• Restorative Dentistry and Endodontics
• /
• v.35 no.4
• /
• pp.257-266
• /
• 2010

The purpose of this study was to determine the effect of post types and sizes on fracture resistance in immature tooth model with various restorative techniques. Bovine incisors were sectioned 8 mm above and 12 mm below the cementoenamel junction to simulate immature tooth model. To compare various post-and-core restorations, canals were restored with gutta-percha and resin core, or reinforced dentin wall with dual-cured resin composite, followed by placement of D.T. LIGHT-POST, ParaPost XT, and various sizes of EverStick Post individually. All of specimens were stored in the distilled water for 72 hours and underwent 6,000 thermal cycles. After simulation of periodontal ligament structure with polyether impression material, compressive load was applied at 45 degrees to the long axis of the specimen until fracture was occurred. Experimental groups reinforced with post and composite resin were shown significantly higher fracture strength than gutta-percha group without post placement (p < 0.05). Most specimens fractured limited to cervical third of roots. Post types did not influence on fracture resistance and fracture level significantly when cement space was filled with dual-cured resin composite. In addition, no statistically significant differences were seen between customized and standardized glass fiber posts, which cement spaces were filled with resin cement or composite resin individually. Therefore, root reinforcement procedures as above in immature teeth improved fracture resistance regardless of post types and sizes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.628-637
• /
• 2017

The automobile industry has developed Advanced Driver Assistance Systems (ADASs) to prevent traffic accidents and reduce the burden for drivers. One example is the Lane Keeping Assistance System (LKAS), which was developed for automotive vehicle systems for safety and better driving. The main system of the LKAS supports the driver while maintaining the vehicle within a lane. LKAS uses a radar sensor and camera sensor to collect information about the vehicle's position in the lane and send commands to the actuator to influence the lateral movement of the vehicle if necessary. Recently, vehicles equipped with LKAS have become commercially available. Test procedures for international LKAS evaluation are being discussed and developed by international committees, such as the International Organization for Standardization and United Nations Economic Commission for Europe. In Korea, an evaluation of LKASs for car safety is being planned by the Korean New Car Assessment Program. Therefore, test procedures should be developed for LKASs that are suitable for the domestic road environment while accommodating international standards. We developed a test scenario for LKASs and propose a formula for obtaining the target relative distance. To validate the methods, a series of experiments were conducted using commercially available vehicles equipped with LKAS.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.4
• /
• pp.361-374
• /
• 2007

This study presents long-term shoreline changes of barrier islands in Nakdong Estuary using aerial photographs. Digital photogrammetry is used for constructing mosaic aerial photographs, which yield six sets of shoreline data ranging from 1975 to 2001. Three kinds of rate of shoreline changes such as EPR (End Point Rate), JKR(Jackknife Rate) and LRR (Linear Regression Rate) are computed by a GIS-based Digital Shoreline Analysis Systems. There have been remarkable changes both in Sinja Island and Doyodeung. Western part of Sinja Island advanced seaward, whereas eastern part retreated landward, giving appearance that the island rotated counterclockwise. Rate of shoreline changes at both ends reach 20 m/yr. Doyodeung occurred newly in front of Baekhapdeung in 1993, resulting in shoreline advance in a rate of 40 m/yr. Rate of shoreline changes differ both within and between barrier islands and have a tendency to increase eastward. To understand this spatial variability of rate of shoreline changes, it is suggested to make a detailed investigation into the impact of coastal development on hydrodynamic and sedimentary processes.

• Economic and Environmental Geology
• /
• v.50 no.1
• /
• pp.45-59
• /
• 2017

In this research, we have extracted historical records regarding the geotechnology from the Goryeosa and the Annals of the Joseon Dynasty which are rated as ancient books that have objective views in the Goryeo Dynasty and the Joseon Dynasty in order to understand the national awareness and the social situation of the past events. We used the Korean history database system of National Institute of Korean History (NIKH) and collected related records by searching specific keywords such as volcano, mining, hot spring, and meteorite. According to the historical records, geological events such as the volcano and meteorite were regarded as important issues which were enough to be recorded in annals and surveyed by the dispatched government officials to the fields of events. In case of the hot springs, government officials conducted explorations of hot springs at king's orders and developed the potential areas of hot springs. Among the historical records on mining, the contents of geotechnology including the contents about discovered minerals and its locations can be easily found from those ancient books. Especially, it is possible to understand the history of geotechnology such as an establishment of modern organizations and a capitalistic flow for development through the history of the mining in the late Joseon Dynasty.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.171-178
• /
• 2018

