• Journal of Biomedical Engineering Research
• /
• v.22 no.6
• /
• pp.543-550
• /
• 2001

In this study, ground reaction force(GRF) and energy consumption of fixed. single-axis and multi-axis Prosthetic ankle assemblies were investigated to show the biomechanical evaluation for trans-tibial amputees. In the experiments. two male and two female trans-tibial amputees were tested with fixed, sin91e-axis and multi-axis Prosthetic ankle assembly. A three-dimensional gait analysis was carried out to derive the ratio of GRF to weight as the percentage of total stance Phase for nine Points Energy consumption of each Prosthetic ankle assembly was measured while subjects walked at 2km/h. 3km/h and the most comfortable walking speed on the treadmill The results showed that multi-axis ankle was superior to the other two ankle assemblies for the characteristic of forwarding and breaking forces. Fixed ankle was relatively superior to the other two ankle assemblies for gait balancing and movement of the center fur mass Compared to the other ankle assembly. sing1e-axis type showed lower energy consumption over 2.3km/h walking speed .

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.04a
• /
• pp.181-187
• /
• 1997

고강도 알루미늄 합금 링롤재의 급냉, 링 팽창(expansion) 및 링 압축(compression) 응력제거처리후 잔류응력을 예측하기 위하여 2차원 축대칭 열해석 및 탄소성 해석을 수행하였다. 급냉 및 응력제거처리 후 2단 과시효 처리(T73)된 링롤재에 대하여 3단계 절단법(Three step sectioning method)을 적용하여 링롤재의 두께에 따른 잔류응력 분포를 측정하였으며, 측정결과를 급냉 및 응력제거처리후 잔류응력 해석결과와 비교분석하였다. 링의 급냉후 원주 및 축방향의 잔류응력 해석값은 T73후 측정값과 비슷한 경향을 보였으며, 링의 내면과 외면에서 압축응력을 나타내었고 중심에서 인장응력을 나타내었다. 잔류응력은 링 팽창(T7351) 및 링 압축(T7352) 적용후 T73에 비해 현저히 감소하였으며, 축방향의 제거 효과가 원주방향보다 우수하게 나타났다. 또한 링 압축에 의한 제거효과가 링 팽창보다 크게 나타났다. 링롤재의 응력제거처리는 제거 효과 및 실용성 측면에서 링 압축 공정이 유리하며, 치수제어 및 장비용량 측면에서 링 팽창 공정이 유리하다는 결론을 얻었다.

• Restorative Dentistry and Endodontics
• /
• v.26 no.1
• /
• pp.9-15
• /
• 2001

통상적인 근관형성 과정에서 근관형태의 직선화 경향을 발견할 수 있으며, 그 결과 만곡이 심한 근관에서 이상적인 근관형태를 얻기가 어렵다. 이를 극복하기 위한 많은 기구들과 근관 성형법들이 개선되고 소개되었다. 본 연구에서는 최근에 개발된 직사각형의 단면을 가지는 stainless steel file인 RT file과 Flex-R file, K-file을 이용하여 만곡근관 형성 후 최종 근관형태를 비교하여 각 file을 평가하고자 한다. 본 실험은 Bramante등의 방법을 변형하여 술 전의 근관형태와 술 후의 근관형태를 비교하였다. Schneider의 방법을 변형하여 3차원적 만곡을 계산하여 12도에서 36도 이내에 만곡도를 가진 근관을 선택하였다. 49개의 발거된 상악대구치 협측근관이나 하악대구치 근심근관을 3개의 군으로 나누고 레진과 플라스틱으로 제작된 mold에 투명한 교정용 레진으로 매몰하였다. 근첨에서 2.5, 5, 8mm지점에서 절단하여 각 mold에서 재조립한 후 다음과 같이 근관형성을 시행하였다. 제 1군은 SS K-file을 이용하여 step-back 방법 ; 제 2군은 Flex-R file을 이용하여 balanced force 방법 ; 제 3군은 RT file을 이용하여 step-back 방법으로 근관 형성하였다. 술 전과 술 후에 각 시편들을 체현미경으로 사진촬영하여 근관 중심 위치 이동률, 근관형성으로 삭제된 상아질양, 근관형성 후 모양을 Sigma scan/ image software program으로 계산하고 One way ANOVA로 통계적 유의성을 검증하여 다음과 같은 결론을 얻었다. 1. RT file이 치근단에서 K-file보다 유의성 있게 근관의 중심을 유지하는 것으로 보였다. 치아 중앙부에서는 RT file과 Flex-R file이 K-file에 대해 유의성 있게 우수한 것으로 나타났다. 2. 근관형성 후 삭제된 상아질양에서는 치근단에서 RT file이 적게 나왔으나 유의성은 없었다. 3. 근관형성 후 절단면 모양은 원형, 타원형, 불규칙한 형태들이 다양하게 나타났고 각 군간에 유의성 있는 차이는 없었다.

