• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.201-209
• /
• 2010

Generally, PSC girder bridge uses total gross cross section to resist applied loads unlike reinforced concrete member. Also, it is used as short and middle span (less than 30 m) bridges due to advantages such as ease of design and construction, reduction of cost, and convenience of maintenance. But, due to recent increased public interests for environmental friendly and appearance appealing bridges all over the world, the demands for longer span bridges have been continuously increasing. This trend is shown not only in ordinary long span bridge types such as cable supported bridges but also in PSC girder bridges. In order to meet the increasing demands for new type of long span bridges, PSC hollow box girder with H-type steel as compression reinforcements is developed for bridge with a single span of more than 50 m. The developed PSC girder applies compressive prestressing at H-type compression reinforcements using unbonded PS tendon. The purpose of compressive prestressing is to recover plastic displacement of PSC girder after long term service by releasing the prestressing. The static test composed of 4 different stages in 3-point bending test is performed to verify safety of the bridge. First stage loading is applied until tensile cracks form. Then in second stage, the load is removed and the girder is unloaded. In third stage, after removal of loading, recovery of remaining plastic deformation is verified as the compressive prestressing is removed at H-type reinforcements. Then, in fourth stage, loading is continued until the girder fails. The experimental results showed that the first crack occurs at 1,615 kN with a corresponding displacement of 187.0 mm. The introduction of the additional compressive stress in the lower part of the girder from the removal of unbonded compressive prestressing of the H-type steel showed a capacity improvement of about 60% (7.7 mm) recovery of the residual deformation (18.7 mm) that occurred from load increase. By using prestressed H-type steel as compression reinforcements in the upper part of cross section, repair and rehabilitation of PSC girders are relatively easy, and the cost of maintenance is expected to decrease.

• Journal of Venture Innovation
• /
• v.6 no.1
• /
• pp.181-198
• /
• 2023

This study aims to analyze the influence of organizational support perception of workers in medical institutions on intrinsic job motivation, and to check whether there is significance in the mediating effect of work-family conflict and work-family balance factors in this process. The results of empirical analysis through the questionnaire are as follows. First, it was confirmed that organizational support recognition had a significant positive effect on work-family balance as well as intrinsic job motivation, and work-family balance had a significant positive effect on intrinsic job motivation. Second, it was confirmed that organizational support recognition had a significant negative effect on work-family conflict, but work-family conflict had no significant influence on intrinsic job motivation. Third, in order to reduce job stress for medical institution workers, it is necessary to reduce job intensity, assign appropriate workload for ability. And in order to improve manpower operation and job efficiency, Job training and staffing in the right place are needed. Fourth, in order to improve positive organizational support perception and intrinsic job motivation, It is necessary to induce long-term service by providing support and institutional devices to increase attachment to the current job and recognize organizational problems as their own problems with various incentive systems. The limitations of this study and future research directions are as follows. First, it is believed that an expanded analysis of medical institution workers nationwide by region, gender, medical institution, academic, and income will not only provide more valuable results, but also evaluate the quality of medical services. Second, it is necessary to reflect the impact of the work-life balance support system on each employee depending on the environmental uncertainty or degree of competition in the hospital to which medical institution workers belong. Third, organizational support perception will be recognized differently depending on organizational culture and organizational type, and organizational size and work characteristics, working years, and work types, so it is necessary to reflect this. Fourth, it is necessary to analyze various new personnel management techniques such as hospital's organizational structure, job design, organizational support method, motivational approach, and personnel evaluation method in line with the recent change in the government's medical institution policy and the global business environment. It is also considered important to analyze by reflecting recent and near future medical trends.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.52 no.1
• /
• pp.46-58
• /
• 2024

