• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.141.1-141.1
• /
• 2011

New CCD BVR light curves of BD And are presented. Our light curves with nearly equal depths for both primary and secondary eclipses show well-defined photometric waves outside eclipse for all of BVR bandpasses. The orbital period is greatly revised as $0.^d92580519$ which is twice longer than that known previously. Sixteen timings from our observations and thirteen ones from the SuperWASP measurements were calculated. All available timings over 76 years, including ours, were analyzed to figure out the dynamical behavior of the system. It was found that the recent CCD O-C residuals varied in a cyclical way with a period of $9.^y18$ and a semi-amplitude of $0.^d0046$. The secondary period of $9.^y18$ is the most shortest one among those which have been ever found in the short period RS CVn binary stars. The periodic variation most likely arises from the light-travel time effect due to a low-mass ($m_3{\sim}0.88\;M_{\odot}$) tertiary companion moving in an orbit with an large eccentricity ($e_3$=0.70) and a low inclination ($i_3{\sim}28^{\circ}$). The Applegate mechanism could not operate properly in both components because the model parameters require too much large luminosity changes of ${\Delta}L/L_{p,s}$ > 10. The new light curves were synthesized using the 2003 version of Wilson-Divinney code. It was found useful to model two huge spots on the surface of the hotter star and a third-light in order to minimize the residuals from the observations. Astronomical basic parameters were deduced from our photometric solution.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.126.1-126.1
• /
• 2011

The SPICA (SPace Infrared Telescope for Cosmology & Astrophysics) project is a next-generation infrared space telescope optimized for mid- and far-infrared observation with a cryogenically cooled 3m-class telescope. Owing to unique capability of focal plane instruments onboard SPICA, it will enable us to resolve many astronomical key issues from the star-formation history of the universe to the planetary formation. The FPC (Focal Plane Camera) is a Korean-led near-infrared instrument as an international collaboration. Korean consortium for FPC proposed a key instrument responsible for a fine guiding (FPC-G). The back-up of FPC-G will make scientific observations as well. We have examined the legacy science programs for FPC and performed the feasibility study for the fine guiding system. Recently, the international review process is now in progress, in order to make a selection of the focal plane instruments. Here, we report the current status of SPICA/FPC project.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.5
• /
• pp.241-248
• /
• 1999

Recently, many linear motion generators and motors are rapidly finding applications that ranges from short stroke linear motion vibrators, such as dynamic cone type loudspeakers to stirling engine driven linear reciprocating alternators, compressors, textile machines etc. The stroke-length may go up to 2m, and the maximum speed is in the range of 5 to 10m/s with oscillating frequency as high as 15 kHz. Therefore, the linear oscillating actuators(LOAs) may be considered as variable speed drivers of precise controller with stoke-length and reversal periods during the reciprocating motion. In this paper, the design, fabrication, experiments, and extraction of control parameters of a moving coil type LOA for driving of linear reciprocating motion control systems, are treated. The actuator consists of the NdFeB permanent magnets with high specific energy as the stator produced magnetic field, a coil-wrapped nonmagnetic hollow rectangular bobbin structure, and an iron core as a pathway for magnetic flux. Actually, the design is accomplished by using FEM analysis for the basic configuration of a magnetic circuit, and characteristic equations for coil design. In order to apply as the drivers of a linear motion reciprocating control system, the control parameters and circuit parameters, such as input voltage-stoke, exciting frequency-stoke, coil inductance and so on, are extracted from the analysis and experiments on concerning a fabricating LOA.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.1
• /
• pp.33-49
• /
• 1997

