• KIEAE Journal
• /
• v.12 no.5
• /
• pp.3-10
• /
• 2012

In this study, the influence of decentralized rainwater management over the changes in evapotranspiration was analyzed. The analysis method was obtained by establishing the decentralized rainwater management plan according to different scenarios, and subsequently examined evapotranspiration in the plan. Scenario 1 refers to the analysis of the existing situation, in which was 100% of a parking lot is asphalt pavement. In Scenario 2, the pavement of the parking surface in the parking lot is replaced with lawn blocks. In Scenario 3, some asphalt pavement was removed to establish a flower-bed type infiltration system to allow rainwater to permeate. In Scenario 4, infiltration and storage of rain water would be achieved by transforming the parking surface into lawn blocks, keeping the asphalt for the parking road while establishing a vegetation strip. The amount of evapotranspiration of the target site was analyzed with a water budget analysis program (CAT) using the 2001 meteorological data for each scenario According to the analysis values of S2 and S3, it was found that evapotranspiration is critically affected by the amount of area replaced with pervious area in the total target site. An energy equivalent to 680kWh is required for 1 ton of water to evaporate. Hence, it can be seen that the active inducement of evapotranspiration in urban area makes a positive contribution not only to heat island mitigation, but also to the small-scale water circulation process in a city.

• KIEAE Journal
• /
• v.12 no.5
• /
• pp.53-61
• /
• 2012

As aging society progresses, it is necessary to establish a housing standard that provides a healthy, safe, and convenient environment for the elderly. The objective of the study is to propose a housing space standard that is geared towards elderly living in the urban area. Three steps were taken to attain the objective. First, characteristics of housing preference, spatial usage and furniture preference of the elderly were attained through a survey. The survey was conducted targeting the respondents of the ages 60 to 79 living in three different administrative districts in Seoul. Second, the required floor space to perform individual specific behavior using anthropometric dimension of the elderly was investigated by literature review. Lastly, floor space of each space is suggested combining each area for individual specific behavior which reflects characteristics of housing preference and spatial usage. The results of the research as follows. A bedroom was planned, which includes the function of receiving guests by giving the area for the placement of a sofa. The space for the use of dinning table for two person was planned in the kitchen and The space for the behavior of showering on a chair was planned in a bathroom. Lastly, the space for the behavior of taking off shoes on a chair was considered in the entrance area. Consequently, $35.4m^2$ is suggested as the necessary floor space for the elderly housing considering the characteristics of the elderly in urban area. However, because of space composition and space for accessibility, the additional space should be considered to plan the elderly housing.

• Journal of Families and Better Life
• /
• v.29 no.5
• /
• pp.1-17
• /
• 2011

This study aimed to analyze health promotion villages from the perspective of therapeutic architecture, and to provide basic information for planning relevant health facilities. On the basis of a review of previous literature, the characteristics of therapeutic architecture were classified into eight categories: safety, comfort, sociality, autonomy, openness, diversity, privacy, and natural environment. Field study and observation were performed in four health promotion villages that conduct programs for lifestyle improvement, physical fitness, and treatment; these villages were also considered to have a healthy residential environment. The researcher and three assistants visited the facilities and checked utilization of space through interviews with the staff and guided tours. Basic information about the subject facilities, such as the purpose of establishment, was gathered from websites before visits. Two of the villages examined in this study had a traditional Korean wooden structure, while the other two were reinforced concrete and masonry block structures. All the facilities emphasized the use of environmentally friendly material and harmony with nature. Each site was divided into the following areas: office, residence, health/treatment, public/rest, and outdoor. The safety standards of the healing architecture were not completely satisfactory at all facilities. In particular, it was found that they lacked adequate universal design equipment. However, the healing characteristics of autonomy and diversity were strong. With regard to autonomy, the facilities allowed visitors to select indoor-outdoor moving lines and the use of front- and backyards constructed on slopes. In addition, they were equipped with many entries, staircases, void, terraces, and crossroads. The architecture was aesthetically designed using feng shui symbolism, and visitors found the scenes depicted in various spaces in the villages to be stimulating. Besides, the facilities were constructed using natural materials, had a natural indoor environment, and provided a sense of spaciousness and flexibility.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.766-771
• /
• 2012

PC (polycarbonate) is one of the widely used engineering plastics. Polycarbonate (PC) is traditionally produced by the reaction of phosgene and bisphenol-A. This phosgene process has the disadvantage as the high toxicity and corrosiveness of phosgene. The main point of focus to overcome the disadvantage of phosgene based process has been a route through dimethyl carbonate (DMC) to diphenyl carbonate (DPC). In this paper, for the DPC synthesis reaction using PBO as a catalyst, the effect of reaction temperature, reactant ratio, catalyst concentration on the reaction yield was investigated. A kinetic model for the DPC synthesis reaction was proposed and kinetic parameters for the proposed model was determined from batch reactor experiments. The predicted results by the proposed model were in good agreement with the experimental results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.377-386
• /
• 2013

As apartments have been made into high-rise buildings, the residents in the buildings have become to enjoy the benefits. On the contrary, the users of buildings on the back have become to experience many problems in residential environments. This research studied on measures to improve height control systems focusing on the heights of apartments in order to figure out the impact of apartments on city scenery. This study concluded that, to solve these problems, a general system to control heights should be prepared to solve the problem of visual blocking and for apartment complexes or buildings in coastal areas, regulations for height controls suitable to them should be separately prepared thereby controlling systems related to height controls as a whole instead of those many different systems relating to heights.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.131-140
• /
• 2016

Recent destructions of outdoor signboards have frequently been caused by strong wind, resulting in damage on the property and human livelihood. One of the major causes of the problems is inadequate implementation of structural design code to the outdoor signboards which are vulnerable to wind. This leads to this paper to present the design guideline of wind-resistant outdoor signboards. In order to estimate the design wind speed, basic wind speeds over Korea suggested by KBC(2015)(revision) are corrected with land surface roughness and topography of the terrain and installation height of the signboard. This paper also suggested the procedure of wind load estimation for different types of outdoor signboards; wall attached type, wall ribbed type and ground erected type. Since the process involves complex calculation to some extent, this paper presents summarized version of wind load estimation from non-professional point of view.

