• Journal of dental hygiene science
• /
• v.6 no.4
• /
• pp.231-235
• /
• 2006

This study evaluated the properties of polyvinylsiloxane impression materials: Strain-in-compression, Elastic recovery, Consistency, and Wettability. Four polyvinylsiloxane impression materials(Examixfine, GC, Japan; Aquasilultra, Dentsply, USA; Extrude, Kerr, USA; Perfect-F, Handae, Korea) were used in this study. The measured data were analyzed with SPSSWIN 12.0 program. The results were as follows : 1. The strain-in-compression values showed that Extrude had the lowest value, 4.86% and Examixfine had the highest value, 6.78%. Significant difference between Examixfine and Perfect-F was not found but the other groups had significant differences(p = 0.000). 2. In the elastic recovery test, Extrude had the highest, 99.83% and Perfect-F had the lowest, 96.54%. There is no significant difference between Examixfine and Aquasilultra. The other impression material groups showed significant differences(p = 0.000). 3. The measurement of consistency results that the diameter of Examixfine was the largest, 45.12mm and one of Perfect-F was the smallest, 40.28 mm. No differences were shown between Examixfine and Aquasilultra and between Extrude and Perfect-F(p = 0.001). 4. Aquasilultra had a better hydrophilicity($47.85^{\circ}$) than other materials. Perfect-F had a larger contact angle($94.89^{\circ}$) and was hydrophobic. There were significant differences between groups(p = 0.000). 5. As for correlation among the test types, contact angle correlated with strain-in-compression, elstic recovery and consistency. The strain-in-compression had correlation to contact angle and elastic recovery. The elastic recovery correlated with contact angle and strain-in-compression. And the consistency had correlation to contact angle.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.442-446
• /
• 2009

Recovery behaviors of unfilled NR, BR, and SBR vulcanizates after aging with a circular deformation were compared to prevent the influence of reinforcing agent. Samples were aged at room temperature, 50, 70, and $90^{\circ}C$ for 10 days. Recovery increased by increasing the measurement time. Instantaneous recoveries less than 1.0 sec were obtained using the recovery variations with the measurement time. For aging at room temperature, difference in the recoveries of the rubber samples was not significant because the aging time was too short. However, for accelerated thermal aging at 50, 70, and $90^{\circ}C$, difference in the recoveries of the rubber samples was significant. Degree of recovery of BR specimen was higher than those of the others, while that of SBR was lowest. However, for accelerated thermal aging at $90^{\circ}C$, recovery of the NR sample was higher than that of the BR one. The initial recovery decreased by increasing the aging temperature and the decrement of SBR was larger than the others. The experimental results were explained with the resilience properties of rubbers and the crosslink density changes by thermal aging.

• Elastomers and Composites
• /
• v.48 no.3
• /
• pp.181-189
• /
• 2013

Unfilled, carbon black-filled, and silica-filled natural rubber (NR) composites were aged with a circular deformation at $60-90^{\circ}C$ and the recovery behaviors were investigated. The samples were aged under the altering aging medium systems of air and distilled water every day for 10 days. The order of the recoveries according to the filler systems was unfilled > silica > carbon black. The recoveries of the samples aged in the air to water altering system were greater than those of the samples aged in the water to air altering system. The initial aging medium dominantly influenced the deformation level.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.2
• /
• pp.15-21
• /
• 2013

The analysis of long-term performance of pavement sections under wheel loads is normally conducted in two separated steps. First the resilient behavior of the pavement is calculated assuming the pavement is a layered or discrete elastic medium, and then the permanent deformation is evaluated based on empirical permanent displacement equations. Material properties required in both steps can be obtained from cyclic triaxial tests, in other words, resilient and permanent deformation tests. While this analytical approach is simple and convenient, it does not consider the modulus degradation caused by cyclic loads, and some types of reinforcements such as geosynthetic cannot be modeled in this type of analysis. A model for degraded secant modulus is proposed and suggested to be used for the analysis of permanent behavior of unpaved roadway sections. The parameter for suggested model can be obtained from cyclic triaxial tests, regular practice in pavement engineering. Examples to estimate the model parameters are presented based on both laboratory permanent deformation test and large-scale plate load test.

