• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.695-701
• /
• 2018

Research into exhaust heat recovery has been actively carried out to improve the thermal efficiency of internal combustion engines. In this study, the performance of thermoelectric generation from exhaust heat recovery for motorcycle engines was analyzed by 1-D thermo-fluid simulation. GT-SUITE, which was developed by Gamma Tech., was used for the simulation of the internal combustion engine and thermoelectric generation system. The basic performance of the engine was analyzed in the range of engine speed of 1000~7000 rpm and engine load of 0~100%. The ratio of exhaust heat energy to fuel chemical energy was found to be about 40~60%. A combined simulation of the engine model and thermoelectric generation model was carried out to analyze the voltage, current and power generated by the thermoelectric material. The generation characteristics of the thermoelectric material was dominantly affected by the exhaust gas temperature. The maximum generated power of the current thermoelectric generation system was found to be about 2.2% of the total exhaust heat energy. The design optimization of the thermoelectric generation system will be carried out to maximize its power generation and economic feasibility.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.22-28
• /
• 2009

열역학 제 2법칙의 관점의 열역학적 가용에너지인 엑서지 해석법을 적용하여 가솔린, 메탄올, M90 연료를 사용한 전기점화 기관의 성능해석을 수행하였다. 열역학적 사이클 해석을 위하여 사이클을 구성하는 각 과정은 열역학적 모델로 단순화하였고, 크랭크 각도에 따른 실린더의 압력과 작동유체를 구성하는 연료, 공기 및 연소생성물의 열역학적 물성 값들을 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였다. 실험데이터는 단기통 전기점화기관을 가솔린, 메탄올과 M90(메탄을 90%+부탄 10%의 혼합연료)을 연료로 WOT(Wide Open Throttle), MBT(Minimum advanced spark timing for Best Torque), 2500rpm 조건으로 운전하여 측정하였다. 계산에 이용한 자료는 실험으로 측정한 크랭크 각도에 따른 연소실의 압력, 흡입공기와 연료유량, 흡입공기 온도, 냉각수 온도와 배출가스 온도 등이다. 이를 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였으며 각 과정에서의 손실 일은 연소과정에서 가장 크며 팽창과정, 배출과정, 압축과정 및 흡입과정 순으로 크게 나타났다.

• Composites Research
• /
• v.16 no.1
• /
• pp.1-12
• /
• 2003

This study developed SiC$_{p}$/A1$_2$O$_3$$_{f}$/Al composites for electronic packaging to which reinforcements were added with the volume fractions of 49%, 56% and 63% by the squeeze casting method. 0.8 wt. % of the inorganic binder as well as the A1$_2$O$_3$ fiber and SiC Particles with the volume fraction of 1:10 were added to the composites, which were produced in the newly designed mold. For the produced SiC/Al composites, the CTEs (coefficients of thermal expansion) were measured from 30 to 300 and compared with the FEM numerical simulation to analyze the temperature dependent properties. The experiment showed the CTEs of SiC$_{p}$/A1$_2$O$_3$$_{f}$/Al composites that were intermediate values of those of Rule of Mixture and Turner's Model. The CTEs were close to Turner's Model in the room temperature and approached the Rule of Mixture as the temperature increases. These properties analyzed from the difference of the average stress acting between the matrix and the reinforcements proposed in this study.

• Journal of Bio-Environment Control
• /
• v.19 no.3
• /
• pp.123-129
• /
• 2010

A study on modeling of medium temperature drops of the elevated-bench hydroponic system for strawberry cultivation during low temperature season was conducted. Four different conditions were used for the experiment. These consisted of two kinds of bed types (plant, V), four kinds of medium (rice, perlite, rice hulls80% and peatmoss20%, perlite80% and peatmoss20%), two kinds of mulched bed (mulched, non mulched) and four kinds of greenhouse air temperature (l.5, 3.2, 5.0, $6.7^{\circ}C$), and the results were summarized as follows: Temperature drop of medium in the V-bed was slower than that in the plant bed, showing better insulation effect of V-bed. Temperature drop of medium with mulching on the top of the bed was slower than the case without mulching, as a result, the beneficial effect of temperature drop was appeared in mulched bed. Linear regression of the temperature descent rate and the temperature difference between medium and air showed significant correlation. The regression equation for the Pearlite80% and Peatmoss20% in the V-bed was f(x) = -0.2656 + 0.1345x at the $R^2$ of 0.9269. Using the model, the temperature drop during night can be predicted for the various media at the different depths.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.17-27
• /
• 2011

This paper describes an experimental study and finite element analysis (FEA) carried out for investigating thermal deformation behavior of solders, resulting from temperature change in the solder. With such a goal in mind, a shear specimen that was composed of two metal bars having different coefficient of thermal expansion and solder blocks placed between two bars was designed and fabricated. Two different types of solder blocks, eutectic solder (Sn/36Pb/ 2Ag) and lead-free solder (Sn/3.0Ag/0.5Cu) were tested as well. Fringe patterns for several temperature steps were recorded and analyzed for three temperature cycles using a real-time moir$\acute{e}$ setup. The experimental data was verified with FEA and used to evaluate the suitability for numerous solder constitutive models available in literatures. FEA employing Anand material model suggested by Darveaux et al. and Chang et al. were found to be in an excellent agreement with the experimental results for the eutectic solder and the lead-free solder, respectively. In addition, numerical predictions on bending displacement, shear strain and viscoplastic distortion energy are documented and viscoplastic deformation behavior of two types of solder material are compared.

