• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.845-851
• /
• 2013

In this paper, a robust optimization approach is applied to the two-axes stage using a piezoelectric actuator for precise motion tracking. Robust control is based on LQG/LTR (linear quadratic Gaussian control with loop transfer recovery) control. Further, an LMI (linear matrix inequality) is used to find the optimal parameter in the loop transfer recovery step, instead of a trial and error method. A decoupler in the shape of FIR filter is added to reduce the coupling effect between the motions of the two axes, and hence, the feedback control loop is designed independently for each axis motion. The experimental result shows that the proposed control scheme can be applied effectively for motion control of the two-axes stage.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.71-81
• /
• 2000

This paper describers a look ahead algorithm of PC-NC(personal computer numerical control). The algorithm is based on acceleration/deceleration before interpolation which doesn\`t include a command error and determines a feedrate value at the end point of each block(or start point of each block). The algorithm is represented as following; 1) calculating two maximum arrival feedrates(F$_1$,F$_2$) by an acceleration value, a command feedrate, and the distance of a NC block, 2) getting a tangent feedrate (F$_3$) of the adjacent blocks, 3) choosing a minimum value among these three feedrates, and 4) setting the value to a feedrate of a start point of the next block(or a end point of the previous block). The proposed look ahead algorithm was implemented and tested by using a commercial TROS(real time operation system) on the MS-Windows NT 4.0 in a PC platform. For interfacing to a machine, a counter board, a DAC board and a DIO board were used. The result of the algorithm increased a machining precision and a machining speed in many short blocks.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.406-409
• /
• 1997

An economical 4-axis CNC controller employing step motors is designed and implemented in this paper. By using the inherent ability of holding position of the motor, the CNC controller uses open-loop control for removing trajectory error and for a simple hardware. Each drive of axis has an 8-bit microprocessor 89C52 and a PC controls the axes and pendant by means of RS232C serial communication. Backlash is also compensated at the axis controller. While compensating the backlash, the feed rate becomes zero in order to minimize trajectory error. The trajectories of 16ms interval are computed on PC and are sent to motor drives. In the drives, the trajectories are linearly interpolated for 2ms interval. The developed CNC does not require add-on specific motion card on PC. From the experimental results, the validity of the CNC controller based on step motor is proved.

• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.654-667
• /
• 2003

This paper presents a consequence of the systematic approach to identify the aerodynamic parameters of an unmanned aerial vehicle (UAV) equipped with the automatic flight control system. A 3-2-1-1 excitation is applied for the longitudinal mode while a multi-step input is applied for lateral/directional excitation. Optimal time step for excitation is sought to provide the broad input bandwidth. A fully automated programmed flight test method provides high-quality flight data for system identification using the flight control computer with longitudinal and lateral/directional autopilots, which enable the separation of each motion during the flight test. The accuracy of the longitudinal system identification is improved by an additional use of the closed-loop flight test data. A constrained optimization scheme is applied to estimate the aerodynamic coefficients that best describe the time response of the vehicle. An appropriate weighting function is introduced to balance the flight modes. As a result, concurrent system models are obtained for a wide envelope of both longitudinal and lateral/directional flight maneuvers while maintaining the physical meanings of each parameter.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.35-44
• /
• 2009

Long stroke Fast Tool Servo (LFTS) with maximum stroke of $432{\mu}m$ is designed, manufactured and tested for fabrication of optical free-form surfaces. The large amount of stroke in LFTS has been realized by utilizing the hinge and lever mechanisms which enable the displacement amplification ratio of 4.3. In this mechanism the peculiar shape was devised for maximizing the displacement of end tip in LFTS and special mechanical spring has been mounted to provide the sufficient preload to the piezoelectric actuator. Also, its longitudinal motion of tool tip can be measured by capacitive type displacement sensor and closed-loop controlled to overcome the nonlinear hysteresis. In order to verify the static and dynamic characteristics of designed LFTS, several features including step response, frequency response and cut-off frequency in closed-loop mode were experimentally examined. Also, basic machining result shows that the proposed LFTS is capable of generating the optical free-form surface as an additional axis in diamond turning machine.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.10
• /
• pp.2236-2245
• /
• 1997

The DBS system is being highlighted as actual area for the information societics. Specially, the DBS have been proposed very useful system to access the broading service in more widely sea. But the antenna tracking system for maritime DBS receiving is requried complicated control system because of the those complex motion represented pitching, rolling and yowing etc. Our resesrch target is a development of tracking system to the KOREASEA(MUGUNGWHA-1,2) for the applicated small size shipping. So our development focus was concentrated the two development direction. The first focus was represented low-cost system for popularization of small-size shipping around sea of the Korea peninsula. The second focus was an adaptive possibilities with domestic eqdupiment which was developed satellite receiving for KOREASAT. The anntenna mount is designed a compact size and easy operation use to the Az/El 2-axis type which is operated by step motor. And this mount type is very useful on a ship in the near sea of Korea peninsula. Basic tracking method is used th step-tracking algorithm, and the ship's moving compensation is adapted to the closed loop control method by ship's moving detection of gyro sensor. Control part is consists of converter, countertime, VCO, micro-computer and it's software. Testing the operation by the ship's moving simulator, and algorithm is designed tracking and moving compensation by receiving state.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.252-257
• /
• 2000

This paper describes a look-ahead algorithm of PCNC(personal computer numerical control). The algorithm is based on acceleration/deceleration before interpolation never including a command error and determines a velocity value in end point of each block(or start point of each block). The algorithm is represented as following; 1) calculating two maximum arrival velocity(v1, v2) by a acceleration value, a command velocity and distance in a previous block and a next block, 2) getting a tangent velocity(v3) of the adjacent blocks, 3) choosing a minimum value among these three velocities, and 4) setting the value to a velocity of a start point of the next block(or a end point of the previous block). The proposed look-ahead algorithm was implemented and tested by using a commercial RTOS(real time operation system) on the MS-Windows NT 4.0 in a PC platform. For interfacing to a machine, a counter board, a DAC board and a DIO board were used. The result of the algorithm increased a machining precision and a machining speed in many short blocks.