Pollinators are organisms that carry out the pollination process of plants and include Hymenoptera, Lepidoptera, Diptera, and Coleoptera. Among them, bees not only pollinate plants but also improve urban green spaces damaged by land use changes, providing a habitat and food for birds and insects. Today, however, the number of pollinating plants is decreasing due to issues such as early flowering due to climate change, fragmentation of green spaces due to urbanization, and pesticide use, which in turn leads to a decline in bee populations. The decline of bee populations directly translates into problems, such as reduced biodiversity in cities and decreased food production. Urban beekeeping has been proposed as a strategy to address the decline of bee populations. However, there is a problem asurban beekeeping strategies are proposed without considering the complex structure of the socio-ecological system consisting of bees foraging and pollination activities and are therefore unsustainable. Therefore, this study aims to analyze the socio-ecological system of honeybees, which are pollinators, structurally using system thinking and propose a green space planning strategy to revitalize urban beekeeping. For this study, previous studies that centered on the social and ecological system of bees in cities were collected and reviewed to establish the system area and derive the main variables for creating a causal loop diagram. Second, the ecological structure of bees' foraging and pollination activities and the structure of bees' ecological system in the city were analyzed, as was the social-ecological system structure of urban beekeeping by creating an individual causal loop diagram. Finally, the socio-ecological system structure of honey bees was analyzed from a holistic perspective through the creation of an integrated causal loop diagram. Citizen participation programs, local government investment, and the creation of urban parks and green spaces in idle spaces were suggestedas green space planning strategies to revitalize urban beekeeping. The results of this study differ from previous studies in that the ecological structure of bees and the social structure of urban beekeeping were analyzed from a holistic perspective using systems thinking to propose strategies, policy recommendations, and implications for introducing sustainable urban beekeeping.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.52 no.2
• /
• pp.51-63
• /
• 2024

While the government policy to fully adopt BIM in the construction sector is being implemented, the construction and utilization of landscape BIM models are facing challenges due to problems such as limitations in BIM authoring tools, difficulties in modeling natural materials, and a shortage in BIM content including libraries. In particular, plants, fundamental design elements in the field of landscape architecture, must be included in BIM models, yet they are often omitted during the modeling process, or necessary information is not included, which further compromises the quality of the BIM data. This study aimed to contribute to the construction and utilization of landscape BIM models by developing a plant library that complies with BIM standards and is applicable to the landscape industry. The plant library of trees and shrubs was developed in Revit by modeling 3D shapes and collecting attribute items. The geometric information is simplified to express the unique characteristics of each plant species at LOD200, LOD300, and LOD350 levels. The attribute information includes properties on plant species identification, such as species name, specifications, and quantity estimation, as well as ecological attributes and environmental performance information, totaling 24 items. The names of the files were given so that the hierarchy of an object in the landscape field could be revealed and the object name could classify the plant itself. Its usability was examined by building a landscape BIM model of an apartment complex. The result showed that the plant library facilitated the construction process of the landscape BIM model. It was also confirmed that the library was properly operated in the basic utilization of the BIM model, such as 2D documentation, quantity takeoff, and design review. However, the library lacked ground cover, and had limitations in those variables such as the environmental performance of plants because various databases for some materials have not yet been established. Further efforts are needed to develop BIM modeling tools, techniques, and various databases for natural materials. Moreover, entities and systems responsible for creating, managing, distributing, and disseminating BIM libraries must be established.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.6
• /
• pp.583-603
• /
• 2023

Recently, the advancement of mechanical tunnel boring machine (TBM) technology and the characteristics of subsea railway tunnels subjected to hydrostatic pressure have led to the widespread application of shield TBM methods in the design and construction of subsea railway tunnels. Subsea railway tunnels are exposed in a constant pore water pressure and are influenced by the amplification of seismic waves during earthquake. In particular, seismic loads acting on subsea railway tunnels under various ground conditions such as soft ground, soft soil-rock composite ground, and fractured zones can cause significant changes in tunnel displacement and stress, thereby affecting tunnel safety. Additionally, the dynamic response of the ground and tunnel varies based on seismic load parameters such as frequency characteristics, seismic waveform, and peak acceleration, adding complexity to the behavior of the ground-tunnel structure system. In this study, a finite difference method is employed to model the entire ground-tunnel structure system, considering hydrostatic pressure, for the investigation of dynamic behavior of subsea railway tunnel during earthquake. Since the key factors influencing the dynamic behavior during seismic events are ground conditions and seismic waves, six analysis cases are established based on virtual ground conditions: Case-1 with weathered soil, Case-2 with hard rock, Case-3 with a composite ground of soil and hard rock in the tunnel longitudinal direction, Case-4 with the tunnel passing through a narrow fault zone, Case-5 with a composite ground of soft soil and hard rock in the tunnel longitudinal direction, and Case-6 with the tunnel passing through a wide fractured zone. As a result, horizontal displacements due to earthquakes tend to increase with an increase in ground stiffness, however, the displacements tend to be restrained due to the confining effects of the ground and the rigid shield segments. On the contrary, peak compressive stress of segment significantly increases with weaker ground stiffness and the effects of displacement restrain contribute the increase of peak compressive stress of segment.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.3
• /
• pp.40-46
• /
• 2009