• Journal of the Society of Disaster Information
• /
• v.9 no.3
• /
• pp.324-331
• /
• 2013

Epoxy asphalt concrete is used to reduce dead load and to increase durability on long-span steel bridge overlay. The strength development properties of epoxy asphalt concrete are affected by time and temperature because epoxy asphalt is two-phase reactive materials. The strength development of epoxy asphalt concrete should be predicted precisely to decide traffic opening time. Based on this background in mind, the prediction model for traffic opening time for epoxy asphalt pavement was proposed in this research. The developed model using nonlinear curve fitting revealed R2 value of 0.943 while the R2 value of the existing model using chemical kinetics was 0.806. An improved precise prediction result is to be obtained when the prediction model uses accurate temperature data of pavement.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.2
• /
• pp.75-81
• /
• 2017

Modified atmosphere packaging (MAP) of vacuum, 60% $N_2/40%$ $CO_2$, 100% $N_2$ and 100% $CO_2$ were examined to preserve fried fish cakes and extend their shelf life. When product packages in air were stored at 5, 10, and $15^{\circ}C$ with measurement in quality attributes, aerobic bacterial growth was found to be primary quality factor to determine the shelf life of the product. Huang's model was adopted to obtain the parameters for use in shelf life determination for a variety of packaging and storage conditions. Temperature dependence expressed in Arrhenius equation showed activation energies of 139.4 and 41.8 kJ/mol for inverse of lag time and growth rate of the microbial spoilage, respectively. MAP of 100% $CO_2$ could double the product shelf life at $10^{\circ}C$ compared to air package. High $CO_2$ concentration MAP at low temperature was found to be effective to prolong the shelf life.

• Journal of Astronomy and Space Sciences
• /
• v.13 no.2
• /
• pp.105-116
• /
• 1996

This study is based upon the thermal modeling, analysis and operational results of KITSAT-1 and KITSAT-2 microsatellites launched on August 11, 1992 and Septermber 26, 1993, respectively. As KITSAT-1/2 was designed to be launched as an auxiliary payload of ARIANE launcher, the constraints on volume, power consumption, and mass were required to adopt passive thermal control method controlling absorptivity, emissivity, and conductivities among adjacent modules. The main of KITSAT was to take Earth images using CCD cameras positioned at the bottom of spacecraft, in which the cameras were always pointing to the center of Earth. This study is concerned with orbital analysis, thermal modeling, simulation results, and its verification by utilizing in-orbit telemetry data of KITSAT-2. The results of telemetry analysis show that the thermal modeling is matched to actual temperature data within 10 degrees of error range in average.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.9
• /
• pp.1648-1653
• /
• 2006

In this paper, transport characteristics have been investigated using analytical current-voltage model for double gate MOSFET(DGMOSFET). Scaling down to 100nm of gate length for MOSFET can bring about various problems such as a threshold voltage roll-off and increasing off current by tunneling since thickness of oxide is down by 1.fnm and doping concentration is increased. A current-voltage characteristics have been calculated according to changing of channel length,using analytical current-voltage relation. The analytical model has been verified by calculating I-V relation according to changing of oxide thickness and channel thickness as well as channel length. A current-voltage characteristics also have been compared and analyzed for operating temperature. When gate voltage is 2V, it is shown that a current-voltage characteristic in 77K is superior to in room temperature.

• Korean Journal of Materials Research
• /
• v.6 no.1
• /
• pp.99-105
• /
• 1996

본 연구에서는 TIMA를 전구체로 하는 수직형 MOCVD 반응기를 대상으로 수학적 모델을 세우고 컴퓨터에 의한 수치모사를 수행하여 반응기 설계 변수 및 공정조건이 AI의 증착속도와 증착두께 분포에 미치는 영향을 알아보았다. 수학적 모델은 수직형 반응기를 축대칭으로 보아 2차원으로 수립하였으며 반응기내의 운동량전달, 열전달, 물질전달을 포함한다. 이 수학적 모델의 지배 방정식들에 대하여 Galerkin 유한요소법을 적용하여 수치적으로 반응기 내의 유체 흐름 구조, 온도분포와 반응물의 농도 분포를 구하였다. 수치모사 결과 AI의 증착속도는 반응기 압력이 0.47torr, 기판온도가 25$0^{\circ}C$, 유량이 7.5sccm일 경우, 190-230$\AA$/min로 나타났다.