The ocean is a harsh environment and Korea Coast Guard officers often face the threat of death or going missing in the line of duty. In order to promptly identify unknown bodies during mishaps, Korea Coast Guard Research Center has established an identification system using the DNA of its officers. This collected DNA can also be entombed in National Cemeteries when the remains are not recovered. The storage, disposal and quality control of the materials are overseen by the Governing Committee according to the Enforcement Rules for the Human Biological Materials Storage Project for the Identification of Officers Killed or Gone Missing in Action. Approximately 700 bodies are found per year along the Korean coast. An alternative method should be put in place for when identification through fingerprints and teeth are not applicable due to severe decomposition or partial recovery. We believe it would greatly contribute to helping identify the unknown bodies if the storage project could expand its data to include marine industry workers, relevant researchers and those involved in marine leisure activities.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.241-247
• /
• 2017

Railway bridges with continuously welded rail have a limitation of span length due to track-bridge interaction. In order to overcome this, a sliding slab track system has been developed that comprises with a low-frictional sliding layer between the bridge deck and the track slab to isolate the longitudinal behavior between the bridge and the track. In this study, a real scale track system is prepared to experimentally evaluate the longitudinal frictional behavior. Applied loading rates were 0.2, 1.0, 5.0 and 10mm/min; vertical mass on the track are track slab only, 5,000 and 10,000kg added mass, respectively. Test results showed that the resulting frictional coefficients varied from 0.22 to 0.33. In addition, 10,000 cycle loadings were applied to simulate repetitive sliding to represent 30 years of service life. The frictional coefficient increase was measured and found to be 7% of that of the initial loading stage, which means that the sliding layer is adequate to provide low-frictional behavior for the sliding slab track system. Effects of changes of the frictional coefficient of the sliding layer were analyzed by rail-structure interaction analysis.

• The Journal of the Korea Contents Association
• /
• v.18 no.6
• /
• pp.169-179
• /
• 2018

The Korean society has become increasingly concerned about the safety consciousness because of the Sewol Ferry disaster in April 2014. This shows the absence of social system and safety consciousness of Korean society that has been rapidly growing through fast industrialization. The purpose of this paper is to suggest guidelines for the production of a safety animation by approaching the discourse of public value. For this research process, first, literature review will be conducted by focusing on the safety culture, causes of safety accidents, safety education and educational effect using animation. Second, I will analyze 11 safety animation films by focusing on (1) construction of accident environment(narrative, character and background design) (2) exploration of dangerous elements and accident happening(accident type and dangerous elements, method of direction for accident happening, damage degree) (3) the guideline for safety behaviour. Third, guidelines for the production of safety animation will be suggested by analyzing the results of literature reviews and case studies in a comprehensive way. It is expected that this paper will be used as a basic data for academic research and animation production related to the safety accident.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.5
• /
• pp.269-274
• /
• 2013

To proportionally control the electronic valve position of the actuator, we designed and fabricated PCU, CPT, and rotary absolute optical encoder for the detection of absolute angular position in the actuator. We also designed and constructed the test system by using DAQ hardware and Labview. We designed PCU to convert 1-5 V, 0-5 V, 0-10 V, 2-10 V voltage signals and 4-20 mA current signals to the voltage signals in the common 0.5-2.5 V range. We designed CPT to output 4-20 mA current signals corresponding to the valve positions based on the PWM signal input from the MCU. We also designed 20 bit optical encoder by using infrared LED and infrared transistor and made the serial communication with the main board possible. When we tested PCU and CPT with DAQ hardware and Labview software, they operated correctly with the small errors within ${\pm}0.003$ V and ${\pm}0.01$ mA, respectively, showing that our actuator has the excellent performance to employ as the industrial proportional-valve-actuator. The resolution of the encoder was $11.25^{\circ}$ and the maximum revolution to detect was 32,768.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.8
• /
• pp.1960-1971
• /
• 1998

The researches and developments to provide multimedia communication services such as Video on Demand(VoDJ), real time video phonc and multipoint vidco conferencing on broadband ISDN environmcnts have been proceeded with activity. Specifications for Vol) services which is worked by Digital Audio-Visual Council(DAVIC) to support detail technologies including total service system that is consist of VoD server. delive[\! networl, and Set-Top Box(STB) had been already finished and ITU-T SG16 also recommended the standards of H.300 series terminal aspects for conversational multimedia services, But the architectures of multimedia tenninals recommended and specified by these organizations do not have an efficient st11lcture to provide all of retrieval, distrihution and conversational service due to a different point of view about multimedia terminals and services. In this paper, we analyzed the recornmendatio!E and the specifications of intemational public and private organizations like lTU-T, DAVIC and ATM forum. As a result of these analysis. we propose an efficient terminal architecture, and then we have designed, lmplemented the multimedia communication terminal for offering VoI) and real- time conversation ,,, functional module test according to the individual commumication service session and confirined the validiry or terminal implemented to be used on broadband ISDK environments.

