• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.1
• /
• pp.1-8
• /
• 1997

In order to reject the steady-state tracking error, it is common to introduce integral compensators in servosystems for constant reference signals. However, if the mathematical model of the plant is exact and no disturbance input exists, the integral compensation is not necessary. From this point of view, a two-degree-of-freedom(2DOF) servosystem has been proposed, in which the integral compensation is effective only when there is a modeling error or a disturbance input. The present paper considers robust stability of this 2DOF servosystem incorporating an observer to the structured and unstructured uncertainties of the controlled plant. A robust stability condition is obtained using Riccati inequality, which is written in a linear matrix inequality (LMI) and independent of the gain of the integral compensator. This result impies that if the plant uncertainty is in the allowable set defined by the LMI condition, a high-gain integral compensation can be carried preserving robust stability to accelerate the tracking response.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.199-202
• /
• 1995

In the conventional $H_2$ design of PI controllers, the quadratic cost function includes only the plant output term and hence, the optimal controller often results in a very large plant input. In this paper, $H_{\infty}$ design methodology is combined with the conventional $H_2$ design to make a trade-off between the regulation of the plant input and the plant output in a systematic way.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.380-388
• /
• 2016

Using the magnet gear, it is possible to transmit power without mechanical contact. As the drive shaft in a magnet gear-based speed reducer system is isolated from the drive shaft, the system is a two-inertia resonance system that should cope with an external load with the limited air-gap stiffness. On the other hand, the drive shaft or low-speed side is controlled only by the torque of the drive shaft through an air-gap, and the excessive oscillation or the slip can then be generated because of an abrupt disturbance that is different from the general mechanical gear system. Therefore, the disturbance loaded at the low speed side should be measured or estimated, and considered in the control of the driving shaft. This paper proposes a novel full-state feedback controller with a reduced-order observer for the speed reducer system using a magnet gear with a unified harmonic modulator. The control method was verified by simulation and experiment. To estimate the load at the low speed side, a novel observer was designed, in which the new state variable is introduced and the new state equation is formulated. Using a full-state feedback controller including the observer, the test result against disturbance was compared with two D.O.F PI speed controllers. The pole slip was compensated within relatively a short time, and the simulation result about the estimated variable shows a similar tendency to the test result. The test results showed that the magnet gear-based reducer can be applied to an accurate servo system.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.1 s.307
• /
• pp.13-20
• /
• 2006

In this paper, we propose a motion control scheme of robot manipulators based on visual feedback under camera-in-hand configuration. The desired joint velocity and acceleration for motion control is made by the feature-based visual data in the outer loop. The control input for tracking feature points on the image plane uses robot kinematics dynamic. The proposed control input consists of the image feature and the joint velocity error to achieve robustness to the parametric uncertainty. The stability of the closed-loop system is proved by Lyapunov approach. Computer simulations and experiments on a two degree of freedom manipulator with 5 links are presented to illustrate the performance of proposed control system.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.565-570
• /
• 2011

In this paper, the analytical tuning rules of the proportional-integral-derivative (PID) controller have been derived for a broad class of stable, integrating, and unstable processes without time delay. On the basis of the renowned internal model control (IMC) design principles and the two-degree-of-freedom (2DOF) control structure, the proposed method can be effectively used for obtaining the enhanced performances of both the disturbance rejection as well as the set-point tracking problems, since the design scheme is simple, straightforward, and can be easily implemented in the process industry. Several processes without time delay are employed to demonstrate the improved closed-loop performance of the proposed controller design in compared with the other well-known design methods in terms of the same degree of robustness.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.5
• /
• pp.486-502
• /
• 1989

This paper proposes two types of the preview algorithms to predict the velocities and joint positions, and deals with a control approach using the preview algorithms for the precise trajectory control. Specifically, a predictor as the form of discrete time state equations is proposed based on the robot dynamics model linearized by the computed toque method. And another state predictor is proposed by the best line fitting in the least square sense, where present joint velocities and positions and several past positions are employed. Then computer simulations are performed for the SCARA robot with two d.o.f to show the validities of the proposed algorithms.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.3
• /
• pp.248-257
• /
• 2007

This paper presents the control system for driving myoelectric hand prosthesis according to myoelectric signal generated in the human muscle. A surface myoelectric sensor for measuring myoelectric signal is designed a skin interface and a processing circuit according to myoelectric signal output property. The control system consists of two controller for driving dual motor, torque sensor for measuring out torque of motor, slip sensor for detecting slip of torque. The experimental results proved the proposed control system.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.26 no.2
• /
• pp.147-152
• /
• 2016

Shape Memory Alloys (SMAs) undergo changes in shape and hardness when heated or cooled, and do so with great force. Since wire-type SMAs contract in length when heated and pull with a surprisingly large force and move silently, they can be used as actuactors which replace motors. These SMA actuators can be heated directly with electricity and can be used to create a wide range of motions. This paper presents the mechanical design and control for a three fingered, six degree-of-freedom robotic hand actuated by SMA actuators. Each finger has two joints and each joint is actuated with two tendons in the antagonistic manner. In order to create the sufficient force to make the smooth motion, the tendon is composed of two SMA actuators in parallel. For controlling the current to heat the SMA actuators, PWM drivers are used. In experiments, the antagonistic interaction of fingers are evaluated.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.3
• /
• pp.321-328
• /
• 1998

When we control the level of the steam generator in the nuclear power plants, a swell and shrink arises from many disturbances such as feed water rate, feed water temperature, main steam flow rate, and coolant temperature. If we use the conventional type of PI controller in this system, we will not have stability during controlling at lower power, the removal function of disturbances, and a load follow-up control effectively. In this paper, we study the application of a 2-Degree of Freedom(2-DOF) PID controller to the level control of the steam. generator of nuclear power plants through the simulation and the experimental steam generator. We use the parameters $\alpha$, $\beta$, $\gamma$ of the 2-DOF PID controller for the removal of disturbances and the parameters Kp,Ti,Td of the conventional type of PID controller for controlling setpoint. The back-propagation learning algorithm of neural network is used for tuning the 2-DOF PID controller. We can find satisfactory results of the removal of the disturbances and the tracking function in the change of setpoint through the simulation and experimental steam generator.

• Journal of Power System Engineering
• /
• v.4 no.3
• /
• pp.62-71
• /
• 2000

A mathematical modeling for a magnetic levitation system is proposed using the Taylor series expansion of differential function for obtaining linearity. It is confirmed that this kind of linear approximation method can be used to the modeling of a magnetic levitation system. The two-degree-of-freedom optimal servo system for a constant reference signal is proposed using the LQ optimization technique. An additional state feedback is introduced at the output of the integrator to cancel the integral action for reference signal if there is no modeling error of the plant and no disturbance input to the plant. When the modeling error or the disturbance input exists, the integral effect appears. The system has a free parameter which can b used to tune the effect of the integral compensation.