• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.739-744
• /
• 1995

연소도 33 MWD/kgU에 해당하는 simulate $UO_2$ 소결체를 제조하여, 산화 (대기중 40$0^{\circ}C$), 고온산화 (대기중 110$0^{\circ}C$), 환원 (수소분위기 $600^{\circ}C$)을 차례로 실시하였다. 이 분말을 다시 산화/환원 처리를 반복하면서 분말의 크기, 비표면적, morphology를 조사하였다. 분말의 비표면적은 고온산화에 의해서 크게 감소했다가 산화/환원 cycle이 반복될수록 증가하는 경향을 보인다. attrition 분쇄에 의해서 분말의 비표면적은 매우 커지며, 그 증가폭은 산화/환원 cycle이 많아질수록 커진다. 고온산화 후 산화/환원 cycle을 2회 반복했을 때 소결밀도가 가장 높았다.

• Journal of the Korean Ceramic Society
• /
• v.38 no.4
• /
• pp.380-387
• /
• 2001

140$0^{\circ}C$ 환원 분위기(질소-수소) 조건에서 열처리하여 반도성 SrTiO$_3$하소분말을 제조하였다. 하소분말을 이용하여 135$0^{\circ}C$에서 2시간동안 상압 소결하여 소결체를 제조하였으며, 이때 소결 분위기에 따른 소결체 입계의 전기적 특성을 고찰하였다. 이들 소결체는 전형적인 바리스터 특성을 나타내었으며, 특히 소결 분위기를 질소-수소로부터 공기로 변화시킴에 따라서 소결체의 문턱 전압, 입계 비저항 그리고 입계 전위 장벽은 430V/cm, 10MΩ.cm 그리고 2.0$\times$$10^{-3}$eV로부터 1000V/cm 이상, 240 MΩ.m 그리고 1.1eV로 변하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.77-82
• /
• 2010

Effects of evaporation processes and a reduction annealing on thermoelectric properties of the Sb-Te thin films prepared by thermal evaporation have been investigated. The thin film evaporated by using the powders formed by crushing a $Sb_2Te_3$ ingot as an evaporation source exhibited a power factor of $2.71{\times}10^{-4}W/m-K^2$. The thin film processed by evaporation of the mixed powders of Sb and Te as an evaporation source showed a power factor of $0.12{\times}10^{-4}W/m-K^2$. The thin film fabricated by coevaporation of Sb and Te dual evaporation sources possessed a power factor of $0.73{\times}10^{-4}W/m-K^2$. With a reduction annealing at $300^{\circ}C$ for 2 hrs, the power factors of the films evaporated by using the $Sb_2Te_3$ ingot-crushed powders and coevaporated with Sb and Te dual evaporation sources were remarkably improved to $24.1{\times}10^{-4}W/m-K^2$ and $40.2{\times}10^{-4}W/m-K^2$, respectively.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.188-198
• /
• 2007

Platinum nanoparticles loading on carbon nanotube was carried out by impregnation of hexachloro platinate(IV) from hydrogen hexachloro platinate(IV) hydrate dissolved solution without using reduction agents, and heating the hexachloro platinate(IV) impregnated carbon nanotube up to $400^{\circ}C$. The amounts of impregnated hexachloro platinate(IV) on to carbon nanotube were measured with UV-visible spectrophotometer. The TG, XRD, and TEM analysis were performed to confirm the platinum particles loading and distribution on carbon nanotube. The average platinum particles size on carbon nanotube was under 2 nm by heating the hexachloro platinate(IV) up to $400^{\circ}C$ in spite of non-using reduction agents, while the average size increased due to the agglomeration of some particles by heating them up to $800^{\circ}C$. Therefore, uniformly distributed platinum nanoparticles loading on carbon nanotube can be obtained from simple impregnation of hexachloro platinate(IV) from solution and heating it up to $400^{\circ}C$.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.57-62
• /
• 2014

Using flexible bismaleimide-triazine co-polymer as a substrate, inkjet-printed Cu films were also investigated for low-cost and process feasibility of flexible electronics. After annealing at $200^{\circ}C$ for 1 h under various reducing ambient, surface color was changed to red and electrical resistivity was decreased to the level of conductor under formic acid ambient. However, its resistivity was much higher than conventional copper films due to surface crack. In order to reduce the residual film stress after annealing, additional isothermal treatment was inserted before anneal hiring the stress relaxation applied in processes of amorphous materials. As a result, no surface crack was observed and electrical resistivity of $3.4{\mu}{\Omega}cm$ was measured after annealing at $230^{\circ}C$ with stress relaxation while electrical resistivity of $7.4{\mu}{\Omega}cm$ was observed after normal annealing without relaxation. The effect of stress relaxation was also confirmed by observing surface crack after decreasing the relaxation time to 0 min.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.318-323
• /
• 2009

