• Journal of Embryo Transfer
• /
• v.20 no.1
• /
• pp.55-62
• /
• 2005

This study was undertaken to access the effect of collection methods on the collection efficiency, blastocyst rate and pregnancy rate after IVP embryo transfer. The ovaries of Hanwoo were obtained from an abattoir and kept on 25 to $28^{\circ}C$ and transported to laboratory within 4 hrs. The oocytes were collected by aspiration of follicles $(2\~6\;mm)$ with or without slicing of ovaries after aspiration. The oocytes were matured in vitro (IVM) for 20 to 24 hrs in TCM-199 supplemented with $10\%$ fetal bovine serum at $39^{\circ}C$ under $5\%\;CO_{2}$ in air. Following routine IVM/IVF procedure, the oocytes and presumed zygotes were cultured for three day in CRlaa medium with BSA. The cumulus cells at 2 to 8-cell stage of embryos removed then the embryos and were cultured in CRlaa medium containing $10\%$ fetal bovine serum in $5\%\;CO_{2}$ at $39^{\circ}C$. The fresh blastocysts cultured for 7 to 9 days were transferred into recipients. The numbers of oocytes recovered form two different methods, the aspiration and slicing after aspiration, were compared to know what. The number of oocytes per ovary was 8.2 and 6.5 in aspiration combining slicing, and aspiration groups, respectively (p<0.05). The cleavage rate in aspiration method are significantly (p<0.05) high than those in slicing post aspiration $(27.9\%)$, and aspiration $(25.5\%)$. The pregnancy .ate in aspiration method $(62.5\%)$ was high than that in slicing method after aspiration $(54.4\%)$. The pregnancy rates of aspiration method and slicing method after aspiration in nullipara $(58.1\%\;vs\;68.2\%)$ was high than that in pluripara $(49.5\%\;vs\;53.2\%)$. The results obtained that the increased number of oocytes per ovary in slicing method after aspiration could be better than that in aspiration method. Pregnancy rate in aspiration method was slightly higher in than that in slicing method after aspiration.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.5
• /
• pp.387-395
• /
• 2015

A technique for calculating the additive drag of the inlet in supersonic flow was studied using commercial CFD software, STAR-CCM+, which provides a efficient way of 3 dimensional flow analysis with polyhedron-shaped grid system. Three configurations were chosen and applied to the calculation with various flow conditions of two different free stream Mach No. and some mass flow ratios. Comparisons with results from wind tunnel test gave good agreements. Though computation were carried out with the inviscid and compressible flow around the supersonic inlet for the supercritical condition, ignoring the viscous effects is concluded to give little effects on the accuracy of the additive drag calculation and to make the calculation more efficient owing to less effort and time consumed for grid system build-up and for iteration because of less grid number and simpler boundary condition.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.18 no.3
• /
• pp.77-86
• /
• 2010

In this study, the model of the indirect wind suction waste sorting machine for characteristics of the screening of waste was studied using computational fluid dynamics and the drag coefficient for the model and the suction wind speed were obtained. The wind separator are developing by installing a cyclone air outlet to the suction blower impeller waste is selective in a way that does not pass the features and characteristics of the inlet pipe of the pressure loss and separation efficiency can have a significant impact on. Using Wind separator for selection of waste in the waste prior research on the aerodynamic properties are essential. For plastic cases, it is reasonable to take the drag coefficient between 0.8 and 1.0, and for cans, compression depending on whether the cans, the drag coefficient is in the range from 0.2 to 0.7. The separation efficiency of waste as change suction speed was the highest efficiency when the suction speed was 25~26 m/s. Shape of the inlet, depending on how the transfer pipe of the duct pressure loss occurs because the inlet velocity changes through the appropriate design standards to allow for continued research is needed.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.122-128
• /
• 2011

A series of water tests of a Lox pump for liquid rocket engines are performed at a room temperature. According to the hydraulic test results, the head coefficient is slightly decreased when the rotational speed of the pump is increased. However the efficiency is high at the high-speed test. Also, according to the cavitation test results, the cavitation performance of the pump is found to be decreased when the flow ratio is less than 92%. Furthermore, the vibration characteristic is analyzed using measured high frequency data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.115-121
• /
• 2017

The efficiency of railway track cleaning vehicle for eliminating fine particulate matter (PM10 and PM2.5) in a subway tunnel depends strongly on the structure of the air blowing and suction system installed under the train. To increase the efficiency of underbody suction system, this paper proposes a novel method to use the Coanda effect for the air blower and dust suction module. In particular, through Computational Fluid Dynamics (CFD) analysis, the flow control device induced by the Coanda effect enables an increase in the overall flow velocity and to stabilize the flow distribution of the suction module at a control angle of $90^{\circ}$. In addition, the flow velocity drop at the edge of the air knife-type blower can be improved by placing small inserts at the edge of the blower. Those 4 modular designs of the dust suction system can help remove the dust accumulated on the track and tunnel by optimizing the blowing and suction flows.

