• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.97-103
• /
• 1997

Effects of fuel injection timing on the lean misfire limit of a sequential MPI SI engine has been investigated. To investigate the interaction of injection timing and intake flow characteristics, so called axial stratification phenomena, 4 kinds of different intake swirl port of the same combustion chamber geometry have been teated in a single cylinder engine test bench. And 2 kinds of fuel, gasoline and compressed natural gas(CNG), were used to see the effect of liquid fuel vaporization. Result shows that combination of port swirl and injection timing governs the lean misfire limit and lean misfire limit envelopes remain almost the same for a given ratio regardless of engine speed. It is also found that two phase flow has some effects on lean misfire limit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.47-55
• /
• 1998

A new ignition system concept was developed to improve ignition performance, accuracy of control and the reliability of the ignition system. The new ignition system has ho호 frequency discharge characteristics with 1.5-2.0 ms discharge duration, in place of the usual solitary longer duration event. We applied the system to a commercial engine to study its influence on the maximum combustion pressure attained during the cycle, when this peak pressure occurred, imep, variation rate of the engine speed and the flammability limit of a lean mixture. In this study, we clarified that the new ignition system had a beneficial effect of the lean mixture flammability limit. Also for a given mixture strength we found that the mew ignition system gave a higher peak cylinder pressure than in the case of the conventional ignition system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.7-12
• /
• 2003

Mixture formation in the cylinder of a lean bum engine has been observed by Laser Induced Fluorescence technique. XeCl laser (308nm) was used to produce a laser sheet. 3-pentanone has been added to iso-octane fuel to produce fluorescence, the intensity of which is proportional to the concentration of the fuel. The laser sheet was introduced through the piston window and the fuel distribution in the vertical plane was observed through a side window. Comparison has been made for the cases of selected fuel injection timing as 0, 360, 405, and 450 CA. For the case of 0 and 360 CA injection, uniform fuel distribution in the combustion chamber has been obtained at the ignition time which is favorable for the high load mode. And the late injection cases, 405 and 450 CA, revealed the stratified formation of rich mixture around the spark plug. That extends the lean misfire limit and reduces cyclic variation in the low load mode.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.40-49
• /
• 2016

This study aims to confirm the characteristics of low swirl combustion at our low swirl model combustor. To do it, it is experimentally conducted by evaluating the flame shape, stability region and emissions according to the swirl angle. The most significant feature of low swirl combustion is a occurrence of lifted flame. Such lifted flames happen to combine exquisitely propagating feature of premixed flame with diverging flow. This feature of lifted flame was confirmed through a velocity flow field and visualized the flame in this model combustor. The visualized flame was classified according to the thermal power and equivalence ratio. The variation study in swirl angles showed that the lean flammable limit could be extended only by swirl angles. Also, as the swirl angle increased, it was confirmed that the NOx and CO emissions were decreased due to the mixing enhancement and shorter resident time.

• Journal of the Korean Institute of Gas
• /
• v.14 no.4
• /
• pp.12-17
• /
• 2010

Natural gas is one of the most promising alternatives to gasoline and diesel fuels because of its high thermal efficiency and lower harmful emissions, including $CO_2$. However, the possibility of partial burn and misfire makes the benefits of natural gas fueled engine worse under lean burn operation condition, Hydrogen addition can promote the combustion characteristics while reduces emissions extremely. In this study, the effect of hydrogen addition on an engine performance was investigated. The results showed that thermal efficiency was increased due to the expansion of lean operation range under stable operation. NOx emission can be significantly reduced with the small increase in HC or CO emissions.

• Journal of Power System Engineering
• /
• v.16 no.5
• /
• pp.5-12
• /
• 2012

희박예혼합기의 급속연소에 관한 연구를 위하여 2-실린더 가솔린 엔진을 부실 타입의 압축천연가스(CNG) 분사 엔진으로 개조하였다. 본 연구에서는 부실의 최적설계에 관심을 두고 두 종류의 부실을 적용하여 실험을 실시하였고, 부실의 체적과 홀 개수는 1.5cc와 6개로 각각 동일하게 하고, 홀 직경을 0.8mm 및 1.1mm로 달리하였다. CNG연료는 포트연료분사(Port fuel injection; PFI)와 부실분사(Sub-chamber injection; SCI)에 의해 엔진에 독립적으로 공급되고, 그 실험결과로 구한 연소압력, 평균유효압력(IMEP), 질량연소분율과 사이클변동계수(COV) 등을 서로 비교하였다. 본 연구의 대표적 실험연구결과로서 PFI 타입의 엔진연소특성은 희박예혼합기의 경우를 제외하고 모든 조건에 있어서 기존의 가솔린 엔진과 비슷하였고, SCI 타입의 엔진연소특성으로 평균유효압력은 부실 내에 불완전 예혼합기형성으로 PFI 타입보다 낮았으며, COV는 SCI 타입이 희박가연한계가 확대됨으로 인하여, 특히 높은 공기과잉률 범위에서 PFI 타입과 비교해 보다 좋은 결과를 나타내었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.37-44
• /
• 1998

Lean burn combustion is an important concept for improving the fuel consumption and exhaust emissions. However, the lean burning is associated with increased cycle-to-cycle combustion variations due to the ignition instabilities and redu- ced flame propagation rates. Engine stability under lean mixture conditions could be improved by increasing flame speed through enhanced flow characteristics and by securing ignitability with improvement of ignition systems. The effects of flow motion and ignition characteristics on the combustion performances were investigated in a 4-valve SI engine. Flow motions of tumble-swirl were varied with a swirl control valve attached at the inlet ports, while ignition energy and its distribution were controlled in a high -frequency ignition system by changing spark duration and spark frequency. The improvement of lean burn performance by the optimum flow motion and ignition characteristics is discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.3
• /
• pp.302-310
• /
• 1997

In this paper, we find a method to improve ignitability using methanol which is prospective as an alternative fuel. The constant volume combuster is divided into main chamber and sub-cham¬ber. These two chambers are linked by an adapter which is shaped like a cup. We also compare CDI to HIS that is revised in our laboratory for making a scrutiny into the effects of ignition char¬acteristics. Besides, we analyze a flame propagation process in the main and sub-chamber through taking pictures 10, 000 frames per second by high speed camera at the state being fabricated quartz glass aside main and sub-chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.148-156
• /
• 2014

This study is a follow-up study of "Development of Plasma Ignition System" was presented at the 2013 KSAE spring conference. This study compares lean limit of conventional ignition system with plasma ignition system on constant volume combustion test & Engine Combustion test.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.24-31
• /
• 2023

In this study, characteristics of a propane-air premixed flame sin DC electric field was investigated. The stainless steel Bunsen burner and the stainless steel ring were used as electrode, and the high voltage supply was used for applying electric field. Flammability range increased significantly when the positive voltage was applied because of extension of LBO limit, while it shrank when the negative voltage was applied. The reason for this was not much related to the burning velocity, but the induced flow around the burner by electric field. withNOx production slightly increased after positive voltage was applied in identical equivalence ratio. Nevertheless, it was advantageous to apply the positive electric field to reduce the NOx since the extension of LBO limit makes the burner possible to operate in very low equivalence ratio.