• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.2
• /
• pp.87-96
• /
• 2012

With a view to determine a safe speed the limit of a manipulator arm, several experiments was performed with a multi-jointed manipulator in maintenance and decommissioning tasks of nuclear facilities. Under the simulated emergency conditions, which were generated with random combinations of manipulator arm speed, failure probability and failure type, response characteristics of human operators to various malfunctions of a manipulator arm were measured in terms of reaction time, number of false alarm, and number of misses. This paper demonstrated that failure type, manipulator axes and manipulator arm speed has significant effects on human reaction time. As a whole the reaction time was slightly increased with manipulator arm speed, which is showed somewhat different pattern due to failure type. The reaction time to an axis acting on a workpiece directly, which could flex and extend, was fastest and much more its standard deviation was small. Various factors which may affect safe speed were also described.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.60-67
• /
• 2011

In this paper, the structure of a gravity compensator(GC) was studied, and the 6-axis robot manipulator which is newly developed by applying the GC is presented to improve the torque performance and repeatability error of the robot joint. The kinematics analysis on the robot was presented. Also, experiments of the performance of the joint actuator of robot adopting the gravity compensator were presented by the GC to $1^{st}$ and $2^{nd}$ joints of the robot arm. According to the experiment results, it was validated that the position errors and load torque of the robot joint actuator adopting the GC are reduced significantly.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.775-778
• /
• 2002

In this paper, we've studied multi axis control system using embedded web server which is controlling and monitoring the state data of moors. NanoWit2 Board has been ported Linux Operating System and fabricated Web Sorrel by GCC. Motion controller is used MCS-40 of e-MOTION Tek Co., Ltd. which receiving control signal, controlling motors and sending the state data to Web Server.

• Journal of the Ergonomics Society of Korea
• /
• v.19 no.2
• /
• pp.75-86
• /
• 2000

In this study, the characteristics of transmitted vibration on HAS(hand-arm system) were identified to evaluate physical load due to the work surface orientation, tool weight and push force during powered drilling tasks. The characteristics of transmitted vibration on work surface orientation showed that the acceleration of transmitted vibration on horizontal work surface was higher than that on the vertical work surface. Regarding the characteristics of transmitted vibration on tool weight, the vibration acceleration level becomes lower as the tool weight becomes heavier. The amount of transmitted vibration on hand-arm system was decreased down to the tool weight of 2.4kg. However, as the tool weight becomes heavier than 2.8kg, the amount of transmitted vibration was increased and had peak value at 3.2kg of tool weight. Regarding the characteristics of transmitted vibration on push force, the vibration acceleration level goes higher, as the push force becomes larger. The characteristics of transmitted vibration on the axis of vibration showed that the direction of $Z_h$ had the highest acceleration compared to the direction of $X_h$, and $Y_h$. The direction of $X_h$, $Y_h$ and $Z_h$ had the highest acceleration of transmitted vibration on the hand, wrist and elbow, respectively. The results of this study showed that the condition which affect the lowest physical load to the subject on the powered drilling task would be working with the 2.4kg of tool weight on the vertical work surface.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.3
• /
• pp.34-40
• /
• 2001

Robot manipulator has highly nonlinear dynamics. Therefore the control of multi-link robot arms is a challenging and difficult problem. In this paper a decentralized adaptive fuzzy sliding mode scheme is developed for control of robot manipulators. The proposed scheme does not require an accurate manipulator dynamic model, yet it guarantees asymptotic trajectory tracking despite gross robot parameter variations. Numerical simulation for decentralized control of a 3-axis PUMA arm will also be included.

• Advances in robotics research
• /
• v.2 no.2
• /
• pp.113-127
• /
• 2018

Robotics and automation are rapidly growing in the industries replacing human labor. The idea of robots replacing humans is positively influencing the business thereby increasing its scope of research. This paper discusses the development of an experimental platform controlled by a robotic arm through Robot Operating System (ROS). ROS is an open source platform over an existing operating system providing various types of robots with advanced capabilities from an operating system to low-level control. We aim in this work to control a 7-DOF manipulator arm (Robai Cyton Gamma 300) equipped with an external vision camera system through ROS and demonstrate the task of balancing a ball on a plate-type end effector. In order to perform feedback control of the balancing task, the ball is designed to be tracked using a camera (Sony PlayStation Eye) through a tracking algorithm written in C++ using OpenCV libraries. The joint actuators of the robot are servo motors (Dynamixel) and these motors are directly controlled through a low-level control algorithm. To simplify the control, the system is modeled such that the plate has two-axis linearized motion. The developed system along with the proposed approaches could be used for more complicated tasks requiring more number of joint control as well as for a testbed for students to learn ROS with control theories in robotics.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.163-168
• /
• 2001

