• Journal of Navigation and Port Research
• /
• v.36 no.3
• /
• pp.157-162
• /
• 2012

A planing craft is designed specifically to achieve comparatively high speed on the surface of the water. The frictional resistance of planing craft can be reduced further by injecting air to the craft's bottom. In this paper, the resistance characteristics of high speed planing crafts with & without air injection at the bottom were compared by sea model-test method. As a result, we conformed that planing craft with air injection has much greater the effect of resistance reduction.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.759-764
• /
• 2008

The planing craft is designed specifically to achieve comparatively high speed on the surface of the water. Most of planing crafts have installed the spray strip in decreasing of wave impaction and improving motion performance of rolling and pitching et al. It is known to reduce the spray and frictional resistance by the effect of lift and improvement of wave profile in high speed. In this paper, the high speed planing crafts with & without spray strip in bottom were performed to compare the resistance performance by model-test. In conclusion, the high speed planing crafts with spray strip in bottom was proved to effect of the resistance decrement of $3.0{\sim}5.0%$.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.64-68
• /
• 1994

이 글에서는 활주형선의 단면형상 및 장-폭비와 저항특성과의 관계를 실험적으로 살펴보았다. 본 연구는 5단계로 구성된 연구 계획중 졔 1단계 연구로써 수행되었으며 본 연구를 통하여 단면형상 및 장-폭비의 변화에 따른 저항특성, 종방향 경상(trim), 그리고 침하량(sinkage)의 변화에 대한 초기 결론을 내릴 수 있다. 이러한 초기 결과를 가지고 활주형선의 일반적인 특성에 대한 어떤 분명한 결론을 내리기에는 부족하다고 하겠으나 앞으로 남은 연구를 효율적, 성공적으로 이끌어 가기 위한 초석이 된다고 할 수 있겠다.

• Journal of Navigation and Port Research
• /
• v.32 no.8
• /
• pp.583-588
• /
• 2008

The planing craft is designed specifically to achieve comparatively high speed on the surface of the water. In general, the stepped hull craft has effect improvement in speed and fuel-efficiency because of the reduction of total resistance by a small wetted surface area without corresponding stepped hull craft. In this paper, the high speed stepped hull crafts with respect to the number of bottom steps were performed to compare the effect of resistance performance using at-sea model-test method. In conclusion, the stepped hull craft with twin-step was proved to be effective to reduce the total resistance.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.37-39
• /
• 2007

고속 활주형선의 선형시험 ${\cdot}$ 검증을 위하여 설 해상모형시험기법을 정립하였으며, 본 시험법을 이용하여 선미 보조동체 장착 유무에 따른 고속 Stepped Hull 선형의 횡동요 및 저항특성을 비교, 분석하였다.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.125-125
• /
• 2017

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.128-128
• /
• 2017

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.3
• /
• pp.202-210
• /
• 2013

As incomes increase, interest in ocean leisure picks up. As a result, a lot of research and developments on hull form design and production of planing boats, mostly used for ocean leisure, are needed. Analysis in researches on resistance of planing boats shows that resistance characteristic of planing boats is different from resistance characteristic of general boats because the former is fast, and its wetted surface is very small. Using Savitsky formula widely used in the calculation of effective horse power in shipbuildingyards, and propulsion system and engine manufacturers, this study calculated total resistance of a research planing boat. Then it analyzed the flow characteristics of the planing boat through theoretical analysis and wind tunnel experiment, and computed air resistance and lift force by changes of speed and trim angle. It also compared and analyzed result of theoretical analysis and experiment of the ratio of air resistance to total resistance under variations of velocity and trim angle. When the study is used to estimate more accurate effective horse power, it is expected to remedy abuses of unnecessarily installing high-powered engine. As nature disasters due to abnormal changes of weather increase, interest in greenhouse gas grows. International Maritime Organization (IMO) legislated Energy Efficiency Design Index (EEDI) and Energy Efficiency Operational Indicator (EEOI) to reduce ship greenhouse gas emissions. But this index will be applied to over 400 tons ships, small ships, emitting more greenhouse gases than larege ships per unit power, will dodge the regulations. Thus, this study indicated a problem by calculating greenhouse gas emissions of an ocean leisure planning boat (a small ship), and suggested the need for EEDI of small ships.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2001.05a
• /
• pp.79-80
• /
• 2001

본 연구는 고속 활주형선의 어선 적용을 위해 경제성 및 운항ㆍ조업성능 등을 고려하여 .자료조사를 수행하고 기본 치수를 선정하였으며, 본 연구의 목적은 선정된 우수선형의 실선적용을 위해 실해역에서 발생할 수 있는 여러 조건들을 가정하여 발생 가능한 문제들을 예측하고 이를 방지 또는 개선하는 데 있다. (중략)

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.1
• /
• pp.17-22
• /
• 2004

This study was carried out at the CWC of Chosun university for the purpose of resistance performance improvement of planing hull, and the results of the tests were confirmed cooperatively with WJFEL. G/T 100 ton class planing hull form was selected, and the improvement of hull form including appendages were performed by using some model test techniques. The model test scope comprises resistance relative tests including wave profile observation, trim and sinkage measurement and flow visualization tests at full load and trial conditions for one bare hull and for two appended hulls. The final wedge and spray strip combined with improved hull form showed about 1.0 knot speed improvement at both of full and trial conditions, and outstanding improvement for fore wave phenomena.