One of the most important missons that are imposed on merchant ship at sea is to accomplish the safe transportation of cargo loaded. Recently, a study on the seakeeping performance has been carried out on the development of evaluation system related to the synthetic safety of a ship at sea. The seakeeping performance is the ship's ability sailing at, and executing its misson against adverse environmental factors successfully and safely. Until now, however, there has not been any method of quantitative evaluation on the dynamic safety of the ship's cargo loaded. In this regards, this paper has introduced the evaluation method of dynamic safety of the ship's cargo. In order to evaluate the dynamic safety of cargo, the vertical and lateral acceleration which causes the collapse, racking and local structure failure of cargo was adopted as the evaluation factors in the ship's motions. The response amplitude of ship's motions in regular waves is manipulated by NSM (New Strip Method) on a given 2,700 TEU full container vessel under the wind forces of 7, 8 and 9 Beaufort scale. Each response of ship's motions induced by NSM was applied to short-crested irregular waves for stochastic process on evaluation factors and then vertical and lateral acceleration of each cargo was compared with significant amplitude of each acceleration. A representative dangerous factor was determined by comparing permissible values of stacking and racking forces occurred typically to the vertical and transverse directions with the container strength required on ISO 1496 at the positions of forecastle, poop and ship's midship respectively. Through the occurrence probability of the determined factor by Rayleigh's probability density function, the dangerousness which limits loads on container's side wall as an evaluation was applied in judging of the danger of the ship's cargo loaded.

• Journal of Internet Computing and Services
• /
• v.2 no.4
• /
• pp.1-10
• /
• 2001

In this paper, we define requirements for call distribution of service control logic in Intelligent Network, Also, we propose call distribution mechanism for every subscriber with different call distribution rates, The call distribution mechanism had been developed as a function of Premium-rate Service in Intelligent Network. Our call distribution mechanism applies to percentage distribution instead of circular or hierarchical distribution. The call distribution mechanism consists of call input. output. call distribution processing logic part, random number generator, and customers database. We propose the practical implementation of a call distribution mechanism and call distribution decision indicating number computation method. We show three methods, the rand() function in C language, microsecond by system clock, and proposed algorithm, to get call distribution decision indicating number. In order to optimal call distribution mechanism, we estimated the results of three methods on occurrence values and the number of occurrences.

• Structural Engineering and Mechanics
• /
• v.35 no.6
• /
• pp.677-697
• /
• 2010

This paper focuses on geometrically non-linear static analysis of a simply supported beam made of hyperelastic material subjected to a non-follower transversal uniformly distributed load. As it is known, the line of action of follower forces is affected by the deformation of the elastic system on which they act and therefore such forces are non-conservative. The material of the beam is assumed as isotropic and hyperelastic. Two types of simply supported beams are considered which have the following boundary conditions: 1) There is a pin at left end and a roller at right end of the beam (pinned-rolled beam). 2) Both ends of the beam are supported by pins (pinned-pinned beam). In this study, finite element model of the beam is constructed by using total Lagrangian finite element model of two dimensional continuum for a twelve-node quadratic element. The considered highly non-linear problem is solved by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. In order to use the solution procedures of Newton-Raphson type, there is need to linearized equilibrium equations, which can be achieved through the linearization of the principle of virtual work in its continuum form. In the study, the effect of the large deflections and rotations on the displacements and the normal stress and the shear stress distributions through the thickness of the beam is investigated in detail. It is known that in the failure analysis, the most important quantities are the principal normal stresses and the maximum shear stress. Therefore these stresses are investigated in detail. The convergence studies are performed for various numbers of finite elements. The effects of the geometric non-linearity and pinned-pinned and pinned-rolled support conditions on the displacements and on the stresses are investigated. By using a twelve-node quadratic element, the free boundary conditions are satisfied and very good stress diagrams are obtained. Also, some of the results of the total Lagrangian finite element model of two dimensional continuum for a twelve-node quadratic element are compared with the results of SAP2000 packet program. Numerical results show that geometrical nonlinearity plays very important role in the static responses of the beam.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.1
• /
• pp.70-83
• /
• 2018