The applicability of a well-type autotrophic sulfur-oxidizing reactive barrier (L $\times$ W $\times$ D = $3m\;{\times}\;4\;m\;{\times}\;2\;m$) as a long-term treatment option for nitrate removal in groundwater was evaluated. Pilot-scale (L $\times$ W $\times$ D = $8m\;{\times}\;4\;m\;{\times}\;2\;m$) flow-tank experiments were conducted to examine remedial efficacy of the well-type reactive barrier. A total of 80 kg sulfur granules as an electron donor and Thiobacillus denitrificans as an active bacterial species were prepared. Thiobacillus denitrificans was successfully colonized on the surface of the sulfur granules and the microflora transformed nitrate with removal efficiency of ~12% (0.07 mM) for 11 days, ~24% (1.3 mM) for 18 days, ~45% (2.4 mM) for 32 days, and ~52% (2.8 mM) for 60 days. Sulfur granules attached to Thiobacillus denitrificans were used to construct the well-type reactive barrier comprising three discrete barriers installed at 1-m interval downstream. Average initial nitrate concentrations were 181 mg/L for the first 28 days and 281 mg/L for the next 14 days. For the 181 mg/L (2.9 mM) plume, nitrate concentrations decreased by ~2% (0.06 mM), ~9% (0.27 mM), and ~15% (0.44 mM) after $1^{st}$, $2^{nd}$, and $3^{rd}$ barriers, respectively. For the 281 mg/L (4.5 mM) plume, nitrate concentrations decreased by ~1% (0.02 mM), ~6% (0.27 mM), and ~8% (0.37 mM) after $1^{st}$, $2^{nd}$, and $3^{rd}$ barriers, respectively. Nitrate plume was flowed through the flow-tank for 49 days by supplying $1.24\;m^3/d$ of nitrate solution. During nitrate treatment, flow velocity (0.44 m/d), pH (6.7 to 8.3), and DO (0.9~2.8 mg/L) showed little variations. Incomplete destruction of nitrate plume was attributed to the lack of retention time, rarely transverse dispersion, and inhibiting the activity of denitrification enzymes caused by relatively high DO concentrations. For field applications, it should be considered increments of retention time, modification of well placements, and intrinsic DO concentration.

• Journal of agricultural medicine and community health
• /
• v.26 no.1
• /
• pp.37-56
• /
• 2001

This study was conducted to analyze the degree of changes in knowledge and attitude toward smoking and to examine the factors affecting knowledge and attitude for smoking after providing a smoking prevention program based on social influence model for a year to middle school students. Study population consists of 665 subjects of middle school students(aged 14 years) in Gumi city in Kyeongsangbukdo Province. Among them three-hundred sixty-seven students(intervention group) were educated to a smoking prevention program for 1 year from April 1999 to April 2000. School-based four-class program to prevent smoking was developed. The program provides instruction about short and long-term negative physiologic and social consequences of smoking and also discussed the health hazards of smoking, social pressure to smoke, peer norms regarding tobacco use, and refusal skill. A 45-item self-administered structured questionnaire was designed to evaluate the change of knowledge, attitude, smoking rate and the amount of smoking. The instrument was comprised of 11 knowledge items, thirteen attitude item and demographic items. Each scales were created by summing responses to each items within each scales and high scores on the knowledge, attitude, and smoking behavioral intention scales indicated positive responses. Based on the changes before and after the implementation of smoking prevention program between intervention and control group, the change of scores on knowledge were significantly different between the control group and the intervention group(p<0.05) and the change of scores on the attitude toward smoking was significantly different between intervention and control group. The change of smoking rate were not showing a significant difference between two groups but the amount of smoking were significantly reduced in intervention group than control group. In multiple regression analysis on changes of knowledge about smoking, the variables of smoking prevention program education, previous knowledge on smoking and students' school performance were selected the significant variables. In multiple regression to analysis of the factors influencing changes in attitude toward smoking, the variables of smoking prevention program education, previous knowledge on smoking were shown to be significant. The smoking prevention program was effective on change of knowledge and attitude of middle school students. In considering that the policy should be needed to extent of implementation of school-based health education curricula based on social influence model and it would contribute to reduce smoking of students.

