• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.127-134
• /
• 2020

High supersonic aircraft are exposed to high temperature environments by aerodynamic heating during supersonic flight. Thermal protection system structures such as double-panel structures are used on the skin of the fuselage and wings to prevent the transfer of high heat into the interior of an aircraft. The thin-walled double-panel skin can be exposed to acoustic loads by supersonic aircraft's high power engine noise and jet flow noise, which can cause sonic fatigue damage. Therefore, it is necessary to examine the behavior of supersonic aircraft skin structure under thermal-acoustic load and to predict fatigue life. In this paper, we designed and fabricated thermal-acoustic test equipment to simulate thermal-acoustic load. Thermal-acoustic testing of the titanium specimen under thermal-acoustic load was performed. The analytical model was verified by comparing the thermal-acoustic test results with the finite element analysis results.

• Journal of Hospice and Palliative Care
• /
• v.19 no.3
• /
• pp.201-210
• /
• 2016

Delirium is a common symptom in patients with terminal cancer. The prevalence increases in the dying phase. Delirium causes negative effects on quality of life for both patients and their families, and is associated with higher mortality. However, some studies reported that it tends to remain unrecognized in palliative care setting. That may be related with difficulties to distinguish the symptom from others with overlapping characteristics such as depression and dementia, and a lack of knowledge regarding assessment and diagnostic tools. We suggest that accurate recognition with validated tools and early diagnosis of the symptom should be highly prioritized in delirium management in palliative care setting. After diagnosing delirium, it is important to identify and address reversible precipitants such as medication, dehydration, and infection. Non-pharmacological interventions including comfortable environment for the patient and family education are also essential in the management strategy. If such interventions prove ineffective or insufficient to control hyperactive symptoms, pharmacologic interventions with antipsychotics and benzodiazepine can be considered. Until now, low levels of haloperidol remains the standard treatment despite a lack of evidence. Atypical antipsychotics such as olanzapine, quetiapine and risperidone reportedly have similar efficacy with a stronger sedating property and less adverse effect compared to haloperidol. Currently, delirium medications that can be used in palliative care setting require more clinical trials, and thus, clinical guidelines are not sufficiently available. We suggest that it is warranted to develop clinical guidelines based on well-designed clinical studies for palliative care patients.

• Korean Journal of Ecology and Environment
• /
• v.49 no.3
• /
• pp.187-196
• /
• 2016

This study was performed to improve the foaming generated in the effluent of wastewater treatment plant from March 2015 to July 2016. The main cause of foaming was air entrainment by an impinging jet and the internal accumulation by the diffusion barrier. Particularly, the foam growth was most active when there is low tide and larger discharge. To solve this problem, we experimented after installing fine mesh screen and the artificial channel device with underwater discharging outlet in the treated wastewater discharge channel and the outlet, respectively. As a result, the effects of foam reduction by devices ranged 85.0~92.0% and 70.7~85.6%, respectively. In addition, the foam and the noise were easily solved, first of all look to contribute to the prevention of complaints. Our device studies were applied to a single wastewater treatment plant. However, it is considered to be able to apply in other similar cases of domestic sewage treatment plants.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.1
• /
• pp.73-81
• /
• 2018

The quality of side scan sonar images is determined by the frequency of a sonar. A side scan sonar with a low frequency creates low-quality images. One of the factors that lead to low quality is a high-level noise. The noise is occurred by the underwater environment such as equipment noise, signal interference and so on. In addition, in order to compensate for the transmission loss of sonar signals, the received signal is recovered by TVG (Time-Varied Gain), and consequently the side scan sonar images contain non-homogeneous noise which is opposite to optic images whose noise is assumed as homogeneous noise. In this paper, the SSCS (Structural Sparsity based Compressive Sensing) is proposed for removing non-homogeneous noise. The algorithm incorporates both local and non-local models in a structural feature domain so that it guarantees the sparsity and enhances the property of non-local self-similarity. Moreover, the non-local model is corrected in consideration of non-homogeneity of noises. Various experimental results show that the proposed algorithm is superior to existing method.

• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.53-68
• /
• 1996

마그네슘이 자동차 경량화에 관심이 되는 이유는 근본적으로 CAFE 규제와 같이 경량화를 통한 화석연료의 소모를 크게 억제해야 한다는 사회적인 규제이나, 지난 10여년간의 기술발전으로 내식성이 나쁘다거나 취급이 위험한 금속이라는 인식이 크게 개선된 데에도 있다. 다른 경량금속에 대한 Mg 지금 가격의 비교조건이 호전되었고 향후 원소 재공급의 다변화가 추진되고 있는 것도 환경을 변화시킨 중요한 요인이다. 그간 중요한 경량화 대체 재료로 연구투자가 많았던 유기고분자 재료 및 FRP 등과 같은 복합재료는 폐기부품의 재활용이 어려움 때문에 호나경친화적인 단점이 부각되어, 이 소재의 증가가 주춤해 있다. 마그네슘의 경우에는 재활용이 가능하고, 진동흡수효과가 매우 커서 소음발생을 크게 줄일 뿐만 아니라, 주행 및 내구성시험에서 치수안정성이 좋고 많은 종류의 전자기기 사용에 의한 전자파 차폐효과도 큰 장점을 가지고 있다. 본 고에서는 Mg 다이캐스팅으로 자동차부품의 경량화 현황과 선진국에서 보는 전망을 미국을 중심으로 정리하고, 이와 관련한 Mg 다이캐스팅으로 자동차부품의 경량화 현황과 선진국에서 보는 전망을 미국을 중심으로 정리하고, 이와 관련한 Mg 기술적인 이슈와 시장전망도 서술하였다. 그리고 현재 우리나라의 연구계와 부품업계에서 추진하고 있는 연구개발 동향을 자동차 업계에 소개하는 의미도 있다. 이처럼 우리나라의 현황을 정리해 보는 것은 국내 자동차 산업이 국제적인 경쟁을 하고 있고 Mg기술과 원료확보에서 일본의 견제를 받고 있는 우리의 현실에서도 필요한 작업으로 생각된다.값들로 구성되는 형상을 내구 성능, 성형성등을 고려하여 최종 형상으로 결정한다. 내구성능의 예측은 금속부품의 내구수명 예측에 널리 이용되고 있는 방법이 방진 고무부품의 경우에도 적용 가능한지를 검토하고, 방진 고무부품에도 일반적으로 적용될수 있는 내구수명 예측방안의 개발 가능성을 타진해 보았다. 본 연구의 목표는 시제품을 제작하기 이전에 설계된 부품에 대한 스프링 상수 및 내구특성을 체계적으로 규명하여 제품 시험의 횟수를 줄이고, 보다 정밀한 제품을 제작할 수 있도록 하기 위한 것이다.세포수는 초기 배반포기배에서 팽윤 배반포기배로 진행됨에 따라 두배에서 세배 정도 증가되었음을 알 수 있었다. 또한, differential labelling과 bisbenzimide기법에서 얻어진 각각의 총세포수를 비교하였을 때 총세포수는 발달의 진행 정도에 따라 증가되며 그와 동시에 동일한 군 간의 세포수도 거의 유사함을 알 수 있었다. 따라서, ICM과 TE를 differential labelling하는 기법은 수정란의 quality를 평가하는데 매우 유용한 기법으로서 착상전 embryo 발달을 연구하는데 효과적으로 이용될 수 있다는 것을 시사한다. 고도의 유의차를 나타낸 반면 비수구, 초생수로구 및 Bromegrass 목초구 간에는 아무런 유의차가 인정되지 않았다. 7. 농지보전 처리구인 배수구와 초생수로구는 비처리구에 비해 낮은 침두 유출량과 낮은 토양유실량을 나타내었다.구보다 14% 절감되는 것으로 나타났다.작용하는 것으로 사료된다.된다.정량 분석한 결과이다. 시편의 조성은 33.6 at%

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.195-200
• /
• 2020

With the growing interest in fossil fuel depletion and environmental pollution, railroad cars operating in Korea are in progress as the conversion from diesel to electric vehicles expands. The photovoltaic system, which is applied as an example of the conversion of electric vehicles, is infinite and pollution-free, and can produce energy without generating hazards such as air pollution, noise, heat, and vibration, and maintain fuel transportation and power generation facilities. There is an advantage that is rarely needed. However, the amount of electricity produced depends on the amount of solar radiation by region, and the energy density is low due to the power generation of about 25㎡/ kWp, so a large installation area is required and the installation place has limited problems. In view of these problems, many studies have been applied to fuel cells in the railway field. In particular, the plan to link the fuel cell power generation system railroad power supply system must be linked to the power supply system that supplies power to the railroad, unlike solar and wind power. Therefore, it has a close relationship with railroad cars and the linkage method can vary greatly depending on the system topology. Therefore, in this paper, we study the validity through simulation modeling related to linkage analysis according to system topology.

