• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2012-2017
• /
• 2003

This paper reports on the influence of blade surface roughness on turbine efficiency. The performance of a low speed one-stage axial turbine with roughened blade surfaces was evaluated. Sandpaper with equivalent sandgrain roughness ($k_s$) was used to roughen the blades. Efficiency (${\eta}/{\eta}_0$) decreases by 4.5 % with sandgrain size of 400 ${\mu}m$ on the stator suction surface.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.07a
• /
• pp.310-315
• /
• 2002

겨울철 저온기에 온실의 작물재배는 많은 에너지가 소요되어 저온기의 에너지비용을 최소화하는 것이 온실의 운전비용의 절감과 이용효율이 증대되어 농가소득을 높일 수 있다. 저온기에는 작물의 수확량이 적정 온도조건의 80%수준으로 최소 에너지 투입방법 기술을 개발하여 수확량을 증대시킬 필요가 있다. 기존의 난방방법인 온수보일러는 온도유지 안정성은 좋으나 시설비용이 많이 들고 온풍난방은 설치비용은 저렴하나 온도 유지안정성이 다소 떨어지는 단점이 있다. (중략)

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.14-14
• /
• 2000

가스터빈 연소기의 연소 효율을 높이기 위해서는 연료와 공기의 충분한 혼합이 필요하다. 연료와 흡입되는 공기의 혼합은 큰 스케일의 난류 성분보다는 오히려 연소기내에서 국부적으로 작용하는 작은 스케일의 난류 성분에 크게 지배를 받게된다. 이러한 혼합 촉진을 위해 연료와 공기의 경계면에서의 운동에너지를 증가시키는 방법은 압력의 손실을 가져오게 되지만 혼합의 촉진에 의한 완전연소와 저 NOx화는 더 큰 이익을 가져다 준다.(중략)

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.9
• /
• pp.495-504
• /
• 2017

An amphibious scrubbing/suction dredging machine with cylindrical rotating brush, housing, and turbidity barrier was newly-developed to remove both sediments with about 10 cm thickness and periphyton attached on various structures in urban water-circulating systems through the scrubbing, suction, and dredging processes. Based on the field application and long-term monitoring, the increase in both suspended solids (SS) and turbidity of water during the scrubbing, suction, and dredging processes was negligible (p>0.05). In some cases, the turbidity of water initially increased, however, the turbidity was stabilized within 20 minutes from the start of dredging processes. The concentration changes in TN and TP of water were not statistically different (p>0.05) before and after the scrubbing, suction, and dredging processes, indicating that benthic nutrients released from sediments were not significantly diffused, and were not supposed to cause significant water pollution. Also, water treatment facilities along with an amphibious scrubbing/suction dredging machine could be more effective since the removal of contaminant loadings through the scrubbing, suction, and dredging processes was much greater than that through simple coagulation/precipitation processes. Finally, GPS-based realtime tracking and operation program have been developed and applied in various urban water-circulating systems, and development of driver cooperative autonomous driving system is in progress to eliminate the need for manual driving of an amphibious scrubbing/suction dredging machine.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.4944-4949
• /
• 2012

The purpose of this paper is concerned with a development of air gun for use at work. A air gun is the tool to remove of cutting fluid and workpiece chip in industrial field used machine tool. And it generally is used to shoot a jet of compressed air. Worker must prepare respectively air gun for suction and shooting a jet of compressed air. Therefore we has developed new air gun. In this paper we research for design and analysis of it. The air gun is composed of body, pipe, opening and shutting unit, turning unit, air tube and elements for fabrication. The developed air gun is experimented to confirm the efficiency.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.5-11
• /
• 2008