• Journal of Intelligence and Information Systems
• /
• v.20 no.3
• /
• pp.45-58
• /
• 2014

The Korean Culture Contents spread out to Worldwide, because the Korean wave is sweeping in the world. The contents stand in the middle of the Korean wave that we are used it. Each country is ongoing to keep their Culture industry improve the national brand and High added value. Performing contents is important factor of arousal in the enterprise industry. To improve high arousal confidence of product and positive attitude by populace is one of important factor by advertiser. Culture contents is the same situation. If culture contents have trusted by everyone, they will give information their around to spread word-of-mouth. So, many researcher study to measure for person's arousal analysis by statistical survey, physiological response, body movement and facial expression. First, Statistical survey has a problem that it is not possible to measure each person's arousal real time and we cannot get good survey result after they watched contents. Second, physiological response should be checked with surround because experimenter sets sensors up their chair or space by each of them. Additionally it is difficult to handle provided amount of information with real time from their sensor. Third, body movement is easy to get their movement from camera but it difficult to set up experimental condition, to measure their body language and to get the meaning. Lastly, many researcher study facial expression. They measures facial expression, eye tracking and face posed. Most of previous studies about arousal and interest are mostly limited to reaction of just one person and they have problems with application multi audiences. They have a particular method, for example they need room light surround, but set limits only one person and special environment condition in the laboratory. Also, we need to measure arousal in the contents, but is difficult to define also it is not easy to collect reaction by audiences immediately. Many audience in the theater watch performance. We suggest the system to measure multi-audience's reaction with real-time during performance. We use difference image analysis method for multi-audience but it weaks a dark field. To overcome dark environment during recoding IR camera can get the photo from dark area. In addition we present Multi-Audience Engagement Index (MAEI) to calculate algorithm which sources from sound, audience' movement and eye tracking value. Algorithm calculates audience arousal from the mobile survey, sound value, audience' reaction and audience eye's tracking. It improves accuracy of Multi-Audience Engagement Index, we compare Multi-Audience Engagement Index with mobile survey. And then it send the result to reporting system and proposal an interested persons. Mobile surveys are easy, fast, and visitors' discomfort can be minimized. Also additional information can be provided mobile advantage. Mobile application to communicate with the database, real-time information on visitors' attitudes focused on the content stored. Database can provide different survey every time based on provided information. The example shown in the survey are as follows: Impressive scene, Satisfied, Touched, Interested, Didn't pay attention and so on. The suggested system is combine as 3 parts. The system consist of three parts, External Device, Server and Internal Device. External Device can record multi-Audience in the dark field with IR camera and sound signal. Also we use survey with mobile application and send the data to ERD Server DB. The Server part's contain contents' data, such as each scene's weights value, group audience weights index, camera control program, algorithm and calculate Multi-Audience Engagement Index. Internal Device presents Multi-Audience Engagement Index with Web UI, print and display field monitor. Our system is test-operated by the Mogencelab in the DMC display exhibition hall which is located in the Sangam Dong, Mapo Gu, Seoul. We have still gotten from visitor daily. If we find this system audience arousal factor with this will be very useful to create contents.