• The korean journal of orthodontics
• /
• v.32 no.4 s.93
• /
• pp.275-291
• /
• 2002

Of various factors indicated for effective use of straight wire appliances, there was a great lack of studies both domestic and international about the curvatures of tooth crowns. This study was performed to investigate the labio/buccal clinical crown curvatures of Korean permanent teeth. For this study, three-dimensional laser scanning was performed on 36 dental casts with normal anatomic structures. Andrews plane and Facial axis of clinical crown (FACC) were designated as horizontal and vertical reference planes respectively. 2 or 3 lines, 1mm apart, were drawn superior, inferior, left and right of these reference planes. A three-dimensional coordinate table was made for points formed by crossing these lines, and averages of each coordinate point on the 36 dental casts were obtained. The curvature equation was made using three-dimensional coordinate points (x,y,z) and by this curvature equation, the curve ratio of each tooth was obtained. Curve ratio changes of each section of teeth were calculated by curve ratios of simplified curves. These two dimensional curves were simplified horizontally and vertically Conclusions for this study are as follows. 1. The basic data of labial and buccal clinical crown curvatures were obtained about Korean permanent teeth. 2. No significant difference was found between male and females. 3. Individual tooth characteristics 1) In maxillary central incisors, the difference in the curve ratio between the gingival and incisal sides was greater than for the other teeth. And the gingival side showed a greater curve ratio. 2) Maxillary canines showed more curvatures in the mesio-occlusal surface than the other surfaces. 3) In maxillary $1^{st}$ premolars, more curvatures were found in mesio-occlusal and disto-gingival surface, thus showing a twisted crown surface, but in maxillary $2^{nd}$ premolars, the crown curvatures of mesial and distal ends became parallel to each other. 4) No significant difference in crown curvatures was found between mandibular central and lateral incisors. 5) Occluso-gingival curvatures of mandibular$2^{nd}$ premolar turned out to be more rounded than mandibular $1^{st}$ premolars or maxillary $2^{nd}$ premolars. From the above conclusions, it can be deduced that the same bracket bases can be used for mandibular central and lateral incisors. But for maxillary $1^{st}\;and\;2^{nd}$ premolars and for mandibular $1^{st}\;and\;2^{nd}$ premolars, because crown curvatures showed significant differences, when making bracket bases there is ample reason to make bracket base curves differently for each type of tooth.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.424-435
• /
• 1991

To develop the photoelastic experiment method for the orthotropic material under pure torsional moment is the main objective of this research. In the development of photoelastic experiment for orthotropic material under pure torsional moment, the important problems and their solutions are the same as following. In the model material for photoelastic experiment, it was found that C.F.E.C.(Copper Fiber Epoxy Composite) can be used as the model material of photoelastic experiment for orthotropic material. In the stress freezing cycle, it was assured that stress freezing cycle for epoxy can be used as the stress freezing cycle of the photoelastic experiment for orthotropic material. In the slicing method, it was found that the negative oblique slicing method can be effectively used as slicing method in 3-dimensional photoelastic experiment. In the measuring method of stress fringe values and physical properties in the high temperature, it was found that stress fringe values can be directly measured by experiment and physical properties can be directly or indirectly by equation between stress fringe values and physical properties developed by author. In the stress analysis method of orthotropic material under pure torsional moment by photoelastic experiment, it will be studied in the second paper.

