• Journal of Korean Society of Transportation
• /
• v.28 no.6
• /
• pp.17-24
• /
• 2010

As various social problems occur due to increasing traffic accidents, the government has setup and executed strong safety policies. As a result, the number of traffic accidents and the death toll have been decreasing in recent years. However, the setup and execution of the various policies for reducing traffic accidents cost much, so it is necessary to evaluate the cost-effectiveness of each policy. In the present study, enforcement by means of an unmanned over-speed enforcement system, the enforcement effect of which was proven good compared to the cost required for traffic enforcement, is compared with enforcement by policemen. As a result of the comparison, the average speed was 82.66 km/h before the use of unmanned systems and policemen; the average speed with manned enforcement was 70.57 km/h; and the average speed with unmanned systems was 67.85 km/h. The speed limit violation rate was 65% before the use of unmanned systems and policemen; 32% with manned enforcement; and 15% with unmanned systems. Considering the kinds of vehicles, the average speed and violation rate were highest among private cars, then vans, and then trucks.. Considering lanes. The accident rate was estimated based on the above results, and the input cost-to-advantage was estimated. The annual cost-to-advantage was estimated by comparing the above estimated values with the conditions before the unmanned over-speed enforcement system. Subsequently, the enforcement by policemen showed a negative advantage of 76,130,590 won, and the enforcement by the unmanned system showed a positive advantage of 38,577,670 won.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.3
• /
• pp.409-415
• /
• 2022

The length of the acceleration lane in the area of entrance terminals is calculated based on 13 PS/ton horsepower of a cargo truck in Korea, so it is generally overestimated compared with the capacity of most vehicles traveling on an entrance ramp. Most drivers have, therefore, an indiscreet tendency to enter the main lane in all sections of an acceleration lane, which affects the traffic flow of the main lane. Because of this tendency, measures are required to minimize the impact on traffic flow of the main lane. The operating speed, rate of entrance, and traffic volume for each vehicle were investigated at the entrance terminals of the interchanges (ICs) of Yangji IC, Suseok IC, Yongin IC, and Osan IC, and the level of improvement in traffic flow was analyzed via VISSIM simulation. From the VISSIM simulation analysis, 74.0 % of the total vehicles traveled over the specified speed from the nose point where drivers would be able to recognize the traffic condition of the main carriageway, or the point at which there is a simplification of the curve section. In addition, 88.6 % of the vehicles entered the main carriageway up to 0.8 points compared with the entire length of the acceleration lane. It was subsequently found that an improvement of average speed in the main carriageway and at the entrance ramp can be achieved from 60.1 km/h to 68.5 km/h by intentionally limiting the entrance point onto the main carriageway up to 0.265 points of the entrance ramp.

• Journal of Korean Society of Transportation
• /
• v.17 no.2
• /
• pp.149-162
• /
• 1999

One of the most important steps of the design, capacity and operation analysis stapes in the two-lane two way highways is the effect of heavy vehicle to traffic flow quality. This heavy vehicle's effect on traffic flow can be represented as PCE, which is the number of passenger cars that are displaced by a single heavy vehicle of a particular type under prevailing roadway, traffic, and control conditions. In this paper, we focus on the heavy vehicles effect on volume, speed, delay, and the maneuver of freedom which are major MOE's in traffic operation analysis and PCE criterion which should be measurable, determinable and able to reflect the traffic flow characteristics. Therefore, the objective of the paper is to determine the PCE criterion and to develop a new PCE determination method. In this study, delay is adopted as PCE criterion and, for calculation of delay, the highway is divided into the passing zone and the no-passing zone. PCE is determined by comparing the delay due to total traffic flow interaction with the delay due to a single heavy vehicle, Also, this paper proposes a new method to determine the average PCE on the highway that has the passing zones and no-passing zones.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.75-82
• /
• 2007

This study was performed to investigate impacts of truck lane restrictions on multilane highways on traffic flow variables such as average speed, the frequency of lane changes, and change in traffic volume and also to verify whether or not different lane restriction scenarios were proper. Two types of hypothetical highway networks and OD demands were developed for traffic simulation models in order to conduct the experimental study. Three types of scenarios were also developed according to the number of restricted lanes for trucks. The PARAMICS microscopic traffic simulation software package was used as the primary analytical tool. Statistical analysis was conducted with simulation outputs. Results showed that truck lane restrictions may lead to positive impacts on traffic flow on multilane highways. In addition, this study demonstrated that the number of restricted lanes can be very an important factor to lead successful implementation of truck lane restrictions.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.107-117
• /
• 2020

