• Journal of Surface Science and Engineering
• /
• v.41 no.5
• /
• pp.226-231
• /
• 2008

Titanium and its alloy have been widely used in dental implant and orthopedic prostheses. Electrochemical characteristics of dental implant in the various simulated body fluids have been researched by using electrochemical methods. Ti-6Al-4V alloy implant was used for corrosion test in 0.9% NaCl, artificial saliva and simulated body fluids. The surface morphology was observed using scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDX). The electrochemical stability was investigated using potentiosat (EG&G Co, 263A). The corrosion surface was observed using scanning electron microscopy (SEM). From the results of potentiodynamic test in various solution, the current density of implant tested in SBF and AS solution was lower than that of implant tested in 0.9% NaCl solution. From the results of passive film stability test, the variation of current density at constant 250 mV showed the consistent with time in the case of implant tested in SBF and AS solution, whereas, the current density at constant 250mV in the case of implant tested in 0.9% NaCl solution showed higher compared to SBF and AS solution as time increased. From the results of cyclic potentiodynamic test, the pitting potential and |$E_{pit}\;-\;E_{corr}$| of implant tested in SBF and AS solution were higher than those of implant tested in 0.9% NaCl solution.

• Applied Biological Chemistry
• /
• v.30 no.2
• /
• pp.179-185
• /
• 1987

The physicochemical properties and characteristics of sweet potato starches which were isolated from the six varieties were investigated. The shapes of starch granules which observed through photomicroscope and scanning electron microscope lucre round and polygonal, but those of the Shinmi were most polygonal, and the average diameters were in the range of $10.4{\sim}14.2$ microns. The amylose contents were between 25% and 28%, and blue values and alkali numbers were in the range of $0.29{\sim}0.36$, $7.0{\sim}12$, respectively. The swelling power and solubility patterns of the starches were negligible until $50^{\circ}C$, thereafter it increased rapidly and the Eunmi showed highest water binding capacity of 211.6%. Amylogram pattern of 6% starch solutions were similar to no peak viscosity, but maximum viscosity varied widely with varieties. A significant positive correlation was observed between amylose content and average gelatinization temperature. Taste and texture of the steam cooked sweet potatoes were negatively and positively correlated with moisture and amylose contents, respectively, while those of the microwave cooked sweet potatoes were only positively correlated with amylose contents.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.3
• /
• pp.79-84
• /
• 2013

The seawater pipes in the engine rooms of ships are surrounded by severely corrosive environments caused by fast flowing seawater containing chloride ions, high conductivity, etc. Therefore, it has been reported that seawater leakage often occurs at a seawater pipe because of local corrosion. In addition, the leakage area is usually welded using shielded metal arc welding with various electrodes. In this study, when seawater pipes were welded with four types of electrodes(E4311, E4301, E4313, and E4316), the difference between the corrosion resistance values in their welding zones was investigated using an electrochemical method. Although the corrosion potential of a weld metal zone welded with the E4316 electrode showed the lowest value compared to the other electrodes, its corrosion resistance exhibited the best value compared to the other electrodes. In addition, a heat affected zone welded with the E4316 electrode also appeared to have the best corrosion resistance among the electrodes. Furthermore, the corrosion resistance of the weld metal zone and heat affected zone exhibited relatively better properties than that of the base metal zone in all of the cases welded with the four types of electrodes. Furthermore, the hardness values of all the weld metal zones were higher than the base metal zone.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.1
• /
• pp.1-10
• /
• 2016

