequency of the filter can be tuned by changing the reference current. The receiver system is fabricated on a printed circuit board using commercial devices. Measurements show 44.3 dB gain and 3.7 dB noise figure for the S-band input, and 58 dB gain and 3.02 dB noise figure for the X-band input. The cutoff frequency of the filter can be tuned from 0.7 MHz to 2.4 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.386-398
• /
• 1998

In this paper, a high dynamic range IF logarithmic amplifier was designed and fabricated by the successive detection technique for radar systems. The fabricataed IF successive detection logarithmic amplifier(SDLA), a hybrid MIC type, achieves a logarithmic linearity of $\pm$1.4 dB and a dynamic range of 80 dB over 0.5 GHz to 1.5 GHz. The tangential signal sensitivity is -76 dBm, the NF is smaller than 5.5 dB, and the input VSWR is 2.0 : 1. This IF SDLA can be applied to radar systems by reducing the size and power consumption.

• ETRI Journal
• /
• v.41 no.2
• /
• pp.262-269
• /
• 2019

This paper introduces a low-cost, high-performance mmWave antenna array module at 77 GHz. Conventional waveguide transitions have been replaced by 3D CPW-microstrip transitions which are much simpler to realize. They are compatible with low-cost substrate fabrication processes, allowing easy integration of ICs in 3D multi-chip modules. An antenna array is designed and implemented using multilayer coupled-fed patch antenna technology. The proposed $16{\times}16$ array antenna has a fractional bandwidth of 8.4% (6.5 GHz) and a 23.6-dBi realized gain at 77 GHz.

• Journal of Aerospace System Engineering
• /
• v.4 no.3
• /
• pp.24-28
• /
• 2010

The purpose of this study is to define available microwave absorbing structure for aircraft from in the X-band(8.2~12.4GHz) frequencies. The electromagnetic wave absorption or shielding techniques is an important issue not only for military purpose but also for commercial purposes. Aircraft Radar Absorbing Structure(RAS) is absorbed or scattered propagation waves from the enemy radar. There are absorbing technologies at shaping design techniques and using Radar Absorbing Materials(RAM). RAM is more important because shaping design can't include perfect radar absorbing performance. In this study, based on material properties was introduced RAM and to analyze the each characteristics. Finally, we comparison appropriate RAM for aircraft.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.216-219
• /
• 2016

In this paper, the SIW(Substrate Integrated Waveguide)-based feeding antenna for the application of SDR(Software Defined Radar) is designed and manufactured. It is usually well-known that SIWs are easily integrated on PCB and have low transmission loss toward high powered input signal. Also, it is recommended that SIWs are strongly immunized to Electromagnetic Interferences(EMI). In particular, the manufactured antennas are loaded on the USRP(Universal Software Radio Peripheral) platform and employed to detect target RCS as an experiment in this paper. The operating frequency of the proposed antenna is in ISM(Industrial, Scientific and Medical) band(2.4~2.48 GHz) and the measured gain is over 8 dBi at 2.44 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.399-405
• /
• 2011

In this paper, we present the design of Q-band LC VCO and injection locking buffer for 77 GHz automotive radar sensor using 130 nm RF CMOS process. To improve the phase noise characteristic of LC tank, the transmission line is used. The negative resistance by the active device cross-coupled pair of buffer is used for high output power, with or without oscillation of buffer. The measured phase noise is -102 dBc/Hz at 1 MHz offset frequency and tuning range is 34.53~35.07 GHz. The output power is higher than 4.1 dBm over entire tuning range. The fabricated chip size is $510{\times}130\;um^2$. The power consumption of LC VCO is 10.8 mW and injection locking buffer is 50.4 mW from 1.2 V supply.