• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.2
• /
• pp.41-45
• /
• 2006

To get accurate positions of GPS antennas, one should apply phase center variations (PCV) corrections in the data processing. Until recently, relative calibrations, originally proposed by National Geodetic Survey of United States, were the international standard. However, in late 2006, International GNSS Service will switch to absolute calibration methods. In this study, we compared the position differences caused by different PCV models, and their effects on the calculations of Precipitable Water Vapor (PWV) in the atmosphere. Data from ${\sim}40$ permanent GPS stations in Korea were processed and we found that the vertical position differences reach up to 5 cm, depending on the model selected. Also the PWV values varied quite significantly: the maximum bias in the computed PWV values was ${\sim}4$ mm.

• 대한전기학회논문지:전력기술부문A
• /
• 제50권4호
• /
• pp.157-165
• /
• 2001

The two criteria to identify the disturbances of the power transformer has been reported in this paper. They have been derived through EMTP simulations of internal faults, inrush and overexcitation for the model of 154/22.9[kV], 40[MVA], Y-Y three-phase power transformer. We propose the crisp algorithm which uses two criteria. A series of test results clearly indicate that the method can identify not only an internal fault but also the other transients. The average of relay operation times is about 7.2[ms]. The proposed algorithm immunes to the transient state.

• 대한산업공학회지
• /
• 제27권2호
• /
• pp.169-175
• /
• 2001

Most of studies on automated storage/retrieval (AS/R) system assumed that storage capacity is given, although it is a very important decision variable in the design phase. We propose a simple algorithm to estimate the required storage capacity, i.e., number of aisles and number of openings in vertical and horizontal directions in each aisle, of an AS/R system under stochastic demand, in which storage requests occur endogenously and exogenously while the retrieval requests occur endogenously from the machines. Two design criteria, maximum permissible overflow probability and maximum allowable storage/retrieval (S/R) machine utilization, are used to compute the storage capacity. This model can be effectively used in the design phase of new AS/R systems.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1999년도 추계학술대회논문집
• /
• pp.83-90
• /
• 1999

Centralized safety stock in a periodic replenishment system which consists of one central warehouse and m regional warehouse can reduce backorders allocation the centralized safety stocks to regional warehouse in a certain instant of each replenishment cycle. If the central warehouse can not monitoring inventories in the regional warehouse, then we have to predetermine the instant of allocation according to demand distribution and this instant must be same for all different replenishment cycle. However, transition of inventory level in each cycle need not to be same, and therefore different instant of the allocation may results reduced shortage compare to the predetermined instant of allocation. In this research, we construct a dynamic model based on the assumption of monitoring inventories inventories in the regional warehouse everyday, and develop an algorithm minimize shortage in each replenishment cycle using dynamic programming approach.

• 전력전자학회논문지
• /
• 제12권2호
• /
• pp.123-130
• /
• 2007

본 논문에서는 불연속 인덕터 전류모드에서의 다상 교호 강압 컨버터의 정상상태 해석 및 소신호 모델을 유도하여 일반화된 식을 제시한다. 컨버터의 제어기 설계를 위해서 필요한 완전한 차수 모델을 통한 소신호 모델의 전달함수를 유도하고 이를 통해 시스템의 동특성을 분석한다. 시뮬레이션 및 실험 결과를 통하여 이론에서 제시한 특성을 검증한다.

• 한국멀티미디어학회논문지
• /
• 제11권6호
• /
• pp.891-902
• /
• 2008

The software once developed enters in to the $2^{nd}$ phase of its useful operational life, where it performs its functions for which it has been developed. This is an important phase of software life, wherein the developers and users have to assess the performance of the software to prolong its operational life with efficiency, effectiveness and economy. Performance of the software is based on the measurement of the quality characteristics to ascertain that it is meeting or exceeding the needs of customers in terms of its functionality, usability, efficiency, reliability, availability, maintainability, portability etc. These software quality attributes defined under ISO 9126 provide an overall good framework for assessing the performance of the software. This paper describes a Software Performance Assessment (SPA) model using the Goal-Question-Metric (GQM) paradigm which has been applied to the operational software in real context with successful results.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권4호
• /
• pp.478-486
• /
• 1995

