• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.32-39
• /
• 1997

The coiling station of ISP coil box is an equipment that winds a hot bar rolled at reduction unit into a coil without mandrel. In the coiling process, the roll gap of the bending unit is a significant one of several factors that influence bar coiling. To obtain a good bar-coil, the roll gap must be set appropriately according to the bar thickness. In this study, with 2-dimensional isothermal elastic-plastic finite element method, authors investigated influence of the change of the roll gap on the initial coiling shapes and the formed inner diameters of coils. Based on finite element analysis, authors proposed the appropriate roll gap according to the bar thickness to be able to wind a hot bar. The inner diameters of coils by results of analysis comparatively agreed with coling operation conducted in plant.

• 소성∙가공
• /
• 제25권2호
• /
• pp.116-123
• /
• 2016

Press-brake bending is used to shape flat and thick plates into a targeted circular configuration without excessive localized thinning or thickening. A brake bending press called 'a knife press bending apparatus' has been widely adopted to manufacture thick, large and long pipe from initially thick plate. Submerged Arc Welded (SAW) pipes are also produced by employing press-brake bending. These pipes are mainly used for oil, natural gas and water pipelines. The principal process variables for press-brake bending can be summarized as stroke of the press-brake knife, the distance between both roll in the lower die, and the feeding length of the plate. Many combinations of these process variables are available, thus various pipe diameters can be realized. In the current study, a series of repetitive numerical simulations by feeding a thick plate with initial thickness of 25.4mm were conducted with the consideration of elastic recovery. Furthermore, an index for SAW pipe production is proposed which can be widely used in industry.

• 대한기계학회논문집A
• /
• 제31권8호
• /
• pp.847-854
• /
• 2007

The battery electrode of a mobile phone is made of layered polymer coated on aluminum foils and the hot rolling process is applied to increase the density per volume of an electrode for a high capacity battery. The flatness of batteries surfaces should be less than $2{\mu}m$. To satisfy the required flatness, the deformation of roll surface due to bending and heating of the roll should be minimized. Complicated hot oil paths of $100^{\circ}C$ inside the roll are required for heating the polymer layers. FEA was used to calculate thermal deformations and temperatures distributions of the roller. Based on FEA, a modified surface curvature called a crown roll was suggested and this gave the area of 30% improved flatness compared with a flat roll. The flat roll satisfied the flatness of $2{\mu}m$ in the length of 340 mm and the crown roll resulted in the longer length of 460 mm. Experiments to measure the temperature distribution and thermal strain were performed and compared with FEA. There were only 6% difference between two results.

• 소성∙가공
• /
• 제6권2호
• /
• pp.118-135
• /
• 1997

In order to analyze the deformation and residual curvature of steel sheets in the strip processing lines, a program for calculating curvature and work hardening of sheet was developed. Strip deformation caused by repeated bending under tension in the process lines was analyzed on the basis of the incremental-plasticity theory with the mixed hardenting model for the purpose of predicting the strip shape and the yield stress change. The developed calculation program was applied to predict curl and gutter of sheets within a 10% difference. The yield stress increment was also predicted with the similar accuracy. Application of the model to tension legvelling process showed that gutter could be controlled by intermesh and elongation. The yield stress increment in the electro-galvanizing line calculated by the developed program was found to be dependent on the yield strength, the applied tension and the diameter of the smallest roll.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.702-705
• /
• 2005

Metallic sandwich plates with Inner dimpled shell subjected to 3-point bending have been analyzed and then optimized for minimum weight. Inner dimpled shells can be easily fabricated by press or roll with high quality precision and bonded with same material skin sheets by resistance welding or adhesive bonding process. Optimized shape of inner dimple is a hemispherical shell to minimize weight without failure, including face yielding, face buckling and inner dimple buckling. It is demonstrated that bending stiffness of sandwich plate is 2 or 3 times than solid plates with same strength