• Food Science of Animal Resources
• /
• v.27 no.4
• /
• pp.392-400
• /
• 2007

This experiment was conducted to evaluate effects of various periods of rye silage feeding on the growth performance, blood characteristics, and carcass quality of finishing pigs. A total of sixteen [($Landrace{\times}Yorkshire{\times}Duroc$)] pigs (90.26 kg in average initial body weight) were tested in individual cages for a 30 day period. Dietary treatments included 1) CON (basal diet), 2) S10 (basal diet for 20 days and 3% rye silage for 10 days) 3) S20 (basal diet for 10 days and 3% rye silage for 20 days) and 4) S30 (3% rye silage for 30 days). There were no significant differences in the ADG and gain/feed ratio among the treatments(p>0.05), however the ADFI was higher in pigs fed the CON diet than with pigs fed diets with rye silage (p<0.05). The DM digestibility was higher with the S20 diet than with the S30 diet (p<0.05). With regard to blood characteristics, pigs fed rye silage had a significantly reduced cortisol concentration compared to pigs fed the CON diet (p<0.05). The backfat thickness was higher with the CON diet than with the S20 or S30 diets (p<0.05). Regarding the fatty acid contents of the leans, the C18:0 and total SFA were significantly higher with the CON diet than with the other diets (p<0.05). However, the C18:1n9, total MUFA and UFA/SFA levels were significantly lower with the CON diet than the other diets (p<0.05). Regarding the fatty acid contents of fat, the levels of C18:1n9 and MUFA were similar with the S20 and S30 diets, however, these levels were higher than with the CON or S10 diets (p<0.05). In conclusion, feed intake and DM digestibility were affected by rye silage, and the cortisol concentration, backfat thickness and fatty acid composition of pork were positively affected by feeding pigs rye silage.

• The Korean Journal of Archival Studies
• /
• no.26
• /
• pp.103-149
• /
• 2010

Documentation strategy has been experimented in various subject areas and local regions since late 1980's when it was proposed as archival appraisal and selection methods by archival communities in the United States. Though it was criticized to be too ideal, it needs to shed new light on the potentialities of the strategy for documenting local regions in digital environment. The purpose of this study is to analyse the implementation issues of documentation strategy and to suggest the directions for documenting local regions of Korea through the application of the strategy. The documentation strategy which was developed more than twenty years ago in mostly western countries gives us some implications for documenting local regions even in current digital environments. They are as follows; Firstly, documentation strategy can enhance the value of archivists as well as archives in local regions because archivist should be active shaper of history rather than passive receiver of archives according to the strategy. It can also be a solution for overcoming poor conditions of local archives management in Korea. Secondly, the strategy can encourage cooperation between collecting institutions including museums, libraries, archives, cultural centers, history institutions, etc. in each local region. In the networked environment the cooperation can be achieved more effectively than in traditional environment where the heavy workload of cooperative institutions is needed. Thirdly, the strategy can facilitate solidarity of various groups in local region. According to the analysis of the strategy projects, it is essential to collect their knowledge, passion, and enthusiasm of related groups to effectively implement the strategy. It can also provide a methodology for minor groups of society to document their memories. This study suggests the directions of documenting local regions in consideration of current archival infrastructure of Korean as follows; Firstly, very selective and intensive documentation should be pursued rather than comprehensive one for documenting local regions. Though it is a very political problem to decide what subject has priority for documentation, interests of local community members as well as professional groups should be considered in the decision-making process seriously. Secondly, it is effective to plan integrated representation of local history in the distributed custody of local archives. It would be desirable to implement archival gateway for integrated search and representation of local archives regardless of the location of archives. Thirdly, it is necessary to try digital documentation using Web 2.0 technologies. Documentation strategy as the methodology of selecting and acquiring archives can not avoid subjectivity and prejudices of appraiser completely. To mitigate the problems, open documentation system should be prepared for reflecting different interests of different groups. Fourth, it is desirable to apply a conspectus model used in cooperative collection management of libraries to document local regions digitally. Conspectus can show existing documentation strength and future documentation intensity for each participating institution. Using this, documentation level of each subject area can be set up cooperatively and effectively in the local regions.