• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.646-652
• /
• 2013

EU's Galileo project is a market-based GNSS (Global Navigation Satellite System) that is under development. It is expected that Galileo will provide the positioning services based on new technologies in 2020s. Because Galileo E1 signal for OS (Open Service) shares the same center frequency with GPS L1 C/A signal, CBOC (Composite Binary Offset Carrier) modulation scheme is used in the E1 signal to guarantee interoperability between two systems. With E1 signal consisting of a data channel and a pilot channel at the same frequency band, there exist several options in designing signal acquisition for Assisted-Galileo receivers. Furthermore, compared to SNR worksheet of Assisted-GPS, some factors should be examined in Assisted-Galileo due to different correlation profile and code length of E1 signal. This paper presents SNR worksheets of Galileo E1 signals in E1-B and E1-C channel. Three implementation losses that are quite different from GPS are mainly analyzed in establishing SNR worksheets. In the worksheet, hybrid long integration of 1.5s is considered to acquire weak signal less than -150dBm. Simulation results show that the final SNR of E1-B signal with -150dBm is 19.4dB and that of E1-C signal is 25.2dB. Comparison of relative computation shows that E1-B channel is more profitable to acquire the strongest signal in weak signal environment. With information from the first satellite signal acquisition, fast acquisition of the weak signal around -155dBm can be performed with E1-C signal in the subsequent satellites.

• Journal of IKEEE
• /
• v.3 no.1 s.4
• /
• pp.69-78
• /
• 1999

In this paper, direct conversion receiver was designed to even harmonic anti-paralled diode pair ring mixer. Using a second harmonic component of LO instead of LO signal and RF signal are mixed by SHP(Sub Harmonic Pumped) mixer with anti-parallel diode pair. Canceling the harmonics of LO signal in ring mixer, SHP mixer using anti-parallel diode pair could mostly reduce the radiation of LO signal through a input port the most, good isolation characteristic, and low spurious characteristic by LO signal was shown over broad band. The produced SHP mixer showed LO/IF, RF/IF and LO/RF isolation was 24.6dB,36.2dB and 22.5dB respectively. And conversion loss was measured 15.6dB, IF output -35.6dBm with -20dBm RF input and 5.5dBm LO signal. 1dB compression point of If signal, in respect to RF signal, was found at the 0dbm RF signal.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.1
• /
• pp.46-54
• /
• 2021

In this paper, active noise control was performed to reduce radiated noise in the low frequency band of dishwashers. First, through an analysis of the noise environment of the dishwasher, it was confirmed that the pump noise contributed the most to the radiated noise in the low frequency band, From the result of the noise environment analysis, the reference signal was selected to be the vibration signal of the pump body. The reference signal was obtained by using the accelerometer on the pump body, which can prevent acoustic feedback. The error signal sensor was selected as a microphone located at 1 m in front of the dishwasher and 0.5 m in height. And to design the controller, the error signal and the reference signal were measured at the operational rpms of the dishwasher at 2,500 rpm, 2,600 rpm and 2,800 rpm, and the secondary path transfer function was measured. The designed controller was mounted on Digital Signal Processor (DSP) equipment, and the control performance was verified experimentally. As a result of the measurement at the 3 operational rpms, the 7th multiple component of pump operating frequency decreased by 1.93 dB, 4.43 dB, 5.15 dB per rpm, and the 12th multiple component decreased by 6.67 dB, 2.34 dB, 4.28 dB per rpm. And overall Sound Pressure Level (SPL) decreased by 0.84 dB, 2.58 dB, 1.48 dB by rpm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1392-1398
• /
• 2000

In this paper, Sub Harmonic Ring Mixer using Anti-Parallel Diode Pair is studied. Conventional mixers mix LO signal with RF signal and, obtain IF signal from the difference between LO and RF. Sub harmonic ring mixers using APDP mix RF signal with the second harmonic of LO signal, LO frequency needed for conventional receiver is reduced by 1/2.The produced mixer showed 12 dB conversion loss, and 1 dB compression point of IF signal, in respect to RF signal, was found at the 0 dBm RF signal. Isolation LO/IF and LO/RF is 24.6 dB and 22.5 dB respectively. Isolation RF/LO and LO/RF is 32.6 dB and 22.5 dB respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.103-109
• /
• 2003

We have proposed the 4-Dimensional Multiple-Subcarrier Modulation with fixed bias in Optical Wireless Communications. Here, the 4-D signal vectors are derived from the optimization technique of signal waveforms maximizing the minimum distance between signal points in an n-dimensional Euclidean sphere. The resulting vectors are used in generating the output amplitude of impulse generator in a Multiple-Subcarrier Modulation scheme. We have achieved that the normalized power requirement of the proposed system is maximum 3 dB and 3.3 dB smaller than those of normal QPSK, Reserved Subcarrier, and Minimum Power scheme, respectively. Also, in the range of 1.125 ∼ 1.25 of the normalized bandwidth, the proposed system has maximum 3 dB, 2 ∼ 4 dB, 0 ∼ 3 dB smaller bandwidth requirement compare to normal QPSK, Res. Subcarrier, Min. Power schemes, respectively.

