• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.1
• /
• pp.128-135
• /
• 2011

In this study, in order to develop ultra rapid hardening mortar(URHM) for tunnel repairs using bottom ash of low recycle ratio and Admixture as Eco concept, fundamental properties of URHM on temperature condition of construction field were performed. Test result, URHM of three types for fluidity and setting time were as in the following : B > C > A. Those for low temperatures were later than the standard condition. Compressive, bending and bond strength were similar with three types as follow. In compressive strength, initial strength of the low were smaller than the standard but the low in the long-term were similar with the standard. On the contrary to this, bending strength were similar in initial strength but the low in the long-term were smaller than the standard. The low in bond strength was average 35% less than the standard. Length changes was as in the following : A > C > B. the low is two times much as the standard but the case using blast furnace slag particles noticeably reduced length changes. Water absorption coefficient and water vapor resistance were as in the following : C > A > B. In case of URHM added bottom ash, water absorption coefficient and water vapor resistance were increased because bottom ash is porous material.

• Journal of Radiation Protection and Research
• /
• v.29 no.2
• /
• pp.73-90
• /
• 2004

The Reg. Guide 1.109 model was reviewed against its applicability to calculating radionuclide concentrations in agricultural products for operating nuclear facilities and an improved method was proposed. The model was so modified that the radionuclides deposited since the start of operation could be considered in assessing the root uptake. Translocation factors were introduced in the equation for calculating the concentrations in edible parts due to direct plant deposition. Values specific to Korea were set up for the input parameters of the modified model. The concentrations of $^{54}Mn,\;^{60}Co,\;^{90}Sr\;and\;^{137}Cs$ in rice seeds, Chinese cabbage and radish root were calculated for various hypothetical deposition histories using the Reg. Guide 1.109 model and the modified model with parameter values in the guide and those specific to Korea put in alternately. Through comparisons among the results, it could be expected that the use of the modified model with the input of parameter values specific to Korea would result In a more resonable and realistic assessment.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.4
• /
• pp.377-383
• /
• 2013

This study examined the radiopacity of eight contemporary luting cements by direct digital radiography. Five disc-shaped specimens ($5mm{\times}1mm$) were prepared for each material tested (BisCem, Clearfil SA Luting, Duolink, Maxcem Elite, Multilink Speed, Panavia F 2.0, RelyX Unicem Clicker, V-link). The specimens were radiographed using a Kodak CS 7600 image plate (Carestream Health, Inc., Rochester, NY, USA) and an aluminum step wedge with a range of thicknesses (1.5 to 16.5 mm in 1.5 mm increments) and a 1 mm tooth used as a reference. A dental X-ray machine Kodak 2200 Intraoral X-ray System (Carestream Health, Inc., Rochester, NY, USA), operating at 70 kVp, 4 mA, 0.156 s and a source-to-sample distance of 30 cm, was used. According to international standards, the radiopacity of the specimens was compared with that of an aluminum step wedge using NIH ImageJ software (available at http://rsb.info.nih.gov/ij/).The data was analyzed by ANOVA and a Tukey's post hoc test. Maxcem Elite (5.66) showed the highest radiopacity of all materials, followed in order by Multilink Speed (3.87) and V-link (2.83). The radiopacity of Clearfil SA Luting (1.35), BisCem (1.33), Panavia F 2.0 (1.29) and Duolink (1.10) were between enamel (1.79) and dentin (0.19). RelyX Unicem Clicker (0.71) showed the lowest radiopacity, which was higher than that of dentin. All materials showed a radiopacity above the minimum recommended by the International Organization for Standardization and the American National Standards/American Dental Association with the exception of RelyX Unicem Clicker.

• Journal of the Korean Chemical Society
• /
• v.29 no.3
• /
• pp.233-238
• /
• 1985

The non-porous and porous polystyrene divinylbenzene copolymers were prepared by the suspension polymerization method. The non-porous aminated polystyrene divinylbenzene, N-APSTDVB and the porous aminated polystyrene divinylbenzene, P-APSTDVB of 50∼100mesh size weakly basic anion exchanger were synthesized by chloromethylation followed by amination with methylamine. The functional groups of these synthesized anion exchangers were confirmed by their infrared spectra. The maximum capacity of these exchangers was 4.86meq/g. Pore volume and pore spectra were determined with a mercury porosimeter. The pore volume of P-PSTDVB increased with increasing X$_{diluent}$ at 30% of divinylbenzene. However, the pore volume of P-PSTDVB increased with increasing volume percent of divinylbenzene at constant mole fraction of diluent, X$_{diluent}$ of 0.5. The pore volume of synthesized copolymer and anion exchanger at 8% divinylbenzene and 0.5X$_{heptane}$ decreased as follows; P-PSTDVB 〉P-APSTDVB 〉N-PSTDVB. This result was attributed to the possibility that the pore volume were reduced by amination reactions. The distribution coefficients of boric acid on the N-APSTDVB anion exchanger in various concentrations of alcohol water solutions showed that as alcohol concentration increased, the distribution coefficients values decreased due to the reduced concentration of H$_2$BO$_3^-$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.896-901
• /
• 2002