A manipulator for test-cup attachment modules, which was a part of a robot milking system, was developed to reduce cost and labor for cow milking processing. A Cartesian coordinate manipulator was designed for the milking process, because it was quite flexible and can be constructed more economically than any other configuration. The manipulator was made use of DC motors, screws for power transmission, a RS422 interface system for the transmission of coordinate values and a one-chip microprocessor, 89C52. Performance tests of the manipulator were conducted to measure experimentally the precision of all axes. Some of the results are as follows. 1. The Cartesian coordinate manipulator was designed and built. Dimension of the three perpendicular axes (X, Y, and Z) and one arm’s axis(W) to pick up and transfer the modules were 700㎜$\times$450㎜$\times$550㎜$\times$650㎜. The arm’s axis moved the teat-cup attachment module, which attached four teat-cup to four teats, detached four teat-cup from four teats, was designed and manufactured by using CAD, CAM and CNC. 3. After 10 replications of exercising the manipulator, mean precision values(positioning error) of X, Y, Z axes wee 0.48㎜, 0.20㎜, 0.19㎜, respectively. Therefore, we conclude the axes to have a precision better than 0.5㎜, had no problem to operate correctly the milking manipulator.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.4
• /
• pp.397-402
• /
• 2013

In this study, we carried out the each lines of section, using GC (green silicon carbide) whetstone, the SCM415 material which separated by after and before heat treatments process, in 3+2 axis machining centers for integrated grinding after cutting end mill works, the spindle speed 8000 rpm and feed rate 150 mm/min. For the analysis of the centerline average roughness (Ra), we measured by 10 steps stages. Using Finite element analysis, we found the result of the load analysis effect of the assembly parts, when applied the 11 kg's load on both side of the ATC (Automatic tool change) arm. The result is as follows. For the centerline average roughness (Ra) in the non-heat treatment work pieces, are appeared the most favorable in the tenth section are $0.510{\mu}m$, that were shown in the near the straight line section which is the smallest deformation of curve. In addition, the bad surface roughness appears on the path is to long by changing angle, the more inclined depth of cut, because the chip discharging is not smoothly.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.277-285
• /
• 2004

In this paper, a 2 DOF haptic yawing joystick for use as the navigation input device in virtual environments is introduced. The haptic yawing joystick has 360° range for yawing motion and ±100° for pitching motion. The device can support weights of up to 26N for χ axis and 10N for axis with 10kHz of sampling rate. The size of the haptic yawing joystick is so small that it can be assembled on armrest of an arm chair and has relatively larger work space than other conventional 2 DOF joysticks. For the haptic yawing joystick, an ellipse navigation algorithm using the user's velocity in the virtual navigation is proposed. The ellipse represents the velocity of the user. According to the velocity of the navigator, the ellipse size is supposed to be changed. Since the path width of navigation environments is limited, the ellipse size is also limited. The ellipse navigation algorithm is tested in 2 dimensional virtual environments. The test results show that the average velocity of the navigation with the algorithm is faster than the average navigation velocity without the algorithm.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.154-161
• /
• 2009

In order to implement continuous-path motion on a robot, it is necessary to blend one joint motion to another joint motion near a via point in a trapezoidal form of joint velocity. First, the velocity superposition using parametric interpolation is proposed. Hybrid motion blending is defined as the blending of different two type's motions such as blending of joint motion with linear motion, in the neighborhood of a via point. Second, hybrid motion blending algorithm is proposed based on velocity superposition using parametric interpolation. By using a 3-axis SCARA (Selective Compliance Assembly Robot Arm) robot with $LabVIEW^{(R)}$ $controller^{(1)}$, the velocity superposition algorithm using parametric interpolation is shown to result in less vibration, compared with PTP(Point- To-Point) motion and Kim's algorithm. Moreover, the hybrid motion $algorithm^{(2)}$ is implemented on the robot using $LabVIEW^{(R)(1)}$ programming, which is confirmed by showing the end-effector path of joint-linear hybrid motion.