• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.87-94
• /
• 2014

It becomes critical to understand an energy coupling mechanism between flow perturbations and combustion heat release rate fluctuations for the understanding of high-frequency combustion instabilities occurring in high-performance combustion/propulsion systems. A significant amount of experimental researches have been carried out to understand flame dynamic characteristics by use of flame transfer functions with artificial flow disturbances. Among them, there exist substantial studies on flame response by the excitation of inlet flow. Recently, experimental studies simulating transversal modes excited in actual combustion systems are under way.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.175-184
• /
• 2006

Two methods of the nonlinear static pushover analysis have been presented for the performance-based seismic design and evaluation of MDOF continuous bridges. Guidelines for buildings presented in FEMA-273 applying the Displacement Coefficient Method (DCM) and in ATC applying the Capacity Spectrum Method(CSM) have been modified for MDOF bridges. Two methods are compared with the time- history analysis. The lateral load distribution pattern for seismic loads has been examined in the static pushover analysis. The force-based fiber frame finite element has been implemented in the modeling of reinforced concrete piers.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.11 no.4
• /
• pp.216-230
• /
• 1999

A Galerkin finite element model for the analysis of harbor oscillation has been developed based on the extended mild-slope equation. Infinite elements are used to accomodate the radiation condition at infinity and joint elements to treat the matching conditions at the harbor entrance which include the energy loss due to flow separation. The numerical tests for rectangular harbors with fully or partially open entrances show that the energy loss at the harbor entrance considerably reduces the the amplification ratios at the innermost parts of the harbors and that the amplification ratios decrease considerably with increasing incident wave heights and jet lengths at the harbor entrance. Application of the model to the Gamcheon harbor show that when the incident wave amplitude is small the amplification ratios rather increase when the entrance energy loss is included than when ignored because of the shift of the resonance periods. Even though the entrance energy loss was insignificant for the measured long-period incident waves, it would be of great importance if the incident waves were large as in the attack of tsunamis. The resonance period of the Helmholtz mode at the Gamcheon Harbor was calculated to be 31 minutes, which agrees well with the measured one between 27 and 33.3 minutes. The measured resonance periods between 9.4 and 12.1 minutes and 5.2 and 6.2 minutes were also calculated by the numerical model as 10.4 minutes and 6.6 or 5.6 minutes, indicating good performance of the model. On the other hand, it was shown that a variety of oscillation modes exists in the Gamcheon Harbor and lateral resonances of considerable amplification ratios also exist at the periods of 3.6 and 1.6 minutes as in the Young-II Bay.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.4
• /
• pp.19-33
• /
• 2008

Dynamic response measurements from natural excitation were carried out for 25- and 42-story buildings to evaluate their inherent properties, such as natural frequencies, mode shapes and damping ratios. Both are reinforced concrete buildings adopting a core wall, or with shear walls as the major lateral force resisting system, but frames are added in the plan or elevation. In particular, shear walls in a 25-story building are converted to frames from the 4th floor level downwards while maintaining a core wall throughout, resulting in a fairly complex structure. Due to this, along with similar stiffness characteristics in the principal directions, significantly coupled and closely spaced modes of motion are expected in this building, making identification rather difficult. By using various state-of-the-art system identification methods, the modal parameters are extracted, and the results are then compared. Three frequency-domain and four time-domain based operational modal identification methods are considered. Overall, all natural frequencies and damping ratios estimated from the different identification methods showed a greater consistency for both buildings, while mode shapes exhibited some degree of discrepancy, varying from method to method. On the other hand, in comparison with analysis results obtained using the initial finite element(FE) models, test results exhibited a significant difference of about doubled frequencies, at least for the three lower modes in both buildings. To improve the correlation between test and analysis, a few manual schemes of FE model updating based on plausible reasons have been applied, and acceptable results are obtained. The advantages and disadvantages of each identification method used are addressed, and some difficulties that might arise from the updating of FE models, including automatic procedures, for such large structures are carefully discussed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.174-182
• /
• 2014

To monitor the wind-induced responses of buildings, conventional real-time kinematic (RTK) methods based on two global positioning system (GPS) receivers (e.g., a reference and a rover) are widely applied. However, these methods can encounter problems such as difficulty in securing and maintaining a space for a reference station. With the recently developed virtual reference station (VRS)-RTK approach, the position of a structure can be measured using only a rover receiver. In this study, to evaluate the applicability of VRS-RTK methods in monitoring the lateral structural responses of frame structures, we performed free vibration tests on a one-story frame model (the first natural frequency of 1 Hz) and a three-story frame model (the first natural frequency of 0.85 Hz). To assess the reliability of the displacement and acceleration responses measured by the GPS, we performed a concurrent measurement using laser displacement sensors and an accelerometer. The accelerometer results were consistent with the GPS measurements in terms of the time history and frequency content. Furthermore, to derive an appropriate sampling rate for the continuous monitoring of buildings, the errors in the displacement responses were evaluated at different GPS sampling rates (5, 10, 20 Hz). The results indicate that as the sampling rate increased, the errors in the displacement responses decreased. In addition, in the three-story model, all modal components (first, second, and third modes) could be recorded at a sampling rate of 20 Hz.