We studied the heavy minerals in 46 surface sediments collected from the Central Yellow Sea Mud (CYSM) to characterize the type, abundance, mineralogical properties and distribution pattern using the stereo-microscopy, field-Emission scanning electron microscopy (FE SEM) and chemical analysis through the energy dispersive spectrometer (EDS). Heavy mineral assemblages are primarily composed of epidote group, amphibole group, garnet group, zircon, rutile and sphene in descending order. Epidote group and amphibole group minerals account for more than 50% of total heavy minerals. The minerals in epidote group, amphibole group and garnet group in studied area are epidote, edenite and almandine, respectively. When we divided the CYSM into two regions by $124^{\circ}E$, the eastern region contain higher contents of epidote and (zircon + rutile), which are more resistant to weathering but lower of amphibole, which is less resistant to weathering than the western region. Based on this results, it is possible to estimate that the eastern region sediments are transported for a long distance while western region sediments are transported for a short distance from the source area. In the future, the additional study on the heavy minerals in river sediments flowing into the Yellow Sea and much more samples for marine sediments must be carried out to interpret exactly the provenance and sedimentation process.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.2
• /
• pp.63-72
• /
• 2014

This study is conducted to investigate mineralogical characteristics and estimate firing temperature and condition of earthenwares in the 5-6th Century which are found at ancient tombs in Gyo-dong, Gyo-ri, Changnyeong-eup, Changnyeong-gun, Gyeongsangnam-do, TKorea by applying petrological methods. For this study, mineralogical analysis, microtexture observation and chemical analysis were conducted. According to observations using a polarization microscope, the potshreds are mainly composed of quartz and feldspar and consist of some felsic volcanics, tempers, opaques and mullite, hematite and spinel were found under XRD and FTIR analysis. The flow pastes are observed in many potshreds, and it indicate that this textures made by the mixing process or the pottery made from the mixture of 2 sorts of clays at least. They dose not show the features of the potshreds firing under temperature of $1,200-1,300^{\circ}C$ rather than the earthenware firing under relatively low temperature of $1,000^{\circ}C$ approximately because of the existence of a number of pores and the crystals of the specific minerals. The growths mostly of mullite on the surface and into the cracks of the potshreds indicate that the firing condition was not uniform to make even temperature and oxidation. Most of the pottery shreds have felsic volcanic fragments and some of them have cristobalite which is formed at the temperature of more than 1,470^{\circ}C$. But considering the estimated firing temperature, these are not formed during firing but included in the original clay.

• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.251-258
• /
• 2015

In the study, PLLA with 12,000 g/mol ($M_n$) and 14,000 g/mol ($M_w$) was synthesized from L-lactide, and used to synthesize PLLA-Br intermediate. PLLA-block-PMMA with 84,000 g/mol ($M_n$) and 126,000 g/mol ($M_w$) was finally synthesized from PLLA-Br intermediate. The glass transition temperature ($T_g$) and initial pyrolysis temperature of PLLA-block-PMMA are $95.5^{\circ}C$ and $289^{\circ}C$, respectively. The PLA film of $50{\pm}3{\mu}m$ thickness was prepared by blending PLA with 9 phr PLLA-block-PMMA followed by stretching biaxially at 3 times under $95^{\circ}C$, and annealing at $120^{\circ}C$ for 2 min. The light transmittance at 550 nm and tensile strength of the film are 88.5% and 44.5 MPa, respectively. To enhance the tensile strength of PLA film, it was required to keep the film more than 2 min at $120^{\circ}C$ during the annealing step after a biaxially orientation.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.487-492
• /
• 2015

The effects of chemical structure of alkyl groups of norbornene carboxylic alkyl esters(methyl, octyl, 4-chlorobenzyl) and endo/exo ratios of norbornene monomers on activity of palladium catalyst and polymerization behavior were investigated. Norbornene ester monomers were synthesized from the reaction of 5-norborene-2-carboxylic acid and various alcohols. Polymerization catalyst, di-${\mu}$-chloro-bis(-methoxybicyclo[2,2,1]-hept-2-ene)palladium(II) (DCBMP), was synthesized according to the literature procedure and silver hexafluoroantimonate ($AgSbF_6$) was used as a conjugate anion source. Gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) were the principal techniques for polymer characterization and $^1H$ NMR spectroscopy was used for chemical structures determination of monomers and polymers. For all of the norbonene alkyl esters GPC data showed that when the amounts of endo isomers exceeded those of exo isomers decreased molecular weight polymers were obtained probably due to the decreased catalyst activity. Polymerizations were conducted by varying the monomer/catalyst mole ratios (100:1, 200:1, 300:1). When 300:1 monomer/catalyst ratio was employed it was possible to synthesize high molecular weight ($M_n=27500g/mol$), film forming polymer from exo-norbornene carboxylic acid octyl ester.