• Journal of electromagnetic engineering and science
• /
• v.15 no.4
• /
• pp.232-238
• /
• 2015

This work describes the development of a D-band (110-170 GHz) signal source based on a SiGe BiCMOS technology. This D-band signal source consists of a V-band (50-75 GHz) oscillator, a V-band amplifier, and a D-band frequency doubler. The V-band signal from the oscillator is amplified for power boost, and then the frequency is doubled for D-band signal generation. The V-band oscillator showed an output power of 2.7 dBm at 67.3 GHz. Including a buffer stage, it had a DC power consumption of 145 mW. The peak gain of the V-band amplifier was 10.9 dB, which was achieved at 64.0 GHz and consumed 110 mW of DC power. The active frequency doubler consumed 60 mW for D-band signal generation. The integrated D-band source exhibited a measured output oscillation frequency of 133.2 GHz with an output power of 3.1 dBm and a phase noise of -107.2 dBc/Hz at 10 MHz offset. The chip size is $900{\times}1,890{\mu}m^2$, including RF and DC pads.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.152-159
• /
• 2016

This paper describes an offset and 1/f noise cancellation technique based hall sensor signal processor. The hall sensor outputs a hall voltage from the input magnetic field, which direction is orthogonal to hall plate. The two major elements to complete the hall sensor operation are: the one is a hall sensor to generate hall voltage from input magentic field, and the other one is a hall signal process system to cancel the offset and 1/f noise of hall signal. The proposed hall sensor splits the hall signal and unwanted signals(i.e. offset and 1/f noise) using a spinning current biasing technique and chopper stabilizer. The hall signal converted to 100 kHz and unwanted signals stay around DC frequency pass through chopper stabilizer. The unwanted signals are bloked by highpass filter which, 60 kHz cut off freqyency. Therefore only pure hall signal is enter the ADC(analog to dogital converter) for digitalize. The hall signal and unwanted signal at the output of an amplifer and highpass filter, which increase the power level of hall signal and cancel the unwanted signals are -53.9 dBm @ 100 kHz and -101.3 dBm @ 10 kHz. The ADC output of hall sensor signal process system has -5.0 dBm hall signal at 100 kHz frequency and -55.0 dBm unwanted signals at 10 kHz frequency.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.87-90
• /
• 2003

In this paper, A feedforward linear power amplifier is analyzed for imperfect signal cancellation and negative feedback for basestaion of IMT2000 band. the distortion generatied by the error amplifier is reduced using an imperfect signal cancellation for a 1-carrier WCDMA source by 4.3dB at 2.5MHz offset and 6dB at 5MHz offset of IMSR(intermodulation signal power ratio) compared to a perfect signal cancellation system. additionally, An imperfect signal cancellation using negative feedback improved 1.3dB and 8.2dB at 2.5MHz and 5MHz offset of IMSR compared to an imperfect signal cancellation.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.5
• /
• pp.45-51
• /
• 1993

An erbium doped fiber amplifier(EDFA) pumped by aingle 1.48$\mu$m LD was fabricated, and its gain and noise characteristics were measured. As a signal source, 1548 nm wavelength DFB LD was used. The small signal net gain of the EDFA module was 21.8 dB with maximum gain coefficient 0.7dB/mW for the erbium fiber length of 17.6 m, the pump power of 58 mW, and an input signal power of -25 dBm, respectively. The saturation power of the EDFA was 1 dBm for the input signal power of -5 dBm and the noise figure, measured by using an optical spectrum analyzer, was 5.8 dB for the input signal power of -40 dBm.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.45-49
• /
• 2007

We have investigated the optimum combination of the environmental noise condition and type of SQUID pickup coil in order to obtain maximum signal-to-noise ratio (SNR). The measurement probe consists of 1st order gradiometer with pickup coils of 100 mm, 70 mm, and 50 mm baseline length, a 2nd order gradiometer with 50 mm baseline, and a magnetometer. The pickup coils are fabricated by winding Nb wire on a bobbin with 200 mm diameter. Noise and heart signal of a healthy male were measured by various SQUID sensors with different types of pickup coils in various magnetically shielded rooms (MSR), and compared to each other. The shielding factors were found to be 43 dB, 35 dB and 25 dB at 0.1 Hz for MSR-AS, MSR-BS, MSR-CS, respectively. White noises were $3.5\;fT/Hz^{1/2}$, $4.5\;fT/Hz^{1/2}$ and $3\;fT/Hz^{1/2}$ for the 1st order gradiometers, the 2nd order gradiometers, and magnetometer for all MSRs. SNR of the magnetometer was up to 56 dB in MSR-AS, while the 1st order axial gradiometer with 70 mm baseline length was up to 54 dB in MSR-BS. The 2nd order axial gradiometer with 50 mm baseline length of pickup coil was found to be up to 40 dB in MSR-CS.