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• 한국산학기술학회논문지
• /
• 제16권10호
• /
• pp.6977-6984
• /
• 2015

품질 향상을 위해 연속적인 소성 변형을 이용한 롤 포밍 공정에 피어싱, 벤딩, 트리밍 등 별도의 가공공정을 통합한 볼 슬라이드 레일의 멀티 롤 포밍 공정의 필요성이 대두되고 있다. 하지만 프레스기의 진동 및 소음은 이 공정에서 생산되는 슬라이드 레일의 품질 저하를 유발한다. 본 연구에서는 롤 포밍 유한요소 프로그램으로 최적 변형률을 고려하여 롤을 설계하였다. 그리고 멀티 공정의 정적 안정성을 예측하기 위해 구조해석 프로그램으로 프레스기에 대한 응력 및 변형량을 계산하였다. 또한 공진영역에서의 장치들의 운전을 회피하기 위해 Modal 해석을 통해 1, 2차 모드에서의 고유진동수를 계산하였다. 그 결과 공정의 동적 안정성 개선을 확인하기 위해 마이크로폰과 가속도계를 이용하여 기존 및 연구 공정들의 소음, 진동의 크기를 비교하였다. 그리고 기존 및 연구 공정으로 생산되어진 레일의 폭 치수와 표면거칠기를 측정하였다. 따라서 해석 및 실험적 연구를 통해 멀티 롤 포밍 공정이 안정하다는 것을 알 수 있었다.

• 한국정밀공학회지
• /
• 제33권2호
• /
• pp.115-119
• /
• 2016

Winding is one of the major processes in roll-to-roll systems. Taper tension profile in a winding determines the distribution of stress in the radial direction, i.e., the radial stress in the wound rolls. Maximum radial stress is major cause of material defect, and this study has been actively proceeded. Traditional models of radial stress model were focused on flexible and light substrate. In this study, we developed an advanced radial stress model including effects of both these parameters(weight and stiffness) on the radial stress. The accuracy of the developed model was verified through FEM(Finite Element Method) analysis. FEM result of maximum radial stress value corresponds to 99 % in comparison to result with the model. From this study, the material defects does not occur when the steel winding. And steel industry can be applied to improve the winding process.

• 소성∙가공
• /
• 제11권2호
• /
• pp.147-154
• /
• 2002

The tension levelling Process is Performed to elongate the strip plastically In combination of tensile and bending strain so that all longitudinal fibers In the strip have an approximately equal amount ofn length and undesirable strip shapes are corrected to the flat shape. Thus paper is concerned with a simulation of the tension levelling process based on the analysis of tile unit model for the tension leveller. Analysis technique such as the sequential analysis of the unit model is suggested and verified with the assembly analysis of the unit model for the effective arts economic analysis of the full set of the tension leveller. Analysis of the full tension levelling Process using sequential unit models Is carried out for steel strips with the shape defect and provides the effect of the intermesh and optimum amount of the intermesh in tension levelling process.

• 소성∙가공
• /
• 제11권2호
• /
• pp.138-146
• /
• 2002

This paper is concerned with the simulation-based process design method involved non-steady state problem of tension levelling considering the elasto-plastic hardening behavior of a metallic strip by a commercial code ABAQUS/Standard. The tension levelling process is peformed to elongate the strip plastically in combination of tensile and bending strain by a controlled manner so that all longitudinal fibers in the strip have an approximately equal amount of length and undesirable strip shapes are corrected to the flat share. Objectives of this paper are the development of a general method for the design of a tension leveller by a finite element method and parameter studies for the deisgn variables such as the applied tension, the roll intermash includes the determination of the steady state using the simple unit of the tension levelling line and the effect of the finite element mesh size on the amount and distribution of the strain calculated. The analysis provides the information about the intermesh effect on the amount and final shapes of the strip and distribution of the strain in order to determine the amount elongation for correction of the irregular share.