The lightweight aggregates made of bottom ash (70 wt%) and dredged soil (30 wt%) were prepared to investigate the property differences at various sintering atmospheres. The green aggregates were sintered at $1150^{\circ}C$ and $1200^{\circ}C$ with oxidized, neutralized and reduced atmospheres. The aggregates sintered with oxidized atmosphere showed a clear border between shell and black core area. However, the aggregates sintered with a reduced atmosphere showed only black core area in the entire cross-section of the aggregates. The black core area of the aggregates sintered with a neutralized atmosphere increased with increasing $N_2$ gas flow rates. It was determined that the sintering atmosphere was similar to that of rotary kiln when the CO gas flow was 100 cc/min to make a reduced atmosphere in tube furnace. The water absorption rates of both aggregates from tube furnace with reduced atmosphere and rotary kiln were very similar to each other.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.96-104
• /
• 2009

In order to lower a reaction temperature with high conversions for simultaneous catalytic reduction of NO and $N_2O$ over Pd-Rh supported mixed metal oxide honeycomb catalysts, $H_2$ or CO was utilized as a reductant. When using the reductants, the effects of reaction conditions were examined in NO and $N_2O$ conversions, where reaction temperatures, concentrations of the reductants and oxygen and the concentration ratio of $N_2O$ to NO were varied. In using $H_2$ reductant, larger than 50% of NO and $N_2O$ conversions was observed at the temperatures below $200^{\circ}C$ in absence of $O_2$. In using CO reductant, NO and $N_2O$ conversions increased from the temperatures higher than $200^{\circ}C$ and $300^{\circ}C$, respectively. However, in use of both reductants, NO and $N_2O$ conversions decreased with increasing oxygen concentration. As a result, $H_2$ reductant could reduce simultaneously NO and $N_2O$ at relatively lower reaction temperature than CO. Also, NO and $N_2O$ conversions were less influenced by using $H_2$ reductant than CO one. Concentration ratio between NO and $N_2O$ did not affect their conversions regardless the type of reductants. Pretreatment of the catalyst in $H_2$ was more effective in simultaneous reduction of NO and $N_2O$ at low reaction temperature than that in $O_2$.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.1
• /
• pp.53-64
• /
• 2007

The dynamic release behavior of Cs from high burn-up spent PWR fuel was experimentally performed under the conditions of a thermal treatment process such as voloxidation and sintering conditions. In voloxidation process, influence of the oxidation and reduction atmosphere on the Cs release characteristic using fragment type of spent fuel heated up to $1,500^{\circ}C$ was compared. In sintering process, temperature history effect on Cs release behavior was evaluated using green pellet under 4% $H_2/Ar$ environment. Temperature range for complete Cs release from spent fuel fragment under voloxidation condition was about $800^{\circ}C{\sim}1,200^{\circ}C$, but that of green pellet under the reduction atmosphere was $1,100^{\circ}C{\sim}1,400^{\circ}C$. Key parameters on Cs release behavior from spent fuel was powder formation as well as the diffusion rate of Cs compound to grain boundary and fuel surface.

• Resources Recycling
• /
• v.28 no.3
• /
• pp.45-52
• /
• 2019

$TiO_2$ as a raw material for producing titanium can be produced by carbon reduction of natural ilmenite ores over 1823 K and acid leaching of the obtained titanium-rich slag. However, the conventional process can cause very high energy consumption and a large amount of leaching residues. In the present study, we proposed the sulfurization of $FeTiO_3$ with $Na_2SO_4$ at temperatures below 1573 K, which can separate Fe in $FeTiO_3$ as the FeS based sulfide phase and Ti as the $TiO_2-Na_2O$ based oxide phase. This study is a fundamental study for sulfurization of $FeTiO_3$ to investigate the influence of reducing atmosphere, reaction temperature and the sulfur/Fe ratio on the separability and distribution behaviors of of Fe, Ti, and Na between the oxide phase and the sulfurized phase. At 1573 K and carbon saturation condition, the Fe can be separated from $FeTiO_3$ as Fe-C-S metal and a part of FeS, and the concentration of Fe in oxide decreased to 4 mass% after sulfurization.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.726-729
• /
• 2000

The entitled report revealed that ZnO phosphor samples treated at different temperatures under a given reduction atmosphere show the radiation brightness increase with increase of temperature up to about 900$^{\circ}C$ but become decreasing beyond the temperature. The brightness deterioration with curing temperature at higher temperatures was explained by the decrease of excess zinc ions resulted from their evaporation. The comments will open possibility for different discussions on the experimental result by introducing numerical relationships between the concentration of the native defects and the curing condition.