• Journal of the Korea Concrete Institute
• /
• v.20 no.4
• /
• pp.503-511
• /
• 2008

This paper presents the results of an analytical and experimental study on the performance of reinforced concrete beams subjected to pure torsion. The main parameters of the experimental tests were amount of torsional reinforcement and the ratio of the transverse torsional reinforcement to the longitudinal torsional reinforcement. The test results indicated that the maximum amount of torsional reinforcement required in ACI 318-05 code underestimated almost twice as much as the observed maximum amount of torsional reinforcement. Comparisons between the tested and calculated torsional behaviors of the 102 beams showed that the torsional failure modes of ACI 318-05 code disagreed with the observed failure modes. In addition, the torsion provisions in ACI 318-05 code overestimate the torsional strength of the RC beams in which relatively large amount of torsional reinforcement were reinforced, while underestimate for the beams with small amount of torsional reinforcement. This discrepancy between the theoretical ultimate torsional strength as given by the ACI 318-05 code and the experimental one can be due to neglecting the tension stiffening effect and the contribution of the torsional strength by concrete.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.4
• /
• pp.777-790
• /
• 2001

Theoretical analyses have been tried to design high power and stable operating SLD at 1.55${\mu}{\textrm}{m}$ wavelength range which is the lowest absorption wavelength in optical fiber. The materials of active layer and SCH layer were chosen as conventional In1-xGaxAsyPl-y quaternary composition systems. From the transverse mode and the lateral mode analyses of waveguide, the optical power distributions and the optical confinement factor have been studied for single-mode high power operation. According to these analyses, it was calculated the composition and the thickness of SCH layer to obtain the maximum optical confinement factor. In order to obtain low values of the reflectivity, we used the window region and the lateral tilted angle between tile active region and window region. And the reflectivity of SLD was calculated with the gaussian beam approximation and mode analysis. From these researches, it was confirmed for several results to fabricate the efficient and stable SLD. In case of using $1.3\mum$, InGaAsP SCH layer, the layer thickness was obtained $0.08\mum$, to get the maximum optical confinement factor. Using $0.2\mum$, active layer thickness and $0.08\mum$, SCH layer thickness, the window region length is about $100\mum$ without An coating, $10\mum$ in 1% AR coating to obtain about 10-4 reflectivity. When the tilted angle is about $10~15^{\circ}$, the reflectivity is about 10-3. From these results, if the window region length and tilted angle were controlled appropriately in given device structure, it was confirmed that it is possible to fabricate the stable SLD without AR coating analytically.

• Journal of the Korean Society for Railway
• /
• v.15 no.6
• /
• pp.588-596
• /
• 2012

This paper presents a new semi-analytical annular Mindlin plate element with which out-of-plane natural vibration of thick disks can be analyzed simply, efficiently, and accurately through FEM by including effects of rotary inertia and transverse shear deformation. Using static deformation modes which are exact solutions of equilibrium equations of annular Mindlin plate, the element interpolation functions, stiffness and mass matrices corresponding to each number of nodal diameters are derived. The element is capable of representing out-of-plane rigid-body motions exactly and free from shear locking. Natural frequencies of uniform and multi-step disks with or without concentric ring support are analyzed by applying the presented element. Such results are compared with theoretical predictions of previous works or FEA results obtained by using two-dimensional shell element to investigate the convergence and accuracy of the presented element.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.4
• /
• pp.481-494
• /
• 2001

An enhanced degenerated shell finite element (FE), which has been developed for inelastic analysis of reinforced concrete structures is described in this paper. Generally, Reissner-Mindlin (RM) assumptions are adopted to develop the degenerated shell FE so that transverse shear deformation effects is considered. However, it is found that there are serious defects such as locking phenomena in RM degenerated shell FE since the stiffness matrix has been overestimated in some situations. As remedies of locking phenomena, reduced integration, incompatible mode and assumed strain method have been used. Especially, the assumed strain method has been successfully used in many FEs. But contrarily, there is a few investigation on the performance of the assumed strains in the inelastic analysis of concrete structures. Therefore, shell formulation is provided in this paper with emphasis on the terms related to the stiffness matrix based on assumed strain method and microscopic concrete material model. Finally, the performance of the present shell element is tested and demonstrated with several numerical examples. From the numerical tests, the present result shows a good agreement with experimental data or other numerical results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.4
• /
• pp.29-37
• /
• 1974

Theoretical analysis is carried out for the curtoff wavelength characteristics of rectangular waveguide containing a step-ridge. In order to obtain the cutoff wavelength of step-rigde waveguide, an transmission matriz is formulated by the method of equivalent transverse resonance. The characteristic equation, in which the wavelength is obtainable by the numerical method, is derived from the equation. An approximate determination of the dominant mode fields in step-ridge waveguides at all frequencies has been made. Using these fields, the characteristic impedance equation is derived from power considerations. Analyzing the results of the calculations, the following characteristics are noted. The values of λ /a of TE10 mode increase with decreasing gap lengths and with increasing step width S or S , or both. Experimental results of cutoff characteristics are in good agreement with the theoretical analusis. It is shown that a waveguide within which a step-ridge is placed has a lower cutoff frequency and impedance than empty guide without it. Therefore, the role of a step-ridge guide is to broadening the bandwidth 2 to 3 times more than that of an empty guide of the same demension.