Korea's five leading industries-chemical, automobile, shipbuilding, metal and electronics-have been the growth engines of the Korean economy for the last 30 years. However, with their performance weakening in the past few years, Korea's annual growth rate has dropped to less than 2%. Just as the Japanese economy struggled through the lost decades, Korea's leading industries have been facing signals of arriving at a Strategic Inflection Point ("SIP") since the mid-2000s. The objective of this study is to present an appropriate value strategy for Korean firms in leading industries to gain sustainable competitive advantages. This paper examines the following issues : First, it diagnoses the signs and timing of SIP for the five leading industries. Second, this study examines 78 Korean and Japanese firms in order to understand the adaptation strategies of the highest and lowest performing firms from a value strategy point of view. Third, it empirically analyzes the correlation between the indicators of value strategy and the accounting performances of the Korean and Japanese firms. The data set used in the cluster analysis were collected from KISLINE database of NICE Information Service and annual reports. The findings in the case analyses of high and low performing companies show that high value-added specialty chemical materials and electronic component manufacturers that had a strong focus on value creation were defined as high performing companies. And in the cosmetic and automobile industries, companies with a strong emphasis on value appropriation gained high performance. Furthermore, the study conducted a cluster analysis based on two indicators R&D and advertisement expense. The analysis shows that a significant gap exists in the operating incomes among three groups classified under the value strategy. The study recommends that Korean firms are requested to increase R&D expenditure, conduct M&A and collaborate with companies that own source technologies to narrow the technology gap and improve their segment portfolio from commodity to value-added products.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.43 no.1
• /
• pp.132-142
• /
• 2020

Many countries around the world are pursuing various support policies to foster start-ups national widely in order to secure new economic growth engines in the era of the Fourth Industrial Revolution. The South Korean government announced the diffusion strategy for the 2'nd round Start-up Boom in March 2019 and is promoting the support policies for start-up incubating by various programs. Many incubators and startup accelerators operate various kinds of programs to foster start-ups using government financial supports. The purpose of this study is to investigate the effects of entrepreneurship and technical capability of entrepreneurs as the internal factors of the technology-based start-ups and the effects of programs supported by the government as an external factor on the corporate performance of a start-up company, and the mediating effects of core competence of start-ups were analyzed using SPSS and AMOS. The results show that the entrepreneurship, technical capability and the programs supported by incubators or accelerators had no direct effects on the corporate performance of a start-up, but the core competence of the company had complete mediating effects. In addition, the type of program supported by the comprehensive accelerator programs or the marketing supports had effects on the core competence rather than simple financial supports. Lastly, the policy proposals for incubating program support and future research directions along with the limitation are suggested.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.43 no.1
• /
• pp.7-15
• /
• 2020

It is a general phenomenon for manufacturers to provide vertically differentiated product line for more profit through improved market coverage. For such manufacturers, the compatibility between vertically differentiated products is an important decision issue. Some manufacturers provide full compatibility between high and low version products, whereas some provide only downward compatibility for the purpose of recommending high version product. In this study, the two representative compatibility strategies, full or downward, between vertically differentiated products produced by a single manufacturer are analyzed, especially under network externality and in the viewpoint of profit maximization. To do this we used a market model which captures the basic essence of vertical differentiation and network externality. Based on the proposed market model, the profit maximizing solutions are derived and numerically analyzed. The results can be summarized as follows : (1) Regardless of compatibility strategy, under network externality, vertical differentiation is always advantageous in terms of profit. (2) The full compatibility strategy is shown to be the most advantageous in terms of profit. In addition, it is necessary to make quality difference between differentiated products as wide as possible to maximize profit. (3) To gradually drive low version product out of the market and shift the weight pendulum of market to high version product, it is shown that the downward compatibility strategy is essential. Unlike intuition, however, it is also shown that in order to drive low version product out of market, it is necessary to raise the quality of the low version product rather than to lower it.

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.115-121
• /
• 2000

In comparison with thermosetting rubber, thermoplastic elastomer (TPE) has various advantages such as simple processing, short cycle time and recycling of scrap. These advantages can lead to development of the high value-added rubber products due to reduction of the waste material, manufacturing cost and the defected product. This article involves a dynamic vulcanization method for EPDM/polypropylene blend, and the manufacturing of a fixed glass weather-strip by glass insert molding method using the blend. In order to investigate mechanical properties of the product, tensile strength, elongation, hardness and specific gravity were measured. Also morphological study was carried out using SEM. Developments of an efficient system of production and automatic process by molding of TPE and glass simultaneously are expected.