• Journal of Environmental Science International
• /
• v.22 no.11
• /
• pp.1481-1498
• /
• 2013

The SCR (selective catalytic reduction) system is highly-effective technique for NOx reduction from exhaust gases. In this study, the effects of the direction and size of nozzle and the ammonia injection concentration on the performance of SCR system are analyzed by using the computational fluid dynamics method. When the nozzle is arranged in zigzaged direction which is normal to exhausted gas flow, it is shown that the uniformity of gas flow and the NH3/NO molar ratio is improved remarkably. With the change of the ammonia injection concentration from 0.2 vol%(wet) to 1.0 vol%(wet), the uniformity of gas flow shows a good results. As the size of nozzle diameter changes from 6 mm to 12 mm, the uniformity of gas flow is maintained well. It is shown that the uniformity of the $NH_3/NO$ molar ratio becomes better with decreasing the ammonia injection concentration and the size of nozzle diameter.

• Journal of the Korean Ceramic Society
• /
• v.43 no.4 s.287
• /
• pp.235-241
• /
• 2006

Mullite short fibers have been fabricated by adapting the Kneading-Drying-Calcination (KDC) process and characterized. The effect of the addition of foaming agent and calcination temperature on the formation of mullite fibers from coal fly ash, was examined. In the present work, ammonium alum $NH_4Al(SO_4)_2\;12H_2O$ synthesized trom coal fly ash and sodium phosphate $Na_2HPO_4\;2H_2O$ were used as foaming agents. After calcination at $1300^{\circ}C$ for 10 h and then etching with 20% HF solution at $50^{\circ}C$ for 5 h using a microwave heating source, the alumina-deficient $(AI_2O_3/SiO_2$ = 1.13, molar ratio) orthorhombic mullite fibers with a width of ${\sim}0.8mm$ (aspect ratio >30), were prepared from the coal fly ash with $AI_2O_3/SiO_2$ = 0.32, molar ratio by the addition of $NH_4AI(SO_4)_2\;12H_2O$, and with further addition of 2 wt% sodium phosphate. The excessive addition of sodium phosphate rather decreased the formation of mullite fibers, possibly due to the large amount of liquid phase prior to mullitization reaction.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.10 no.6
• /
• pp.494-499
• /
• 2005

The chemical, physical, and emulsifying properties of BSF-1, which is an extracellular lipopolysaccharide biosurfactant produced by Klebsiella oxytoca strain BSF-1, were studied. BSF-1 was found to be composed mainly of carbohydrate and fatty acids. The average molecular weight was $1,700{\sim}2,000 kDa$. The polysaccharide fraction contained L-rhamnose, D-galactose, D-glucose, and D-glucuronic acid at a molar ratio of 3:1: 1:1. The fatty acid content was 1.1 % (w/w) and consisted mainly of palmitic acid (C16:0), 3-hydroxylauric acid (3-OH-C12:0), and lauric acid (C12:0). In terms of thermal properties, BSF-1 was revealed to have inter- and intra-molecular hydrogen bonds. The hydrodynamic volume (intrinsic viscosity) of BSF-1 was 22.8dL/g. BSF-1 could be maintained as a stable emulsion for 48 h through a low-level reduction in surface tension. The optimal emulsification temperature was $30^{\circ}C$. Emulsification by BSF-1 was efficient at both acidic and neutral pH values.

• Clinical and Experimental Pediatrics
• /
• v.48 no.3
• /
• pp.298-305
• /
• 2005

