• 대한기계학회논문집A
• /
• 제25권2호
• /
• pp.220-227
• /
• 2001

The fatigue crack initiation life is studied on automotive tensile-shear spot weldment made from cold rolled carbon steel(SPC) sheet by using DCPDM and local strain approach. It can be found that the fatigue crack initiation behavior in spot weldment can be definitely detected by DCPDM system. To predict the fatigue life of spot weldment, the local stresses and strains at the potential critical region are estimated by approximate method based on Neubers rule and elastic-plastic FEM analysis. A satisfactory correlation between the predicted life obtained from Local strain approach based on Neubers rule and experimental life can be found in spot weldment within a factor of 2.

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.49-56
• /
• 1997

Effect of process parameters on the quality of condenser discharge weld for coated sheet steels was discussed. The welding specimens were coated with pure Zn of 20/20 g/m2 in the production line. Direct measurements of welding parameters such as the discharge current, the pressures and the voltage drop across the electrodes were carried out with welding process monitoring system. High speed camera was also utilized to analyze the weld formation process. Test results indicated that the relation between weld strength and applied energy was stabilized at the acceptable welding heat input range. It was thought that the acceptable welding heat input should be redefined based on the monitored data because the calculated value of the welding heat input could hardly be utilized if the discharge condition was changed. Mechanical test results and high speed photographs showed that expulsion deteriorated the weld quality and the strength at the same time especially when the size of the spatter was large enough to carry the molten metal, which should form the nugget, out of the welding spot. Results also demonstrated that the discharge current should be applied at the appropriate time during the process because sufficient nugget was not produced if the time was deviated from the optimum range.

• 한국레이저가공학회지
• /
• 제12권3호
• /
• pp.14-17
• /
• 2009

The laser welding was performed for the flange joint of two overlapped coaxial circular pipes which serve as the inlet and connector pipes of STS 316L. The laser welding test finally resulted in a good penetration depth of 1.8 to 2.0 mm. On the way to get the good welding quality, two important parameters were found to be optimized. One is the focal positioning which is the offset of the laser beam focus to the exact welding seam line, which is more critical in the inner flange laser welding. When the beam spot size was deviated more than $200\;{\mu}m$ from the seam line, welding of two pipes is failed. The other is a gap size since a certain amount of gap is inevitable due to fabrication tolerance, or artificial allowances for smooth insertion of a pipe. However, it is required to restrict the gap allowance within 0.2mm to avoid undesirable undercut on a welding bead.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.59-68
• /
• 1997

The modelling techniques of a center pillar-to-roof rail joint for low frequency vibration analysis are examined and some fundamental problems are addressed. To develop a simplified beam-spring model of the joint, the present work is focused on 1) practical shell modelling techniques and 2) joint spring stiffness estimation methods a practical model-updating method to match the calculated natural frequencies to the experimentally determine ones is proposed, particularly focusing on spot welding modelling. In joint spring modelling, the results from the model with one joint spring are compared with those from the model with three coupled springs. Finally, some fundamental problems in beam-spring modelling are addressed.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.176-184
• /
• 2003

New lubricant film of organic and inorganic composite resin was developed to improve the press formability of galvannealed steel sheets (GA) for automotive body panels. The frictional coefficient of lubricant GA steel sheets is about 20% superior to that of uncoated GA. The current range of spot welding of lubricant GA is similar to that of the uncoated GA, but the burning trace of spot welding is inferior to that of the uncoated GA in the oiling condition. The alkaline degreasability of lubricant GA shows 100% in alkaline degreasing condition of automotive company. The size and shape of the phosphated coating layer are similar to those of the uncoated GA sheet. The powdering property of the lubricant GA gives rise to 20∼50% improved property compared with the uncoated GA sheet.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.39-54
• /
• 1986

One of the important factors in practical welding situations is shunt effect which deteriorates weld quality due to a shunt current which flows in the exis- ting spot. Previously, this effect has not been analytically investigated, since the mechanism of shunt effect shows very complicated phenomena in the thermal and electrical behavior. In this paper this effect is extensively studied through theoretical and experimental analysis. The theoretical results obtained from a numerical analysis of the modelling of shunt effect are compared with experimental ones. Both results show good agreement and represent well the mechanism of shunt effect.

• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.33-39
• /
• 2002

The effect of out-of-plane loads on the fatigue strength of welded steel structures is examined through fatigue tests with weldment of two fillet weld joint types. The results of the fatigue tests are compared with those under axial loads, on the basis of the hot spot stress range at the weld toe. From the result of the comparison, a method on how to incorporate the effect of the out-of-plane bending stress is proposed using design S-N curves derived from fatigue tests under the axial load. The proposed method is useful for rational assessment of the fatigue strength of fillet-welded structures, where combined stresses of the in-plane axial stress and the out-of-plane bending stress are induced simultaneously due to the complexity of applied loads and structural geometry.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.112-117
• /
• 2001

The factor affecting on the fatigue strength of spot welded specimen have been studied. To analyze and predict crack initiation position and propagation directions on the spot welded area are very important for strength design of the automobile body structure. In fact, there are a various of loads in running automobile but, it is impossible to replay like an actual conditions in the laboratory. So, in this study tensile-shear type and in-plane bending type specimens were used in fatigue test and includes an analysis of fatigue crack initiation position and propagation directions about earth specimens. The results obtained in the present study are summarized as follows: 1. In tensile-shear type fatigue test, the region of fatigue crack initiation position was affected by out-of-plane bending deformation due to bending angle. 2 In in-plane bending type fatigue test, the behavior of fatigue crack initiation position and propagation derections due to angle between upper plate and lower plate was dominated by magnitude of in-plane bending moment.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.75-84
• /
• 2008

With the development of surface roughness textured steel for automotive body-in-white assemble, one of key issues is to understand the role of the surface roughness in textured steel sheets. To investigate effect of surface roughness on weldability in prepared steels, electrode force was varied. Steel sheets (T-H) with high surface roughness ($Ra\;=\;1.94\;{\mu}m$) reduced electrode life. It was attributed to the higher contact resistance at the electrode-sheet interface in the presence of the high surface roughness. The increased electrode diameter decreased current density, therefore reducing weld electrode life due to small weld button size. When an increased electrode force was used, a significant increase in the electrode life was observed in welding of high surface roughness steel sheet. This study suggested that contact resistance at the electrode-sheet interface was the dominant factor, as compared to the sheet-sheet interface for determining electrode life in welding of surface roughness textured steel.

• Journal of Welding and Joining
• /
• 제11권2호
• /
• pp.1-12
• /
• 1993

용접과 관련되는 분야에서, 재료평가와 비파괴 검사법으로서의 Acoustic Emission의 응용을 살펴 보았다. 재료 평가법으로서의 AE는 다른 시험방법들이 검출해 내지 못하는 재료 내부에서의 미시적인 현상들을 정량적으로 평가할 수 있는 장점을 가지고 있다. 앞으로 새로운 용접재료의 개발이라든지, 고도의 신뢰성이 요구되는 용접부위의 정량적인 평가를 위해서 AE의 응용은 중요한 정보들을 제공하게 될 것이다. 한편 용접구조물의 비파괴적 평가법으로서의 AE는 균열의 동적인 거동 및 균열의 위치를 검지할 수 있다는 장점 때문에 응용범위는 더욱 넓어질 것이다. 여기서 유의하여야 할 점은, 목적으로 하는 AE신호를 수만배 까지 증폭시키는 과정에서 환경잡음의 영향을 무시할 수 없는 경우에는 우선적으로 잡음을 적극적으로 제거하는 고도의 연구도 함께 병행되어야 한다는 것이다.