• KIEAE Journal
• /
• v.17 no.2
• /
• pp.45-51
• /
• 2017

Purpose: Housing is the most essential element for well-being in a society. The government would continuously supply decent housings to make a better living condition for people. As various housing policies have been implemented into practice, the effectiveness of policies need to be assessed and improved to rearrange the financial resources. The indicators, such as quality of life, housing supply amount and etc, could be used to estimate housing policy to provide a guidance for a new policy direction. Though various indicators are utilized to assess the policy effect, most of the items are depend upon a relativeness in aspect to assessment goal, items, time and its weighting. Therefore, it needs an absolute indicator to compare the policy effectiveness regardless of time elapse or items. In this paper, it developed the housing welfare indicator to assess the level of living condition, utilizing the Gini coefficient which is used for explanation on income distribution. Method: To suggest an inequity indicator, this paper used Gini coefficient to explain the level of living condition which is used on economics to provide the level of income distribution. Data are collected through the Korea Housing Survey by Ministry of Land, Infrastructure and Transport between 2006 and 2014. Indicators of living condition focused on the development of the estimation model using the frequency of room use. Result: Gini coefficient between 2004 and 2014 is about 1.5 score except in year 2013, and the trend of score has been decreased slowly which means the inequality gradually improved. In this result, it implies the living condition and distribution level would be improved than before.

• KIEAE Journal
• /
• v.17 no.2
• /
• pp.29-34
• /
• 2017

Purpose: Recently, significant heat loss through the window takes place in buildings. Nevertheless, there exists little literature concerning the exterior horizontal shading devices and the design criteria are not clearly settled yet. Applying the exterior horizontal shading devices is more efficient as compared to the interior shading devices in that solar radiation can be directly blocked before passing through the window or the envelope. The purpose of this study is to reduce the internal load by designing the exterior horizontal shading devices and verify the degree of reduction in energy consumption. Method: This study aims to reduce energy consumption in cooling and heating through proposing proper length and shape of the exterior horizontal shading devices in public buildings. In the process, actual energy data and the Design Builder simulation program are utilized. In addition, economic aspect is considered to figure out the optimal length of the exterior horizontal shading devices that maximizes efficiency. Result: As a result, the proper length and shape of the exterior horizontal shading devices are provided as follows: 1) Energy consumption in cooling and heating is minimized when the exterior horizontal shading devices are designed as 0.5m*2. 2) Electricity bill is the lowest when the exterior horizontal shading devices are designed as 3.3m*2. The gap between maximum and minimum electricity bill is about 7.8~14%.

• Spatial Information Research
• /
• v.23 no.1
• /
• pp.49-57
• /
• 2015

Due to high density of population and progress of high building construction technologies, the number of high buildings has been increasing. Several information services have been provided to figure out complex indoor structures of building such as indoor navigations and indoor map services. The most fundamental information for these services are indoor network information. Indoor network in building provides topological connectivity between spaces unlike geometric information of buildings. In order to make indoor network information, we have to edit network manually or derive network properties based on the geometric data of buildings. This process is not easy for complex buildings. In this paper, we suggest a method to generate indoor network automatically based on crowdsourcing. From the collected individual trajectories, we derive indoor network information with crowdsourcing. We validate our method with a sample set of trajectory data and the result shows that our method is practical if the indoor positioning technology is reasonably accurate.

• KIEAE Journal
• /
• v.15 no.1
• /
• pp.139-146
• /
• 2015

This is an experimental study on the engineering characteristics of perforated reinforced concrete beams with shells. In the material matter of this study, the water cement ratio put 60%, the ratio of substitution of oyster shells to fine aggregate 30%. And in the structural matter, the form of opening put circle and square, the size of opening as the radius and the length of it changed from one to three times of the beam depth with a change presence and absence of reinforced steel around opening. All thirteen reinforced concrete beam tests composed one standard beam and twelve six beams with the circle and square opening were tested in shear strength under two points loading and compared and analyzed the characteristics of test beams under the same conditions one another. The results of the study showed as followed. 1) The initial crack load value of the opening test beams is similar the standard beam but the maximum load value decreased with increase in proportion of the opening size, in the square opening than the circle opening and in the absence than the presence of reinforced steel. 2) As the difference between the circle opening and the square opening beams is represented 2.17~9.8% in the maximum load value and the load capacity of the square opening suddenly decrease than it of the circle opening, it is judged because of the shortage of concrete section, the concentration of the stress in the corner of the square opening and material influence of shell substitution. 3) The failure figure such as the pattern of the crack and so on is represented brittle failure as the opening size is the bigger and the ratio of substitution is higher because of the lack material properties.