Purpose : We performed this study to evaluate the mean serum levels of insulin-like growth factor (IGF)-I, insulin-like growth factor binding protein(IGFBP)-2 and IGFBP-3 in healthy Korean children according to age and sex. Methods : Ninety two healthy children, consisting of 42 boys and 50 girls, were classified into five groups according to age : neonate; infancy; early childhood; late childhood; and adolescence. We measured serum levels of IGF-I, IGFBP-2 and IGFBP-3 by enzyme-linked immunosorbent assay(ELISA) and analysed the serum levels according to sex and age group. Results : For boys, the mean serum levels of IGF-I(ng/mL) in neonate, infancy, early childhood, late childhood and adolescence were $41.1{\pm}3.6$, $70.9{\pm}33.7$, $103.5{\pm}97.2$, $89.8{\pm}46.5$ and $51.4{\pm}27.8$, respectively. Those of IGFBP-2(ng/mL) were $8.2{\pm}3.4$, $5.8{\pm}0.4$, $9.3{\pm}4.0$, $9.5{\pm}1.1$ and $7.0{\pm}0.5$, respectively. Those of IGFBP-3(ng/mL) were $559.2{\pm}215.2$, $1,333.3{\pm}692.5$, $2,254.6{\pm}1,513.8$, $2,447.1{\pm}1,464.2$, $1,533.6{\pm}807.4$, respectively. For girls, the mean serum levels of IGF-I(ng/mL) according to five age groups were $53.3{\pm}9.5$, $99.3{\pm}45.8$, $69.6{\pm}51.1$, $106.2{\pm}67.0$ and $145.1{\pm}127.8$, respectively. Those of IGFBP-2 (ng/mL) were $9.1{\pm}7.4$, $5.3{\pm}0.9$, $6.9{\pm}2.0$, $10.5{\pm}3.0$ and $7.9{\pm}1.3$, respectively. Those of IGFBP-3(ng/mL) were $858.2{\pm}433.4$, $1,834.8{\pm}851.3$, $1,404.3{\pm}570.2$, $2,203.5{\pm}899.4$ and $2,029.3{\pm}1,316.7$, respectively. There were significant positive correlations observed between IGF-I and IGFBP-3 levels(r=0.589, P=0.000). Conclusion : IGF-I and IGFBP-3 levels increased as children get older. The peak level of IGFBP-3 was observed in late childhood for both boys and girls, suggesting a current trend of children reaching peak growth velocity before adolescence. The IGFBP-2 level was higher in neonates compare to infancy, suggesting that IGFBP-2 is an important substance for fetal growth.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.12
• /
• pp.1409-1412
• /
• 1999

The spectrophotometric determination method of scandium with eriochrome cyanine R (ECR) and the composition ratio of the complex were investigated in the presence of surfactants. A volume of 5 mL of 1.0×$10^{-3}$ M ECR and 10 mL of 2.0×$10^{-4}$ M CTMAB are necessary for the determination of 1.0×$10 ^{-7}$ ~ 3.0×$10^{-6}$ M Sc(III) at pH 6.5. The apparent molar absorption coefficient of the Sc(III)-ECR-CTMAB, ternary complex at 610 nm is 5.6×$10^5$ $mol^{-1}cm{-1}$L and its detection limit is 1.0×$10^{-7}$ M. Separation studies were conducted by the column method. The effect of pH, elution solution and the influence of rare earth elements as interferents was discussed. Their separation was carried out in 0.1 M HCl-50% methanol solution and 1.0 M HCl media. The method was applied for the determination of Sc(III) in monazite.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.559-564
• /
• 2017

In this study, the optimization process was carried out by using the central composite model of the response surface methodology in waste cooking oil based biodiesel production process. The acid value, reaction time, reaction temperature, methanol/oil molar ratio, and catalyst amount were selected process variables. The response was evaluated by measuring the FAME content (more than 96.5%) and kinematic viscosity (1.9~5.5 cSt). Through basic experiments, the range of optimum operation variables for the central composite model, such as reaction time, reaction temperature and methanol/oil molar ratio, were set as between 45 and 60 min, between 50 and $60^{\circ}C$, and between 8 and 12, respectively. The optimum operation variables, such as biodiesel production reaction time, temperature, and methanol/oil molar ratio deduced from the central composite model were 55.2 min, $57.5^{\circ}C$, and 10, respectively. With those conditions the results deduced from modeling were as followings: the predicted FAME content of the biodiesel and the kinematic viscosity of 97.5% and 2.40 cSt, respectively. We obtained experimental results with deduced operating variables mentioned above as followings: the FAME content and kinematic viscosity of 97.7% and 2.41 cSt, respectively. Error rates for the FAME content and kinematic viscosity were 0.23 and 0.29%, respectively. Therefore, the low error rate could be obtained when the central composite model among surface reaction methods was applied to the optimized production process of waste cooking oil raw material biodiesel.

• Advances in Energy Research
• /
• v.4 no.3
• /
• pp.189-202
• /
• 2016

This work emphasized optimum production of biodiesel using non-edible Prunus armeniaca (Bitter Apricot) oil via transesterification collected from the high altitude areas of Himachal Pradesh, India. In this study the author produced biodiesel through the process of transesterification by using an alkali catalyst with alcohol (methanol and ethanol), under the varying molar ratio (1:6, 1:9, 1:12), variable catalyst percentage (1% and 2%) and temperature ($70^{\circ}C$, $75^{\circ}C$, $80^{\circ}C$, $85^{\circ}C$). Furthermore, a few strong base catalysts were used that includes sodium hydroxide, potassium hydroxide, sodium metal and freshly prepared sodium methoxide. After screening the catalyst, response surface methodology (RSM) in connection with the central composite design (CCD) was used to statistically evaluate and optimize the biodiesel production operation using NaOH as catalyst. It was found that the production of biodiesel achieved an optimum level biodiesel yield with 97.30% FAME conversion under the following reaction conditions: 1) Methanol/oil molar ratio: 1:6, 2) Reaction time: 3h, 3) Catalyst amount: NaOH 2 wt. %, and 4) Reaction temperature: $85^{\circ}C$. The experimental results showed that the optimum production and conversion of biodiesel through the process of transesterification could be achieved under an optimal set of reaction conditions. The biodiesel obtained showed appropriate fuel properties as specified in ASTM, BIS and En- standards.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.3
• /
• pp.317-322
• /
• 2021