• The Korean Journal of Air & Space Law and Policy
• /
• v.28 no.2
• /
• pp.145-181
• /
• 2013

General aviation is an integral part of civil aviation and involves the widest range of aviation segments except commercial aviation. Featured with different operational procedures and practices to satisfy the economic needs and safety requirements of a sovereign state, general aviation tends to be regulated by an individual state. The last three decades have seen exponential growth of commercial air transport in China, but its general aviation sector has remained disproportionally underdeveloped. With the deepening of the reform of low-altitude airspace, the sector is poised for a radical change and rapid growth. However, legislation governing general aviation activities in China is distorted causing inconsistency and confusions in their application and implementation. This paper aims to analyse China's prevailing legislation regulating general aviation activities. It first discusses the various definitions adopted by ICAO and its member states and reviews the development of general aviation in the US, EU, Australia and China. It then examines the sources of China's general aviation laws, e.g. Chicago Convention and its annexes, and Chinese domestic legislature which covers legislation, laws, directives, rules and procedures. The paper continues to analyse and establish the deficiencies of its prevailing legal framework by pointing out the following: variation of definitions in different regulations, inconsistency of principles in existing laws and regulations, legal vacuum concerning government subsidy, environment protection, safety and security, and other operational areas such as aerial club, sightseeing, and search and rescue. In this process, the paper argues that a coherent, consistent and systematic legal framework is required in order to ensure fair competition and safety for a healthy, progressive and sustainable general aviation growth. Suggestions for rectification and improvement are proposed.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.1
• /
• pp.30-38
• /
• 2017

In this paper, we propose an underwater acoustic sensor fault detection method for passive sonar systems. In general, a passive sonar system displays processed results of array signals obtained from tens of the acoustic sensors as a two-dimensional image such as displays for broadband or narrowband analysis. Since detection result display in the operation software is to display the accumulated result through the array signal processing, it is difficult to determine the possibility where signal may be contaminated by the fault or failure of a single channel sensor. In this paper, accordingly, we propose a detection method based on the analysis of RMSCR (Root Mean Square Crossing-Rate), and the processing techniques for the faulty sensors are analyzed. In order to evaluate the performance of the proposed method, the precision of detecting fault sensors is measured by using signals acquired from real array being operated in several coastal areas. Besides, we compare performance of fault processing techniques. From the experiments, it is shown that the proposed method works well in underwater environments with high average RMS, and mute (set to zero) shows the best performance with regard to fault processing techniques.

• 월간산업보건
• /
• s.5
• /
• pp.4-15
• /
• 1988

In order to proffer the fundamental data for the better working environment and the effective establishment of hearing conservation program on workers exposed to industrial noise, author assessed noise levels on the 42 noisy processes among 84 manufactures of 9 industries and measured noise gearing loss by the type of industries on 3,104 workers at these noisy processes from March, 1986 to Februry, 1987. The results were summarized as follows: 1. The averge of A-weight sound level of 23 processes(54.8%) and the avergae of sound level at each octave band of 14 processes(33.3%) exceeded the permissible exposure limits in 8 hours per day. 2. The noise level was the highest in process of cocking of ship building(109.1dBA), and followed by plating of steel rolling(104.3dBA), rivet of manufacture of motor vehicles(102.5dBA), shot of ship building(98.5dBA), aciding(95.7BA) and steel tubing(95.0dBA) of steel rolling, weaving of textiles(95.0dBA). 3. The permissible exposure time for the average of sound level at each octave band was only 30 minutes in the process of cocking of ship building, plating of steel rolling and rivet of manufacture of motor vehicles. 4. As a result of audiometric examination in 3,104 workers, the rate of hearing loss over 50dB at 4,000Hz was 7.3%(227 workers) and the rate of hearing loss over 41dB at 60average method was 2.9%(89 workers). 5. The prevalence of occupational hearing loss in ship building and manufacture of motor vehicle was 5.2% and it was the highest among prevalence of these 9 industries. 6. As a result of this suvery, the noise control and gearing conservation program were required especially in the industry of ship building and manufacture of motor vehicle.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.93-101
• /
• 2017

The shortage of parking lots in aged apartment complexes built from the 1980s to the mid 1990s is serious. When we look at the case of parking lot expansion in the aged apartment complexes, the method of extending the underground parking lot vertically occupies the majority. It is very important to secure the structural safety of the foundations when the existing buildings are enlarged. In the case of underground vertical work, the work space should be narrow, so that a method with excellent safety, environmental and construction properties should be applied. Urban construction is also required to use construction methods and equipment with low noise and vibration. This study analyzed the factors influencing the selection of the foundation reinforcement method for the expansion of the underground parking lot and Weights of influence factors were calculated. The purpose of this study was to analyze the applicability of the foundation reinforcement method. Factors influencing the applicability of the foundation reinforcement method were derived through expert interviews and The AHP technique was used to calculate the weight of the influencing factors. It was evaluated by experts on the applicability of the foundation reinforcement method. It conducted a case study on two types of underground parking lot expansion type and compared the applicability of the foundation reinforcement method.