• The Journal of the Acoustical Society of Korea
• /
• v.38 no.3
• /
• pp.352-362
• /
• 2019

The old residences and shops in the backside blocks are affected by the traffic noises from the main road. The noise of the backside roads is affected by the following factors such as the height of the roadside buildings, the distance between the road and the backside streets, distance among adjacent roadside buildings, and the difference of the adjacent building heights. The both noise levels on the road and the backside street were measured simultaneously in 15 urban blocks of a city which can be categorized into two types of roadside building plans ; 1) one single building along the street, 2) buildings arranged on one axis beside the road. As the results, there is no significant noise reduction due to the width of the buildings in general. However, in the cases of buildings arranged on one axis beside the road, it was found that the average noise reduction was 12 dB(A) on the basis of the building height of 4 m. Also, it was analysed that for each 4 m increase in the building height, noise reduction occurred by 2 dB(A) beyond building height of 4 m. In general, it was proved that the noise of the back streets is mainly affected by the lowest height of the roadside buildings. It was found that noise is increased by 1 dB(A) for each 4 m increase of the height difference between adjacent buildings. Also, It was revealed that for each 0.5 m increase in the distance between roadside building, noise reduction decreased by 1 dB(A).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.218-221
• /
• 2000

1999년 5월 4일부터 5월 7일까지 덴마크 오덴스에서 개최되었던 18차 ISO TC108/SC2 (기계 차량 구조물의 기계 진동 충격의 측정 및 평가) 총회내용 및 결의사항과 최근 진행되고 있는 ISO TC108/SC2 산하 규격 제 개정 동향에 대하여 살펴본다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.129-137
• /
• 2000

The powertrain is an important factor for the interior and exterior noise behavior of the vehicle Thus, the noise vibration and harshness(NVH) behavior of an engine is becoming a major target of the powertrain development. This paper describes the analyses with the aim to reduce the vibration and noise of an advanced inline 4-cylinder diesel engine block by use of CAE methods. The characteristics of an engine block as a main excitation source of car interior noise is studied. Particularly, The effect of balance shaft to reduce the 2nd order engine excitation force is calculated by forced vibration and radiated noise analysis. The engine exitation forces are obtained under real operating conditions. It is shown that the reduction of vibration and noise level by adapting blancing shaft is well predicted and rediated noise is directly related to the surface velocity of engine block.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.722-728
• /
• 2012

In railway vehicle, riding comfort depends mainly on the secondary lateral damper and track condition. When the damping force of lateral damper becomes abnormal condition or the track condition is worse, the running stability and ride comfort of the railway vehicles go down. In addition, the lateral motion of carbody is increased. Therefore, the lateral motion of carbody is reviewed carefully by considering lateral damping force and track condition of the railway line in design stage. In this study, the lateral displacement of carbody was studied in accordance with lateral damping force and track condition. The target vehicle is EMU for subway line.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.4
• /
• pp.329-334
• /
• 2013

Order spectrum analysis is widely used to grasp the features of noises due to powertrain system including engine and intake/exhaust system. It is known from many previous researches that order components related to the first and second firing frequencies of engine considerably affect the noise of car interior. The purpose of this paper is to find out the difference in sound quality: Pleasantness of car interior noise according to the change of its order spectrum. For this, car interior noises of 6-cylinder and 4-cylinder engines are recorded and their order spectrum levels are modified by applying adaptive digital filters. After subjective listening test employing paired comparison method is conducted, it is investigated that the level change of half-order components is a noticeable factor to improve Pleasantness of the car interior noises whereas level decrease of firing order does not always give the positive effect on its sound quality.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.9-11
• /
• 2021

Currently, the occurrence of floor noise in Korea is gradually increasing, and for this reason, the problem of secondary conflict is also increasing. Various studies have been conducted to solve these problems, but the definition of floor noise is not clear, and data of floor noise in various situations cannot be obtained. Therefore, this paper defines various scenarios of floor noise for floor noise epicenter recognition system. For this, the experimental scenario is defined in consideration of environment required for the experiment, the type of floor noise generated in real life, the location of the collector, and the noise intensity. It is possible to increase the accuracy of the floor noise epicenter recognition system when performing data collection and learning operations based on the defined experimental scenario.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.2
• /
• pp.86-92
• /
• 2001