With the recent development of autonomous vehicles, various sensors installed in vehicles have become common, and big data generated from those sensors is increasingly being used in the transportation field. In this study, we proposed a grid index method to efficiently process real-time vehicle sensing big data and public data such as road weather. The applicability and effect of the proposed grid space division method and grid ID generation method were analyzed. We created virtual data based on DTG data and mapped to the road link based on coordinates. As a result of analyzing the data processing speed in grid index method, the data processing performance improved by more than 2,400 times compared to the existing link unit processing method. In addition, in order to analyze the efficiency of the proposed technology, the virtually generated data was mapped and visualized.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6D
• /
• pp.749-754
• /
• 2011

It is common that basic unit and model of fuel consumption have been used to evaluate effectiveness analysis of transportation infrastructure investment programs. However they could not reflect vehicle characteristics such as loading capacity and types of heavy vehicles. For these reasons, this study reviews convention fuel consumption model which is widely used and conducts a field experiment for 5 classes of heavy vehicles. To develop the fuel consumption quadratic model the field data are used and we develop each model by classes, and then compare with convention fuel consumption model. As a result, between convention and suggested model, there are considerable differences, which have a similar pattern between an 11-ton cargo of convention model and a 25-ton cargo type dump truck of the suggested model. Likewise we identify that there is an approximately 26% gap between convention model result and the result which is calculated a weighted average by registered number of heavy vehicles based on 5 types of fuel consumption model suggested in this study. This result implies that convention fuel assumption model has a realistic limitation.

• Journal of Korean Society of Transportation
• /
• v.15 no.3
• /
• pp.75-92
• /
• 1997

추월가능성을 판단하기 위해서 앞을 바라볼 수 있어야 하는 거리를 추월시거라 한다. 적절한 추원시거의 확보는 2차선 도로의 효율성과 운전자의 안전성 제고 및 도로설계시 매우 중요하다. 이러한 목적을 위하여 추월시거를 산정할 수 있는 여러 모형이 개발되었으나, 실제 교통상황을 반영하기에 많은 문제점을 안고 있음이 지적되고 있다. 따라서 본 논문은 기존 모형들의 이론적 배경을 고찰하고, 각 모형의 단점과 한계를 파악하여, 운전자의 실제 추월형태를 고려한 새로운 추월시거산정모형을 개발하는데 주안점을 두고 있다. 본 논문에서 개발한 PASS모형은 현재 미국에서 도로설계시 기준으로 사용되고 있는 AASHTO모형을 보완하여 구축하였다. 기존의 모형들은 서로 다른 조건을 가정하여 개발되었기 때문에 각 모형들의 추월시거 산정값을 비교분석하는데 어려움이 있다. 하지만 PASS모형은 운전자의 반응시간, 차량의 길이, 차량의 가속능력 등 실제 추월시거 산정시 반드시 고려해야 할 중요한 요소들을 특성치로 반영할 수 있게 함으로써 다양한 추월 상황과 현실적인 교통상황을 폭넓게 수용할 수 있는 장점을 갖고 있다. 본 논문에서는 새로 개발한 P SS모형을 이용하여 얻은 결과와 기존의 AASHTO모형, MUTCD모형, Glennon모형을 통해 얻은 결과를 비교하였으며, PASS모형에 우리나라 현실에 적합한 특성치를 적용하여 2차로 도로의 추월시거를 산정하였다. 이 결과 현재 우리나라 도로용량편람에서 제시하고 있는 추월기능구간 기준인 450m가 설계속도가 낮은 일반국도에는 타당함을 확인할수 있었다. 그러나, 설계속도가 높은 화물타의 운행빈도가 높은 고속국도의 경우, 재검토가 필요할 것으로 판단된다.기존의 광유계 윤활제에 비하여 대단히 고가하는 문제점을 갖고 있다. 그러나 윤활 마찰면의 다양화와 가혹한 사용조건은 자성유체 윤활제의 연구개발 필요성을 크게 증대시키고 있다.xed Effects Model)을 결정하고, 각각에 해당하는 통계모형을 구축하였다. 이 결과 (1) 업종 및 기업규모별로 그룹간에 유의한 특성이 발견되었으며, (2) R&D 및 광고투자는 기업의 시장성과를 설명하는 중요한 변수이나, (3) R&D 투자의 경우는 광고에 비해 불확실성이 존재하는 것으로 나타났고, (4) 수리모형에서 도출된 한계원리가 통계모형에서도 유효한 것으로 드러났다.등을 토대로 한 10대 산업을 육성하기 위하여 과학기술부는 기술수요조사를 바탕으로 49개 주요기술을 도출하여, 과학기술 일류 국가 실현, 국민소득 2만불 달성이라는 국가적 슬로건을 내걸고 “차세대 성장동력” 창출을 위한 범정부차원의 기획과 연구비의 집중투자를 추진하고 있다.달성하기 위해서는 종합류류 전산망의 시급한 구축과 함께 화물차의 적재율을 높이고 공차율을 낮출 수 있는 운송체계의 수립이 필요한 것으로 판단된다. 그라나 이러한 화물전용차선의 효과는 단기적인 치유책일 수밖에 없기 때문에 물류유통 시설의 확충을 위한 사회간접자본의 구축을 서둘러 시행하여야 할 것이다.으로 처리한 Machine oil, Phenthoate EC 및 Trichlorfon WP는 비교적 약효가 낮았다.>$^{\circ}$E/$\leq$30$^{\circ}$NW 단열군이 연구지역 내에서 지하수 유동성이 가장 높은 단열군으로 추정된다. 이러한 사실은 3개 시추공을 대상으로 실시한 시추공 내 물리검층과