Cu/NbTi multilayer thin films and superconducting wires were fabricated and heat treated with conventional annealing and analyzed by differential scanning calorimetry (DSC) as a basic study for the enhancement of Jc. Interfacial reactions of Cu/NbTi multilayer thin films and superconducting wires were investigated with optical microscope, SEM, and XRD. According to the effective heat of formation (EHF) model, CU$\_$3/Ti was predicted as a first phase. However, considering the crystalline structure and thermodynamics, CuTi was predicted as a first phase. According to the results of DSC and XRD, CU$\_$2/Ti was found to be the first phase, followed by the formation Of CU$\_$4/Ti. The difference in first crystalline phase between the experimental result and the predicted one was discussed. In case of Cu/NbTi superconducting wires, the compounds formed at the Cu/NbTi interface grew with annealing time and the amount of compounds formed in Nb-47wt%Ti alloy was larger than that in Nb-50wt%Ti alloy. It seemed that the incubation time for the formation of compounds in Nb-50wt%Ti alloy was longer than that formed in Nb-47wt%Ti alloy. Also, the diffusion was the rate controlling step for the growth of compounds in all specimens. These compounds were formed at 500-600.deg. C for I hour annealing and, thus, the drawing time below I hour must be required to minimize the growth of compounds for the enhancement of Jc.

• 대한기계학회논문집B
• /
• 제23권10호
• /
• pp.1327-1339
• /
• 1999

Characteristics of two-phase flow and heat transfer were numerically investigated in a submerged gas Injection system. Effects of both the gas flow rate and bubble size were investigated. In addition, heat transfer characteristic and effects of heat transfer were investigated when temperature of the injected gas was different from that of the liquid. The Eulerian approach was used for the formulation of both the continuous and the dispersed phases. The turbulence in the liquid phase was modeled by the use of the standard $k-{\varepsilon}$ turbulence model. The interphase friction and heat transfer coefficient were calculated by means of correlations available in the literature. The turbulent dispersion of the phases was modeled by introducing a "dispersion Prandtl number". The plume region and the axial velocities are increased with increases in the gas flow rate and with decreases in the bubble diameter. The turbulent flow field grows stronger with the increases in the gas flow rate and with the decreases in the bubble diameter. In case that the heat transfer between the liquid and the gas is considered, the axial and the radial velocities are decreased in comparison with the case that there is no temperature difference between the liquid and the gas when the temperature of the injected gas is higher than the mean liquid temperature. The results in the present research are of interest in the design and the operation of a wide variety of material and chemical processes.

• 농업과학연구
• /
• 제23권2호
• /
• pp.272-284
• /
• 1996

The present study has quantitatively assessed the regional production, income and employment impact resulting from the construction and operation of nuclear power plant (NPP) upon the domestic local areas by applying the regional input-output analysis model to the case of Wolsong unit-l site. The conclusions regarding the most likely regional economic impacts upon the wolsong site are summarized as follows: 1. The income multipliers are calculated to be 1.563 for the construction phase and 1.500 for the operation phase. These values are relatively high compared with those of other conventional facilities. 2. The level of total employee's wage induced employment associated with the construction phase has been estimated to be 37,000 while that with the operational phase in 1990 to be 5,610. 3. With relation to the aspect of resident welfare it is found that the industrial sector associated with electricity, gas and water supply have remarkably improved with the construction of the NPP. 4. The NPP siting has induced substantial changes in interindustry (input-output) structures of the Wolsong unit-l site which is one of the rural areas where all the domestic NPPs are sited. Such changes are attributed to the industrial recomposition of the region. 5. With the application of other regional economic analysis models and the use of more sufficient regional data, other detailed studies on the economic impact analysis of domestic NPP-related facility sitings are suggested to be carried out further since the influence of NPP sitings is significant to the national economic impact as well as the regional economic impact.

• 한국전자파학회논문지
• /
• 제29권2호
• /
• pp.109-117
• /
• 2018

비선형적으로 회전하는 표적의 inverse synthetic aperture radar(ISAR) 영상을 형성하기 위해서는 표적의 수신 신호에 적절한 회전운동 보상기법을 수행해 주어야 한다. 대표적인 회전운동 보상기법인 prominent point processing(PPP)은 산란점의 위상정보를 이용하여 비선형 회전성분을 선형화하는 기법이다. 본 논문에서는 integrated cubic phase function(ICPF)을 이용하여 산란점의 위상정보를 추정한 다음 PPP를 수행하여 ISAR 영상을 형성하는 방법을 제안한다. ICPF는 다수의 산란점으로부터 중첩된 신호가 수신되었을 때 1차원 영역(domain)의 최댓값을 찾는 작업을 수행함으로써 산란점의 위상정보를 추정할 수 있다. 시뮬레이션 결과 ICPF를 이용한 산란점 위상정보 추정 후 PPP를 수행함으로써 지배적 산란점이 존재하지 않는 환경에서 실시간으로 높은 품질의 ISAR 영상을 획득하였다.