• Railway Journal
• /
• v.12 no.5
• /
• pp.20-24
• /
• 2009

• Proceedings of the KSR Conference
• /
• 2006.05b
• /
• pp.1108-1111
• /
• 2006

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1499-1502
• /
• 2003

This paper describes the result of carbody and vibration test for freight car. The purpose of the test is to evaluate an safety which carbody structure shall be considered fully sufficient rigidity so as to load a freight car under maximum load and operating condition on line track. The test carbody is constructed by RS korea co., LTD. in accordance with KNR specfication. The test cases of the carbody is tested the vertical load and compressive load to verify the strength and stillness. The vibration test is tested for analysis and evaluation of vibration, to allow for the fact that mechanical vibration in railway vehicles have specific characteristics.

• Journal of the Korean Society for Railway
• /
• v.4 no.3
• /
• pp.116-122
• /
• 2001

As freight traffic becomes heavier, the high speed of existing freight cars is essential, instead of the construction of a new railway. The high speed can be achieved by the modifications of freight bogie design. In this paper, an analytical model of freight bogie is developed to decide the critical speed. The dynamic responses of the analytical model are compared with the experimental data from a running test of freight bogie and showed good agreements between them. The analytical model is used to find the design of freight bogie. The parameter studies show that the reduction of wheelset mass ratio and the increase of the axle distance of freight bogie can increase the critical speed, but the primary lateral stiffness has little effects on the critical speed. And this study also shows that smaller wheel conicity deteriorates the running safety of freight car, which means that the overhauling of the wheel of freight bogie should be done regularly.

• Journal of the Korean Society of Food Culture
• /
• v.4 no.3
• /
• pp.221-227
• /
• 1989

The introduction of six kinds of teas in Chosun dynasty and tea-making in domestic were investigated. The results were certified as follows. 1. Jasmine tea, blue tea, black tea which are scented tea were introduced from China, red tea was introduced from Japan. 2. Among them, scented tea, yellow tea, black tea were also produced in domestic.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.194-201
• /
• 2002

In this study is presented a numerical method which assesses running safety of the freight car loading with loom CWR and structural safety of conventional railway track and fastening when passing over sharp curves and steel girder bridges. Optimal speed of the freight car is suggested based on the numerical reviews of the safety against derailment of the freight car and structural safety of track and fastening at vulnerable points of the conventional line.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.4
• /
• pp.373-380
• /
• 2010

An interest is increased of environment and energy so, importance on railroad high energy efficiency is magnified. And after Gyeong-bu High speed rail is completed, share rate freight transportation of railroad is expected to be gradually increased due to expand investment for railroad and operate mainly freight transportation on convention line. Therefore a research on DMT freight cars is necessary under like this situation. In paper, we developed analysis model for DMT freight car and DMT freight was analyzed numerically using VI-Rail in each condition of railway having different curve and carried out vibration analysis on curving using developed analysis model. And we carried out test on driving stability follow changing curve radius then measure against UIC code 518.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.18 no.1
• /
• pp.34-39
• /
• 1989

During the preparation of Ssang Wha tea it was observed that the highest yield was obtained when it was extracted with 50% ethanol, of which guantity was added 10 times more then that of Sample. The most effective extraction temperature and time was $90^{\circ}C$ and 8hours on the water bath, which was resulted in saving of production cost. From the HPLC Analysis, it was also observed that product extracted with 50% ethanol give higher yield than that of exfrac ted with water.

• Journal of the Korean Society for Railway
• /
• v.6 no.3
• /
• pp.149-155
• /
• 2003

The development of railway vehicles involves the proper selection of design parameters not only to achieve high speed but also to reduce the vibration of the train. In this study an analytical model of a freight car is developed to find the critical speed. The freight car can generate the snake motion of the lateral and yawing motion of the car body, the bogie, and the wheelset. Numerical analysis for the nonlinear equation motions with 17 degrees of freedom showed the running stability and critical speed due to the snake motion. Also, the vibration modes of the freight car was calculated using ADAMS/RAIL, which showed that the critical speed have the yawing modes of the car body and the bogie. Finally this paper shows that the snake motion of the vehicle can be controlled with the modifications of the design parameters.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.1005-1006
• /
• 2008