• Journal of Power System Engineering
• /
• v.16 no.1
• /
• pp.44-50
• /
• 2012

팁 간격의 크기가 냉각탑용 축류팬의 성능과 누설 유동에 미치는 영향을 조사하기 위해서 서로 다른 2가지 팁 간격을 가진 경우에 대해서 점성유동을 해석하였다. 케이싱 내에서 작동하는 축류팬 주위의 유동을 연속방정식, Navier-Stokes 방정식 등을 지배방정식으로 사용하여 수치해석 하였다. 난류유동에 나타나는 레이놀즈 응력은 ${\kappa}-{\epsilon}$ 난류모델을 사용하여 계산하였다. 전체적으로 H형 격자계를 사용하였으며, 팁 주위의 유동을 해석하기 위해서 팁 영역 주위에 부분적으로 조밀한 격자를 두었다. 팁 간격이 증가하면 누설 유동의 증가로 인한 유동 손실의 증가로 전압상승과 수력효율이 감소하였다. 팬 직경에 대한 팁 간격이 0.4%에서 1.0%로 증가하면 전압상승 값이 약 10% 정도 감소하였으며, 수력효율은 약 3% 정도 감소하였다. 팁 간격이 팁 근처 날개 주위의 압력에 미치는 영향을 보면, 팁 간격이 증가하여 누설 유동이 증가하면 흡입면과 압력면의 압력차가 전연 부근에서 감소함을 알 수 있었다. 누설 와류의 중심은 코드를 따라서 흡입면으로 부터 떨어져 나가면서 형성됨을 알 수 있었다. 누설 와류의 위치를 보면 팁 간격이 증가하면 와류 중심의 위치가 흡입면 쪽으로 이동하고, 흡입면에서 떨어진 거리도 날개 후반부에서 증가 폭이 커지는 포물선 형태로 증가함을 알 수 있었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.29-33
• /
• 2005

In the fuel of the solid fuel ramjet there are metal particles in order to improve the Isp like as solid rocket propellants. Because of the short combustion residence time these metallized fuels have low combustion efficiencies. Therefore it is necessary to increase the combustion efficiency and the inlet air temperature does an important role to this. The effect of the inlet air temperature to the performance is investigated through the semi-empirical method by adopting the experimental combustion efficiency. There are two factors to affect the inlet temperature, free stream temperature and the flight Mach number.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.271-274
• /
• 2007

In the fuel of the solid fuel ramjet there are metal particles in order to improve the Isp like as solid rocket propellants. Because of the short combustion residence time these metallized fuels have low combustion efficiencies. Therefore it is necessary to increase the combustion efficiency and the inlet air temperature does an important role to this. The main factors to affect the inlet air temperature is the free stream temperature and the flight Mach number. Also the flow velocity in the combustor does an important role, therefore entire range of the air flow; from the stagnation to the sonic velocity in the ramjet combustor is considered.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.1-13
• /
• 2007

Scramjet engine is one of the most promising propulsion systems for future transport. For the ground test with T4 shock tunnel, model scramjet engine is designed. Design flight Mach number is 7.6 and flight altitude is 30km. Engine intake is designed by Levenberg-Marquardt optimization method and Korkegi relation. Furthermore, cowl cut out region is installed by the rule of Kantrowitz limit. Inside the combustor, cavity type flame holder is installed. Cavity is designed by Rayleigh line relation and PSR model. Numerical analysis is performed for the design confirm.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.59-59
• /
• 2002

램제트 추진기관은 압축과정을 별도의 부품 없이 형상에 의해서 감속하여 연소 압력비를 얻는다. 따라서 구동 마하수와 형상에 의해 흡입과정의 압축 효율이 결정된다. 설계점은 충분한 유량을 확보 할 수 있는 유량과 충격파 각을 조절하여 전압력 손실을 줄이도록 고려되어야 한다. 또한 연소가 일어나면 연소실 압력이 배압으로 작용하고 비행시에 받음각은 변하므로 이에 따른 성능 분석도 고려 되어야 할 사항이다. 본 연구는 국내에서 실험한 형상에 대해 수치계산을 수행하여 코드의 검증과 아울러 램제트 유동장의 수치적 시뮬레이션도 설계단계에서 하나의 도구로 이용할 수 있음을 보여준다. 실험에서는 배압 조건을 얻기 위해 유동 블록키지를 유로 내에 두어 상응하는 배압을 얻었지만 본 계산에서는 압력 경계조건을 직접 사용하였다. 유동이 비정상 특성을 가지므로 시간 정확도를 이차로 가지도록 이중시간 전진법을 사용하였다. 사용한 압력비는 충격파가 카울 끝에 닿는 임계상태에 가까운 12, 13, 14에 대해 계산을 수행하였고 부스터모드로 흡입구 끝이 막혀 있다가 램제트 모드로 바뀌어 연소실 압력이 위의 압력비라고 가정할 때의 비정상 천이 과정을 계산해 보았다. 본 계산은 흡입구 부분만을 떼어놓고 적절한 가정 하에 수행되었지만 연소실 내부도 비정상 특성을 가지므로 흡입구와 연소실을 동시에 같이 계산해야한다. 추후에 전체적인 계산을 진행하기 위한 전 단계로 흡입구 계산만을 수행하여 실험과 잘 일치하는 계산 결과를 얻었고 전체 계산을 위한 연구는 진행 중에 있다.