Since many process parameters of FHD(Flame Hydrolysis Deposition) are involved in forming multi-component amorphous silica film ($SiO_2-B_2O_3-P_2O_5-GeO_2$), it has not been easy to predict the optical, mechanical and thermal properties of deposited film from the simple process parameters, such as source flow rate. Furthermore, the prediction of final composition of film becomes even more difficult after sintering at high temperature due to the evaporation of volatile dopants. The motivation of the study was to clarify the quantitative relationship between simple process parameters such as the flow rate of source gases and resulting chemical composition of sintered film. Hence, the compositional analysis of silica soot by FTIR(Fourier Transformation Infrared Spectroscopy) and ICP-AES(Inductively Coupled Plasma-Atomic Emission Spectrometry) under the control of the amount of dopant was carried out to obtain the quantitative composition. By measuring spectrum of absorbance from FTIR, the compositional change of B-O, Si-O, OH($H_2O$) in silica film was measured. The concentrations of these dopants were also measured by ICP-AES, which were compared with the FTIR result. The final quantitative relationship between simple process parameters and composition was deduced from the comparison between two results.

• Analytical Science and Technology
• /
• v.29 no.4
• /
• pp.179-185
• /
• 2016

An effective analytical method has been developed for the determination of β-blockers(atenolol, metoprolol and propranolol) and 6 β-lactams(amoxicillin, penicillin G, cefaclor, cefadroxil, cephalexin and cephradine) in water samples using two different cartridges. The samples were extracted by solid-phase extraction (SPE) with the usage of polymeric hydrophile-lipophile balance(HLB cartridges) and strong cation-exchange mixed-mode polymeric sorbent (MCX cartridges). A XDB-C₁₈ column(1.8 μm; 3.0 mm × 100 mm) was used for the sufficient chromatographic resolution. The calibration curves showed good linearity with high correlation coefficients (>0.995). The method detection limits (MDL) and the limits of quantification(LOQ) were from 1.1 to 3.9 ng/L and from 5 to 13 ng/L, respectively. The method was applied for the determination of the target compounds in tributaries and raw water of the Han River and these were found at N.D. to 0.209 μg/L.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.96-96
• /
• 2000

화학증착법으로 증착된 다이아몬드 박막은 우수한 전기적 특성과 뛰어난 화학적, 열적 안정성 때문에 전계방출소재로 많은 관심을 불러 일으키고 있다. 다이아몬드 박막의 전계방출은 저전계에서 일어나는 것으로 알려져 있으며, 저전계방출의 원인을 규명하려는 많은 연구가 진행되어 왔다. 한편, 다이아몬드 박막의 전계방출전류는 금속기판의 사용에 의한 기판/다이아몬드 접촉의 개선, 다이아몬드 박막내의 흑연성분의 조절에 의한 구조변화, 보론이나 인 (P), 질소의 도핑, 수소 플라즈마나 cesium 등의 금속을 이용한 표면처리 등의 여러 방법에 의하여 향상된다는 것이 입증되었다. 그 외에 메탄과 대기 분위기 처리, 암모니아 분위기에서의 레이저 조사도 전계방출특성을 향상시키는 것으로 보고되었다. 그러나, 다이아몬드 박막의 성장후 구조적 특성이 다른 박막의 후성장이나 열분해된 운자수소 처리가 다이아몬드 박막의 전계방출특성에 미치는 영향에 관한 연구는 지금까지 이루어지지 않았다. 본 연구에서는 수소처리와 후성장이 다이아몬드 박막의 전계방출특성에 미치는 영향을 고찰하고 이로부터 그 원인을 규명하고자 하였다. 다이아몬드 박막은 hot-filament 화학증착법을 이용하여 증착하였다. 후성장한 다잉아몬드 박막내의 흑연성분과 박막의 두께를 체계적으로 조절하여 후성장 박막의 구조적 특성과 그 두께의 영향을 확인할 수 있었다. 후성장층내의 흑연성분과 두께가 증가할수록 전계방출특성은 향상되다가 저하되었다. 한편, 다이아몬드 박막을 성장시킨 후 수소분위기 처리를 함에 따라 전계방출특성은 향상되었지만 수소처리시간이 5분 이상으로 증가함에 따라 그 특성은 저하되었다. 본 연구에서는 수소처리와 후성장시 나타나는 전계방출특성의 변화 원인을 규명하고자 한다.기판위에서 polymer-like Carbon 구조는 향상되는 경향을 보였다.0 mm인 백금 망을 마스크로 사용하여 실제 3차원 미세구조를 제작하여 보았다. 그림 1에서 제작된 구조물의 SEM 사진을 보여주었으며, 식각된 면의 조도가 매우 뛰어나며 모서리의 직각성도 우수함을 확인할 수 있다. 이와 같이 도출된 시험 조건을 기초로 하여 리소그래피 후에 전기 도금을 이용한 금속 몰드 제작 및 이온빔 리소그래피 장점을 최대한 살릴수 있는 미세구조 제작에 대한 연구를 계속 추진할 계획이다. 비정질 Si1-xCx 박막을 증착하여 특성을 분석한 결과 성장된 박막의 성장률은 Carbonfid의 증가에 따라 다른 성장특성을 보였고, Silcne(SiH4) 가스량의 감소와 함께 박막의 성장률이 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 줄어들어 성장률이 Silane가스량에 의해 지배됨을 볼 수 있다. UV-VIS spectrophotometer에 의한 비정질 SiC 박막의 투과도와 파장과의 관계에 있어 유리를 기판으로 사용했으므로 유리의투과도를 감안했으며, 유리에 대한 상대적인 비율 관계로 투과도를 나타냈었다. 또한 비저질 SiC 박막의 흡수계수는 Ellipsometry에 의해 측정된 Δ과 Ψ값을 이용하여 시뮬레이션한 결과로 비정질 SiC 박막의 두께를 이용하여 구하였다. 또한 Tauc Plot을 통해 박막의 optical band gap을 2.6~3.7eV로 조절할 수 있었다. 20$0^{\circ}C$이상으로 증가시켜도 광투과율은 큰 변화를 나타내지 않았다.부터