• Proceedings of the Korean Information Science Society Conference
• /
• 2007.10b
• /
• pp.247-252
• /
• 2007

오늘날 컴퓨팅 환경은 점차 복잡해지고 있으며, 복잡한 환경을 관리하는 이 점차 중요해 지고 있다. 이러한 관리를 위해 어플리케이션의 내부 구조를 드러내지 않은 상태에서 환경에 적응하는 자가치유에 관한 연구가 중요한 이슈가 되고 있다. 우리의 이전 연구에서는 자가 적응 모듈의 성능 향상을 위해 스위치를 사용하여 컴포넌트의 동작 유무를 결정하였다. 그러나 바이러스와 같은 외부 상황에 의해 자가 적응 모듈이 정상적으로 동작하지 않을 수 있으며 다수의 파일을 전송할 때 스위치가 꺼진 컴포넌트들은 메모리와 같은 리소스를 낭비한다. 본 연구에서는 이전 연구인 성능 개선 자가 적응 모듈에서 발생할 수 있는 문제점을 해결하기 위한 방법을 제안한다. 1) 컴포넌트의 동작 여부를 결정하는 스위치를 확인하여 비정상 상태인 컴포넌트를 찾아 치유를 하고, 2) 현재 단계에서 사용하지 않는 컴포넌트를 다른 작업에서 재사용한다. 이러한 제안 방법론을 통해 파일 전송이 않은 상황에서도 전체 컴포넌트의 수를 줄일 수 있으며 자가 적응 제어 모듈을 안정적으로 작동할 수 있도록 한다. 본 논문에서는 명가를 위하여 비디오 회의 시스템 내의 파일 전송 모듈에 제안 방법론을 적용하여 이전 연구의 모듈과 제안 방법론을 적용한 모듈이 미리 정한 상황들에서 정상적으로 적응할 수 있는지를 비교한다. 또한 파일 전송이 많은 상황에서 제안 방법론을 적용하였을 때 이전 연구 방법론과의 컴포넌트 수를 비교한다. 이를 통해 이전 연구의 자가 적응 모듈의 비정상 상태를 찾아낼 수 있었고, 둘 이상의 파일 전송이 이루어 질 때 컴포넌트의 재사용을 통해 리소스의 사용을 줄일 수 있었다.위해 잡음과 그림자 영역을 제거한다. 잡음과 그림자 영역을 제거하면 구멍이 발생하거나 실루엣이 손상되는 문제가 발생한다. 손상된 정보는 근접한 픽셀이 유사하지 않을 때 낮은 비용을 할당하는 에너지 함수의 스무드(smooth) 항에 의해 에지 정보를 기반으로 채워진다. 결론적으로 제안된 방법은 스무드 항과 대략적으로 설정된 데이터 항으로 구성된 에너지 함수를 그래프 컷으로 전역적으로 최소화함으로써 더욱 정확하게 목적이 되는 영역을 추출할 수 있다.능적으로 우수한 기호성, 즉석에서 먹을 수 있는 간편성, 장기저장에 의한 식품 산패, 오염 및 변패 미생물의 생육 등이 발생하지 않는 우수한 생선가공, 저장방법, 저가 생선류의 부가가치 상승 등 여러 유익한 결과를 얻을 수 있는 효과적인 가공방법을 증명하였다.의 평균섭취량에도 미치지 못하는 매우 저조한 영양상태를 보여 경제력, 육체적 활동 및 건강상태 등이 매우 열악한 이들 집단에 대한 질 좋은 영양서비스의 제공이 국가적 차원에서 시급히 재고되어야 할 것이다. 연구대상자 특히 배달급식 대상자의 경우 모집의 어려움으로 인해 적은 수의 연구대상자의 결과를 보고한 것은 본 연구의 제한점이라 할 수 있다 따라서 본 연구결과를 바탕으로 좀 더 많은 대상자를 대상으로 한 조사 연구가 계속 이루어져 가정배달급식 프로그램의 개선을 위한 유용한 자료로 축적되어야 할 것이다.상범주로 회복함을 알수 있었고 실험결과 항암제 투여후 3 일째 피판 형성한 군에서 피판치유가 늦어진 것으로 관찰되어 인체에서 항암 투여후 수술시기는 인체면역계가 회복하는 시기를 3주이상 경과후 적어도 4주째 수술시기를 정하는 것이 유리하리라 생각되