• Journal of Welding and Joining
• /
• v.30 no.4
• /
• pp.44-48
• /
• 2012

H-beam used for stiffening the upper structure of ocean plant is cut in the various shapes. The cutting process of the H-beam is done manually and requires a long time and high cost. Therefore, automation of H-beam cutting is an important task. This research aims to develop a 3-D simulator to build the automatic H-beam cutting system and to determine the optimal cutting method. The automatic H-beam cutting system composes of 6 robots including 2 cutting robots hang to a crane and 1 conveyer. The appropriate system layout for covering the various sizes and types of H-beam was tested and determined using the simulator. The H-beam cutting system uses a hybrid type of plasma and gas cutting because of special cutting shapes of H-beam. The cutting area of each cutting method should be properly divided according to the size and shape of H-beam to shorten the total cutting time. Additionally the collision between a robot and a robot or a robot and H-beam should be avoided. The optimal cutting method for the shortest cutting time without the collision could be found for the various cutting conditions by use of the simulator. 2 simulation samples shows the availability of the simulator to find the optimal cutting method.

• Journal of Korean Institute of Industrial Engineers
• /
• v.27 no.4
• /
• pp.424-431
• /
• 2001

This paper is concerned with the unconstrained two-dimensional cutting problem of cutting small rectangles (products), each of which has its own profit and size, from a large rectangle (material) to maximize the profit-sum of products. Since this problem is used as a sub-problem to generate a cutting pattern in the algorithms for the two-dimensional cutting stock problem, most of researches for the two-dimensional cutting stock problem have been concentrated on solving this sub-problem more efficiently. This paper improves Hifi and Zissimopoulos's recursive algorithm, which is known as the most efficient exact algorithm, by applying newly proposed upper bound and searching strategy. The experimental results show that the proposed algorithm has been improved significantly in the computational amount of time as compared with the Hifi and Zissimopulos's algorithm.

• Proceedings of the Korean Information Science Society Conference
• /
• 2008.06b
• /
• pp.281-285
• /
• 2008

본 논문에서는 임의의 두 얼굴간의 얼굴 변형을 시뮬레이션하는 방법으로서 직선형 경로를 이용한 얼굴 모핑 알고리즘을 소개한다. 이 때 두 얼굴 모델은 서로 독립적으로 3D 스캔되어 텍스처매핑을 거쳐서 생성된 별도의 3D 모델로서, 본 알고리즘은 이러한 얼굴 모델들간의 버텍스와 폴리곤의 개수와는 상관없이 자연스러운 모핑을 구현하는 특징을 갖는다. 알고리즘의 주요 기능으로는 절단면의 생성, 3 차원 메쉬의 2D 메쉬화, 대응 영역의 설정, 대응 폴리곤 탐색 및 보간 데이터 추출등이 포함된다.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.30 no.4
• /
• pp.61-70
• /
• 2005

In this Paper, we develop an improved branch and bound algorithm for the (un)weighted unconstrained two-dimensional cutting problem. In the proposed algorithm, we improve the branching strategies of the existing exact algorithm and reduce the size of problem by removing the dominated pieces from the problem. We apply the newly Proposed definition of dominated cutting pattern and it can reduce the number of nodes that must be searched during the algorithm procedure. The efficiency of the proposed algorithm is presented through comparison with the exact algorithm known as the most efficient.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2000.04a
• /
• pp.393-396
• /
• 2000

본 연구에서는 필렛엔드밀을 이용하여 복합곡면을 가공하기 위한 새로운 접근방법을 제안한다. 이 방법은 "곡선기반 접근방법"으로 기존의 "점기반 접근방법"에 비하여 몇 가지 특징들을 가지고 있다. 본 연구에서는 다면체로 표현된 곡면을 대상으로 하고 있는데, 볼록한 모서리와 꼭지점에서는 정확히 옵셋시키고 오목한 부위에서는 옵셋 곡면이 겹치는 것을 허용한다. 옵셋된 곡면을 절단 평면으로 자르고, 같은 평면상에 있는 교선 중에서 겹치는 부분의 윗 부분을 택하면 공구 간섭이 제거된 공구 경로를 얻게된다. 즉 계산이 복잡한 오목지역에서의 옵셋 시 발생되는 간섭을 2차원 평면상에서 제거함으로써 계산 과정을 단순화시키고 안정적으로 만든다. 본 연구에서 제안한 방법은 PC에서 VC++로 구현되었으며 몇 가지 적용 예를 보여 주고 있다.