산업공정에서 널리 사용하는 반응기는 성질이 상이한 물질을 혼합하는 시스템으로서 본 연구에서는 이젝터(ejector)에 의한 반응기의 개발을 수행하였다. 액체-가스 이젝터는 구동유체에 의하여 기체가 흡입되면서 각종 유해가스를 제거하는 목적 또는 기체와 액체의 혼합 등 목적으로 사용된다. 본 실험에서 액체구동 가스혼합반응기의 실험 장치를 구축하고 이젝터 내부의 유동패턴과 기체용해도 자료를 도출하며 고효율 이젝터 설계를 위한 진공도 측정과 디퓨저 각도가 다른 이젝터의 실험 및 수치해석을 수행하였다. 이젝터의 성능은 흡입 측에서의 진공압력으로 평가되며 이 진공압력은 이젝터의 노즐 설계 및 유동조건에 의하여 결정되므로 이에 대한 기본적인 특성 도출이 선결되어야 한다. 순환유체의 유량이 70LPM, 80LPM 90LPM조건에서 두 가지 디퓨저에 대하여 비교실험을 수행하였다. 실험적 연구와 수치해석연구를 통하여 혼합성능과 이젝터의 내부유동특성에 대하여 고찰한 결과 디퓨저의 각도가 5.0도일 때 진공도가 더욱 높으며 구동액체의 유량이 작을 때는 진공도차이가 크지만 유량이 증가함에 따라 진공도 차이가 감소된다. 구동액체의 유량이 증가할수록 용존산소농도는 증가하며 디퓨저의 각도가 5.0도일 때는 용존산소 농도가 더 높게 나타나는 것을 확인할 수 있었다.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.15-23
• /
• 2004

In order to investigate efficiency and flowfield charateristics of the intake-diffuser for the ship waterjet propulsion, new experimental verification technology was set up in the cavitation tunnel. 1-hole and 5-hole pilot tubes were designed and manufactured to measure the pressure and velocity distributions at intake-diffuser entrance and impeller inlet. The calibration of the 5-hole pilot tubes is conducted at the cavitation tunnel The cavitation inception occurs at the intake lip, and the occurrence position depends on IVR (Inlet Velocity Ratio) condition. The present experimental device will be applied sufficiently for the development of the design and performance improvement technologies.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.2
• /
• pp.191-199
• /
• 2014

Effects of design variables on the performance of a double-inlet centrifugal blower have been analyzed based on the three-dimensional flow analysis. Two design variables, blade inlet and outlet angles, are introduced to enhance a blower performance. General analysis code, ANSYS-CFX13, is employed to analyze internal flow and a blower performance. SST turbulence model is employed to estimate the eddy viscosity. Throughout the shape optimization of an impeller at the design flow condition, the blower efficiency and pressure are successfully increased by 4.7 and 1.02 percent compared to reference one. It is noted that separated flow observed near cut-off region can be reduced by optimal design of blade angles, which results in stable flow pattern in the blade passage and increase of a blower performance. The stable flow at the impeller also makes good effects at the outlet of a volute casing.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.522-525
• /
• 2008

A vacuum cleaner is the widely used home equipment. However, it has a trouble with too much power consumption. Most losses occur at the centrifugal fan. To remedy this trouble the investigation of motor, which is the main component of vacuum cleaner, is required. The flow characteristics around the high-speed rotating centrifugal fan which is influenced by the very low inlet pressure is quite different from a commonly used fan. Hence it is quite difficult to analyze the flow by the experimental means or by the numerical simulation. In this research, it is aimed to improve the air-suction performance of a vacuum cleaner through the flow analysis around a motor. The efficiency of the centrifugal fan is affected by blade shape, blade number, blade pitch, etc. The influence of the shape of impeller on the flow is investigated in this study. The flow around the centrifugal fan is simulated by applying the moving mesh. To verify the validity of the computation results, the air flow rate and the pressure field to the cleaner is compared with the experimental data. All simulations are performed by using commercial code SC/Tetra. The calculated results show good agreement with the experimental ones and it is believed to be promising to use computational simulation in the improvement of the vacuum cleaner performance.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.21-30
• /
• 1997

This paper describes the experimental method of a pod-type waterjet propulsion system in a towing tank and shows the experimental analysis and test results of a designed waterjet propulsion system to be used for a hybrid high speed craft. The cruising performance of this craft is estimated from the results of the hull resistance test and waterjet test under the assumption that the interaction between the hull and the inlet pod is very small. A pod-type waterjet system with an axial pump was designed and a stand-alone waterjet experimental system was developed. Useful data such as the pump performance, the jet efficiency, the losses of inlet duct and nozzle were obtained. Test results show a good agreement with the design requirement.