Various array processing techniques to identify the noise source position or bearing have been developed. Typical array processing techniques which are based on time delay between received signals at two sensors, are classified as conventional beamforming, correlation function and NAH (Near-Field Acoustic Holography) techniques which have their own characteristics with respect to application field and signal processing method. In this study, correlation function technique which could be applied for broadband noise source detection, is adopted and the effective detection technique is proposed considering the effects of source bandwidth and measurement noise correlation of noise sources. The validity of the Proposed technique is evaluated using the 3-dimensional nonlinear any which does not give 3-dimensional Position or bearing ambiguity

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.270-275
• /
• 1995

본 논문에서는 3자유도를 갖는 2차원 강체날개의 플러터 속도를 향상시키는 축차 제어기를 설계하는 기법을 연구하였다. 먼저 2차원 강체날개의 운동방정식을 유도하고 플러터 해석을 수행하였다. 다음 수동계의 플러터 속도를 향상시키는 능동제어기를 설계한 후 제어기의 차수를 축차하는 기법을 적용하여 저차의 능동제어기를 구성하였다. 제어기 축차기법으로는 BACR을 사용하였으며 전차 제어기의 상태변수를 약 80%정도 줄일 수 있다. 축차된 제어기를 사용한 능동시스템과 전차 제어기를 사용한 능동시스템의 제어효과의 차이는 무시 할 수 있을 정도로 매우 작다. 따라서, BACR을 사용하여 얻은 축차된 제어기를 사용하면 상당한 계산량 감소효과와 실시간 단축효과를 얻을 수 있음을 확인하였다. 또한 동일한 돌풍입력에 대한 각각의 능동 시스템의 시간응답도 매우 양호한 결과를 얻을 수 있었으며, 전차 제어기를 사용한 능동시스템의 돌풍응답과 축차된 제어기를 사용한 능동시스템의 돌풍 응답 사이의 차이도 매우 작게 나타났다. 그러므로, 항공기 날개의 능동 플러터억제에는 BACR을 이용하여 설계한 축차된 제어기가 플러터 능동제어에 매우 유용하다고 할 수 있다. 그러나 BACR을 사용하기 위해서는 요구되는 정확도와 계산량에 대한 상호 절충과정이 반드시 필요하다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.295-301
• /
• 1997

본 연구의 목적은 수도권 전동차량의 주행성능을 평가하는 방법으로 진동성능을 비교검토하기 위하여 실차측정하고 분석한 것이다. 전동차량의 제작년도별로 측정대상차량을 샘플링하여 다양한 조건에서 진동을 측정하고 실측데이타를 시간영역의 통계적 방법으로 분석한 결과 제작년도에 따른 영향도 약간 나타났으며 전동차량의 2차 현가장치의 종류에 따른 영향을 발견할 수 있었다. 또한 측정선로구간의 특성에 따른 영향도 비교적 잘 나타나고 있음을 알 수 있었다.

• Journal of Korean Society of Forest Science
• /
• v.83 no.3
• /
• pp.400-409
• /
• 1994

To investigate the noise attenuation effects of various vegetation configurations, noise levels on 6 study sites along relatively heavy traffic roads were measured. The differences between noise level measures at 1m and 10m spots from the road range from 10 to 15dB depending upon the attributes of the vegetation. When flat grass land was set to control plot, the maximum noise attenuation at 10m spot was measured at the densely planted shrubs with 5dB difference. The areas on upward slope from the road showed the least attenuation effects. Based on the study results, an appropriate setting for low level residential area noise buffer belt would be densely planted shrubs with at least 3m width and 2m height. To be effective, 3m width soft areas covered with grasses are needed at the front and behind sides of the belt. More than 15dB of the noise level caused by the road traffic would be attenuated with the prescription.