• Korean Journal of Soil Science and Fertilizer
• /
• v.35 no.6
• /
• pp.372-380
• /
• 2002

This study was conducted to investigate the changes of soil properties for potato and Chinese cabbage after application adding phosphorus and potassium fertilizers in the mounded highland soil from 1999 to 2001. Experimental plots were designed with control(NPK+Lime+Compost) and chemical improvement(Control+Application adding P and K). Mounded soil before field experiment of first year(1999) was low in organic matter, available phosphorus and exchangeable potassium, and the soil texture was loamy sand soil. After 3 years, the contents of soil organic matter increased a little, and available phosphorus and exchangeable potassium contents were remarkably increased. The crop growth in chemical improvement plot was better than control plot. Yield of chemical improvement plot in comparison with control plot was increased by 5~22% for potato and 6~25% for Chinese cabbage after 2~3 years.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.328-336
• /
• 1998

In metal-carbon system with no mutual solubility between matrix and alloying elements as solid or liquid phases, Cu-C-X nanocomposite metal powders were prepared by high energy ball milling for solid-lubricating bronze bearings. Elemental powder mixtures of Cu-lOwt.%C- 5wt. %Fe and Cu- lOwt. %C- 5wt. %Al were mechanically alloyed with an attritor in an argon atmosphere, and then microstructural evolution of the Cu-C-X nanocomposite metal powders was examined. It has been found that after 10 hours of MA, the approximately 10$\mu\textrm{m}$ sized Cu-C- X nanocomposite metal powders can be produced in both compositions. Morphological characteristics and microstructural evolution of the Cu-C-X powders have shown a similar MA procedure compared to those of metal-metal system. As a result of X - ray diffraction analysis, diffraction peaks of Cu and C were broaden and peak intensities were decreased as a function of MA time. Especially, the gradual disappearance of C peaks in the X- ray spectra is proved to be due to the lower atomic scattering factor of C. The calculated Cu crystallite sizes in Cu- C- X nanocomposite metal powders by Williamson- Hall equation were about lOnm size, on the other hand, the observed ones by TEM were in the range of 10 to 30nm.

• Journal of the Korean Chemical Society
• /
• v.36 no.4
• /
• pp.552-557
• /
• 1992

Chloramphenicol was studied by differential pulse polarography (DDP). A reduction peak which is dependent on pH of the solution appeared in the voltage range between zero and -1.50 volt vs. Ag/AgCl (sat. KCl) reference electrode. A plot of peak potentials (Ep) measured at room temperature (20$^{\circ}C$) vs. pH of the chloramphenicol solutions showed linear relationship changing slope (Ep/pH) at pH 8.9. The slope was -59.7 mV/pH in pH 2.7∼8.9 and -24.3 mV/pH in pH 8.9∼11.2, respectively. A log plot of peak currents (ip) vs. concentrations showed a linearity at the concentrations between 4.8 ${\times}$ 10$^{-7}$ M and 6.2 ${\times}$ 10$^{-5}$ M (0.16 ppm∼20 ppm) chloramphenicol in pH 8.0 ammonium buffer. Between the DPP method and the reference method measuring absorbance at 278 nm, the correlation coefficient was 0.996, which means an excellent linearity. The DPP method was able to detect degradation products of chloramphenicol in mild alkaline solution (pH = 8.0) more distinctly than the spectrophotometric method.