• Composites Research
• /
• v.22 no.3
• /
• pp.29-34
• /
• 2009

In this paper, finite element analyses were used to estimate the strain distribution at the fracture site of a tibia bone. A stainless steel bone plate and various composite bone plates were considered to find out the best conditions for callus generation while bone fracture was cured for 16 weeks. Through this research, the appropriate load condition which makes the strains between the appropriate range($2{\sim}10%$) was sought. From this analysis, it was found that lower level of external load is needed for the appropriate strain for the case of composite bone plate application and it was also found that the composite bone plate had potential advantages for effective bone fracture healing relieved stress shielding effect.

• International Journal of Highway Engineering
• /
• v.7 no.2 s.24
• /
• pp.69-76
• /
• 2005

While the repeated traffic loading accumulates the damage of asphalt pavement, the damage has being healed during rest periods. And then, this healing enhances the fatigue life of asphalt pavement. A method was developed to determine the healing rate of asphalt mixture in terms of recovered dissipated creep strain energy (DCSE) per unit time, and the healing properties of four different asphalt mixtures were evaluated. The test procedure consists of repeated loading test and periodical resilient modulus tests. A normalized healing rate in terms of $DCSE/DCSE_{applied}$ was defined to evaluate the healing properties independently of the amount of damage incurred in the mixture. From the test results, it was concluded that the healing rates of asphalt mixtures were increased exponentially as the temperature was increased and more affected by the structural characteristics of mixture such as asphalt content than the binder characteristics such as the polymer modification.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.2
• /
• pp.195-204
• /
• 2004

A series of constant creep and repeated creep tests are performed to investigate the behavior of visco-elasto-plastic materials of chemical grouted sands. In the result of constant creep test, the material exhibits three types of shear strain : elastic, plastic, viscoelastic. The elastic, plastic and viscoelastic strains are linear, i.e., the strains are proportional to the stresses for loading. Good agreement is found between the predicted viscoelastic and test results by the power law and the generalized model. In the repeated creep test, the instantaneous recoverable strain is time-independent and the magnitude of accumulated plastic strain increases with number of cycles. Also it is seen that the accumulated plastic strains are approximately proportional to stress. There are no significant differences between test results predicted values for first cycle, and the differences increase relatively insignificantly with number of cycles.

• Elastomers and Composites
• /
• v.47 no.2
• /
• pp.156-161
• /
• 2012

Difference in recovery behaviors from the circular deformation of natural rubber (NR) composites aged in air and distilled water, respectively were investigated. Recoveries of the samples aged in air were larger than those of the samples aged in distilled water. Recovery rates of the samples reinforced with filler were faster than those of the unreinforced ones. Recovery rates of the carbon black-filled samples were faster than those of the silica-filled ones. Difference in the recovery behaviors according to the aging media can be explained by the crosslinking density changes and the annealing effect.

• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.258-265
• /
• 2005

To study the compressive stress, recovery force and permanent strain of foams for footwear midsole, polyurethane(PU), phylon(PH) and injection phylon(IP) foams were repetitively compressed with constant compressive stress. Maximum compressive stress of PU did not decrease with repetitive compression on the constant compressive stress, but that of IP largely decreased. Engineering strain of foams were formed by repetitively compressing the three types of foam. The engineering strain of PU was smaller than that of IP and PH. Compressive stress and recovery force of IP and PH at certain strain were decreased with repetitive compression, but that of PU was not noticeably changed.

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.433-436
• /
• 2002

형상기억재료는 형상기억효과, 회복변형효과, 형상고청효과, 진동제어효과 등의 특성으로 인하여 중요한 지능재료(smart materials)의 하나로 기대되고 있다. 형상기억 재료로는 합금, 세라믹, 고분자, 겔 등을 들 수 있지만 Ti-Ni 합금(Nitinol)이 가장 많이 이용되고 있다. 그러나 형상기억고분자는 형상기억합금에 비하여 가볍고 형상회복률이 높으며 가공이 쉽고 투명할 뿐만 아니라 염색이 가능하기 때문에 물성과 경제적인 면에서 유리하다. (중략)