• Journal of Korean Neurosurgical Society
• /
• v.30 no.11
• /
• pp.1340-1344
• /
• 2001

This is a rare case of cerebral metastasis from malignant fibrous histiocytoma(MFH) of the soft tissue. A 62-year-old man underwent craniotomy for resection of multiple intracerebral masses under the impression of metastatic brain tumor with unknown primary site. Preoperative investigation failed to detect any extracranial lesion. At six months after the operation and whole brain radiotherapy, right shoulder mass was detected to grow and excised. Specimen from the brain and shoulder lesions revealed identical pathological findings of malignant fibrous histiocytoma except existence of glial fibrillary acidic protein(GFAP)-positive cells only in brain lesions. Palliative radiotherapy was performed for subsequently developing metastatic lesions in skeletal system. At twelve months after initial diagnosis recurrent lesion at right shoulder was detected and chemotherapy is given. This case is unique because metastatic brain lesion from MFH is rare and also cerebral metastasis as an initial manifestaion of MFH has not been reported before. Another important finding is that there was expression of GFAP only in brain lesions but not in extracranial primary site lesion. Although the presence of GFAP-positive cells is thought as one of characteristic histological findings of primary intracrainal MFH, our observation supports the hypothesis that GFAP-positive cells in primary intracranial MFH may be nonneoplastic astrocytes secondarily involved by MFH.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.653-662
• /
• 2015

In general, the coal gasification has to be operated under high temperature ($1300{\sim}1400^{\circ}C$) and pressure (30~40 bar). However, to keep this conditions, it needs unnecessary and excessive energy. In this work, to reduce the temperature of process, alkali catalysts such as $K_2CO_3$ and $Na_2CO_3$ were added into Cyprus coal. We investigated the kinetic of Cyprus char-$CO_2$ gasification. To determine the gasification conditions, the coal (with and without catalysts) gasified with fixed variables (catalyst loading, catalytic effects of $Na_2CO_3$ and $K_2CO_3$, temperatures) by using TGA. When catalysts are added by physical mixing method into Cyprus coal the reaction rate of coal added 7 wt% $Na_2CO_3$ is faster than raw coal for Cyprus char-$CO_2$ gasification. The activation energy of coal added 7 wt% $Na_2CO_3$ was calculated as 63 kJ/mol which was lower than raw char. It indicates that $Na_2CO_3$ can improve the reactivity of char-$CO_2$ gasification.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.445-451
• /
• 2010

$TiO_2$ shows considerably efficient photoreaction activity under the ultraviolet range but it has disadvantage that there is no activity in the visible light range. In this study, it was tried to find a solution for the problem of this kind of photocatalyst by utilizing transition metal, which can show electronic transition with $TiO_2$ in the visible light area. Photocatalyst was prepared, which can have photocatalytic activity in the wide wavelength range, not only ultraviolet region but also visible light area and prevent the combination of electron and hole hindering the photoreaction. For this purpose, by using the ion exchange method, $TiO_2$ precursor and transition metal precursor were dipped into H typed strong acid ion-exchange resin. And two kind photocatalysts (Ti-M-SCM) in which transition metal and titanium dioxide coexist through the carbonization/activation process was prepared. Moreover, photolytic reaction under the wavelength 254 nm and 365 nm was performed for humic acid (HA) in the continuous reactor in order to estimate the efficiency of produced Ti-M-SCM.