• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.54-63
• /
• 1997

The 1-D finite-element mehtod is applied for designing double-clad otpical fibers with dispersion-compensation capability. design parameters allowing only a $LP_{01}$ single mode are treated and macro-bending loss are taken into consideration. Design parameters are extracted to have the compensation ratio $(L_{SMF}/L_{DCF})$ of 6.2 for core structure with step-index profile, and of 5.2 for core with triangular-index profile.

• The Journal of Korea Robotics Society
• /
• v.12 no.1
• /
• pp.78-85
• /
• 2017

This paper presents the development of a 3D printer based piezo-driven vertical micro-positioning stage. The stage consists of two flexure bridge structures which amplify and transfer the horizontal motion of the piezo-element into vertical motion of the end-effector. The stage is fabricated with ABS material using a precision 3D printer. This enables a one-body design eliminating the need for assembly, and significantly increases the freedom in design while shortening fabrication time. The design of the stage was optimized using response surface analysis method. Experimental results are presented which demonstrate 100nm stepping in the vertical out-of-plane direction. The results demonstrate the future possibilities of applying 3D printers and ABS material in fabricating linear driven motion stages.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2003.05a
• /
• pp.361.1-361.1
• /
• 2003

• The Research Journal of the Costume Culture
• /
• v.24 no.3
• /
• pp.315-323
• /
• 2016

The present study is intended to study sole types necessary for shoe designs for elementary school students that are in age groups in growth periods, and 3D midsole design utilizing 3D printing technology. This study analyzed data from the 3D measurement of the feet of 1,227 elementary school students aged 7-13 years residing in the capital region conducted as part of the 6th Anthropometry of Size Korea. In addition, 3D midsoles by sole type were designed utilizing a Rhino CAD, and midsole prototypes were output utilizing a Zortrax-M200 3D Printer. Through a cluster analysis of sole shapes by type, sole shapes were classified into three types. Type 1 has small values of foot lengths and foot breadths, with large toe 1 angles and high arch heights. Type 2 has intermediate values of foot lengths and foot breadths, with small toe 1 angles and high arch heights. Type 3 has large values of foot lengths and foot breadths with small toe 1 angles and low arch heights. On reviewing the results of design of 3D midsoles by sole type, it can be seen that the midsoles were designed according to characteristics by sole type. The results of the sole type analysis in the present study are expected to be meaningful as basic data for the development of shoe insoles for elementary school students.

• Journal of Computational Design and Engineering
• /
• v.2 no.1
• /
• pp.47-54
• /
• 2015

In recent years, 3D printers have become popular as a means of outputting geometries designed on CAD or 3D graphics systems. However, the complex user interfaces of standard 3D software can make it difficult for ordinary consumers to design their own objects. Furthermore, models designed on 3D graphics software often have geometrical problems that make them impossible to output on a 3D printer. We propose a novel AR (augmented reality) 3D modeling system with an air-spray like interface. We also propose a new data structure (octet voxel) for representing designed models in such a way that the model is guaranteed to be a complete solid. The target shape is based on a regular polyhedron, and the octet voxel representation is suitable for designing geometrical objects having the same symmetries as the base regular polyhedron. Finally, we conducted a user test and confirmed that users can intuitively design their own ornaments in a short time with a simple user interface.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1465-1470
• /
• 2006

This paper presents a design of low power CMOS LNA(Low Noise Amplifier) for 2.4 GHz ZigBee applications that is a promising international standard for short area wireless communications. The proposed circuit has been designed using TSMC $0.18{\mu}m$ CMOS process technology and two stage cascade topology by current reuse technique. Two stage cascade amplifiers use the same bias current in the current reused stage which leads to the reduction of the power dissipation. LNA design procedures and the simulation results using ADS(Advanced Design System) are presented in this paper. Simulation results show that the LNA has a extremely low power dissipation of 1.38mW with a supply voltage of 1.0V. This is the lowest value among LNAs ever reported. The LNA also has a maximum gain of 13.38dB, input return loss of -20.37dB, output return loss of -22.48dB and minimum noise figure of 1.13dB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.259-262
• /
• 2006

This paper presents a design of low power CMOS LNA(Low Noise Amplifier) for 2.4 GHz ZigBee applications. The proposed circuit has been designed by using TSMC $0.18{\mu}m$ CMOS process and current-reused two-stage cascade topology. LNA design procedures and the simulation results using ADS(Advanced Design System) are presented in this paper. Simulation results shows that the LNA has a extremely low power dissipation of 1.38mW with a $V_{DD}$ of 1.0V. The LNA also has a maximum gain of 13.38dB, input return loss of -20.37dB, output return loss of -22.48dB and noise figure of 1.13dB.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.117-123
• /
• 2013

By calculating the spectral efficiency of symmetric balance incomplete block design(BIBD) codes satisfying BER=$10^{-9}$, it can be found that ideal BIBD code design with m=2 and various q's is effective when effective power is high($P_{sr}=-10$ dBm). But BIBD code design with q > 2 and various m's can be effective when effective power is low($P_{sr}=-25$ dBm).

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.3B no.1
• /
• pp.23-31
• /
• 2003

A novel 3D shape optimization algorithm is presented for electromagnetic devices carry-ing eddy current. The algorithm integrates the 3D finite element performance analysis and the steepest descent method with design sensitivity and mesh relocation method. For the design sensitivity formula, the adjoint variable vector is defined in complex form based on the 3D finite element method for eddy current problems. A new 3D mesh relocation method is also proposed using the deformation theory of the elastic body under stress to renew the mesh as the shape changes. The design sensitivity f3r the sur-face nodal points is also systematically converted into that for the design variables for the parameterized optimization application. The proposed algorithm is applied to the optimum design of the tank shield model of the transformer and the effectiveness is proved.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3413-3420
• /
• 2021

Applying the available neutron flux for medical and industrial purposes is the most important application of research reactors. The neutron radiography system is used for non-destructive testing (NDT) of materials so that it is one of the main applications of nuclear research reactors. One of these research reactors is the 5 MW pool-type light water research reactor of Tehran (TRR). This work aims to investigate on materials and location of the beam tube (BT) of the TRR radiography system to improve the index parameters of BT. Our results showed that a through-type BT with 20 cm thick carbon neutron filter, 1.2 cm and 9.4 cm of the diameter of inlet (D₁) and output (D₂) BT, respectively gives thermal neutron flux almost 25.7, 5.6 and 1.1 times greater than the former design of the TRR (with D₁ = 1.8 cm and D₁ = 9.4 cm), previous design of the TRR with D₁ = 3 cm and D₁ = 9.4 cm, and another design with D₁ = 5 cm and D₁ = 9.4 cm, respectively. Therefore, the design proposed in this paper could be a better alternative to the current BT of the TRR.