Silicon (Si) has been considered as a promising anode material because of its abundant reserves in nature, low lithium ion (Li⁺) intercalation/de-intercalation potential (below 0.5 V vs. Li/Li⁺) and high theoretical capacity of 4200 mA h/g. In this paper, we prepared a silicon-based (Si-based) anode material containing a small amount of silicon carbide by using magnesiothermic coreduction of silica and hexachlorobenzene. Because of good conductivity of silicon carbide, the cycle performance of the silicon-based anode materials containing few silicon carbide is greatly improved compared with pure silicon. The raw materials were formulated according to a silicon-carbon molar ratio of 10:0, 10:1, 10:2 and 10:3, and the obtained products were purified and tested for their electrochemical properties. After 1000 cycles, the specific capacities of the materials with silicon-carbon molar ratios of 10:0, 10:1, 10:2 and 10:3 were still up to 412.3 mA h/g, 970.3 mA h/g, 875.0 mA h/g and 788.6 mA h/g, respectively. Although most of the added carbon reacted with silicon to form silicon carbide, because of the good conductivity of silicon carbide, the cycle performance of silicon-based anode materials was significantly better than that of pure silicon.

• Korean Journal of Food Science and Technology
• /
• v.19 no.4
• /
• pp.285-289
• /
• 1987

The partition behavior or proteins in an aqueous two-phase system of poly (ethyleneglycol)-potassium phosphate buffer (PEG/PPB) was investigated. The proteins of different surface hydrophobicity, i.e. Bovine serum albumin (BSA), ${\beta}-lactoglobulin$, ovalbumin. moved to the PPB-rich bottom phase in a PEG(12%)/PPB (12%) two-phase system resulting in very low partition coefficients. When the concentration of PPB increased to 15% level. the electric potential of bottom phase changed from +50 mV to zero and the partition coefficient tended to increase. The change In the molar ratio of $K_2HPO_4/KH_2PO_4$ in PPB from 1.43 to 9.55 caused the volume ratio of top to bottom phase $(V_t/V_b)$ to be decreased and protein partition coefficient increased. When the concentration of PPB was elevated from 14% to 26%, the $V_t/V_b$ decreased from 1.5 to 0.39 and the partition coefficient of proteins increased drastically; ${\beta}-lactoglobulin$ 74 fold. BSA 32 fold, ovalbumin 12 fold and lysozyme 5 fold.

• Nutritional Sciences
• /
• v.1 no.1
• /
• pp.8-15
• /
• 1998

In order to independently examine the effects of long-chain saturated fatty acids and dietary cholesterol levels on plasma and hepatic cholesterol concentrations, six different diets were fed to male Mongolian gerbils (14 gerbils pes grcup) for an 8-week period. Purified diets contained 36% energy as fat (each saturated fatty acid tested comprised about 20% of the total fat energy) and 0.06% (w/w) cholesterol, corresponding to typical human consumption patterns in Western diets. Fat blends were formulated with natural fat sources. To determine the effects of different saturated fatty acids on plasma and liver cholesterol levels, four of the six diets contained constant levels of all nutrients except for the amounts of lauric acid (12 0), myristic acid (14 : 0), palmitic acid (16 0), and stearic acid (18 : 0). Dietary cholesterol effects were tested using 16 : 0-enriched diets containing 0, 0.006, and 0.06% (w/w) cholesterol. None of the plasma lipids were influenced by fatty acid treatment, including triglycerides, plasma total-, VLDL+LDL-, and HDL-cholesterol. However, hepatic esterified cholesterol concentrations were increased in the palmitic and stearic arid diet groups compared to the lauric and myristic acid diet group. The molar ratios of hepatic EC/FC were the highest in the palmitic acid diet (12.2 $\pm$0.6) and the lowest in the myristic acid diet (6.4$\pm$0.2). Dietary cholesterol significantly (p<0.001) increased the plasma total cholesterol which was due to the increase of both HDL-and VLDL+LDL-cholesterol. In the absence of dietary cholesterol and compared to other species, the gerbil exhibited a high molar ratio of hepatic EC/FC, which was funker elevated by dietary cholesterol feeding (0.06%). The results from this study indicate that hepatic cholesterol concentrations are sensitive to both low levels of dietary cholesterol and saturated fatty acid chain length and also, that plasma cholesterol concentrations are sensitive to low levels of dietary cholesterol .