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.95-107
• /
• 2016

The axle weight of a vehicle in motion can be measured with a low-speed or high-speed weigh-in-motion (WIM). However, the axial load dynamically change depending on the vehicle's characteristics-such as the chassis or axle structure-or the characteristics of the driving environment such as road flatness. The changes in dynamic load lead to differences between the vehicle's weight measured at rest and the vehicle's weight measured in motion. For this Study, an experiment was conducted with an instrumented vehicle to analyze the range of errors caused by uncontrollable environmental factors by identifying the characteristics of the dynamic load changes of a vehicle in motion, and determine the appropriate scale for the accuracy evaluation of a high-speed WIM, as a preparatory research for the introduction of unmanned overweight enforcement systems in the future. The key findings from the experiment are summarized as follows. First, The gross weight of the tested vehicle changed by approximately 1% at low velocities and approximately by 4% at high velocities, and the vehicle's axle weight changed by approximately 1-3%, at low velocities and by 2-9% at high velocities. A single axle showed larger weight changes than individual axles in a group. Secondly, The vehicle's gross weight and the axle weight on the impact section were up to eight times and three-to-twelve times higher, respectively, than its gross weight and the axle weight on the flat section. The vibration frequency of the vehicle's dynamic load was measured at between 2.4 and 5.8Hz, and found to return to the normal amplitude after moving approximately 30 meters.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.349-360
• /
• 2024

The purpose of this study is to analyze the performance of the road network according to the penetration rate of autonomous vehicles (AV) of Level 4 or higher and the change in traffic volume. First, prior studies related to vehicle control variables of AV were reviewed, and future traffic demand in 2040, which is predicted to have a 50 % market share of AVs, was reflected in the simulation analysis. In addition, the change in traffic flow of continuous and intermittent flows was analyzed by increasing the AV market penetration rate and traffic volume of passenger cars, trucks, and buses by 25 % step by step from 0 to 100 %. As a result of the analysis, it was confirmed that the travel time increased as the traffic increased, and the pattern of decreasing the travel time due to the increase in the share of AVs, that is, the development of technology, can also be confirmed. Furthermore, it was also confirmed that the traffic speed showed a trend of increasing as the share of AVs increased. In this study, it was confirmed that the law of diminishing marginal rate of substitution (MRS) was satisfied by calculating the MRS according to the combination of traffic volume and speed while increasing the market penetration rate of AVs. Furthermore, it was confirmed that the convexity of the indifference curve was also satisfied in both intermittent and continuous traffic flow environments.

• Journal of Cadastre & Land InformatiX
• /
• v.47 no.2
• /
• pp.233-254
• /
• 2017

The purpose of this study is to analyze the main factors influencing the severity of traffic accidents and to visualize spatiotemporal characteristics of traffic accidents in Seoul. To do this, we collected the traffic accident data that occurred in Seoul for four years from 2012 to 2015, and classified as slight, serious, and death traffic accidents according to the severity of traffic accidents. The analysis of spatiotemporal characteristics of traffic accidents was performed by kernel density analysis, hotspot analysis, space time cube analysis, and Emerging HotSpot Analysis. The factors affecting the severity of traffic accidents were analyzed using decision tree model. The results show that traffic accidents in Seoul are more frequent in suburbs than in central areas. Especially, traffic accidents concentrated in some commercial and entertainment areas in Seocho and Gangnam, and the traffic accidents were more and more intense over time. In the case of death traffic accidents, there were statistically significant hotspot areas in Yeongdeungpo-gu, Guro-gu, Jongno-gu, Jung-gu and Seongbuk. However, hotspots of death traffic accidents by time zone resulted in different patterns. In terms of traffic accident severity, the type of accident is the most important factor. The type of the road, the type of the vehicle, the time of the traffic accident, and the type of the violation of the regulations were ranked in order of importance. Regarding decision rules that cause serious traffic accidents, in case of van or truck, there is a high probability that a serious traffic accident will occur at a place where the width of the road is wide and the vehicle speed is high. In case of bicycle, car, motorcycle or the others there is a high probability that a serious traffic accident will occur under the same circumstances in the dawn time.