• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.636-639
• /
• 2003

It is difficult to machine below 10 micrometers by conventional machining methods, such as micro-EDM. However, ultra micro machining using focused ion beam(FIB) is able to machine to 50 nanometers. In addition, 3 dimensional structures can be made by a combination of FIB and CVD to the level of 10 nanometers. Die ＆ moulds techniques are better than one-to-one machining techniques in the mass production of ultra size structures, in regards to production costs. In this case, the machining precision of die ＆ moulds affects produced parts. Also, it is advantageous to machine die ＆ moulds to the 10 micrometer level by FIB technique rather than other techniques. In this paper, the grooving characteristics for die ＆ mould materials by FIB were carried out experimentally in order to compare the machining characteristics of FIB with conventional machining methods. The results showed that the machining parameters and the scanning path of FIB affects the precision. The machined width and depth of the groove varied depending on the required depth due to the redeposition of the sputtered ion material accumulating on both the bottom and the side of the wall.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.36-36
• /
• 1999

한국중공업(주)에서 수행한 KSTAR 진공용기 시작품 제작이 완성됨에 따라 제작과 관련된 종합기술을 분석하여 보았다. KSTAR 진공용기 시작품(그림1)은 전체의 1/4섹터인 90도 부분으로서 NBI(Neutral Beam Injection) 포트를 포함하는 45도 섹터와 축소포트(Reduced Port)를 포함하는 45도 섹터를 각각 먼저 제작한 후 두 부분을 용접하여 최종 시작품을 완성하였다. 용접은 SMAW법과 GTAW법 등 두가지 방법을 사용하였으며, 초기 용접시는 용접 면적이 작기 때문에 GTAW법을 이용하였고, 마무리 용접과 같이 용접 면적이 넓고 거친 부분에는 SMAW법을 이용하여 용접하였다. 모든 용접이 완전통과 용접이기 때문에 구조적 안전 면에서 좋으나, 진공측면에서는 다소 미흡한 점이 있다. 시작품은 상하 대칭구조로서 원통부분, 원형부분, 원추부분, 너클부분 (그림2) 등으로 나뉘어 지며 이중 원형품은 금형을 이용하여 성형하였고, 나머지 부분은 굽힘가공 후 절단적업을 하였다. 진공용기 조립은 안쪽과 바깥쪽 내벽부터 용접한 후 폴로이달 리브를 용접하고 외벽을 용접한다. 수평포트와 수직포트를 위해 스터브를 용접한 후 미리 용접해둔 NBI 포트 및 축소포트를 부착시켰다. 용접부위의 누설시험을 위한 방법으로, 용접주위 표면에서 개구하고 있는 홈에 적색 침투액을 침투시켜 침투 후 이 액을 홈의 개구로부터 빨아 내어 용접부위 표면상태에서 실제의 홈의 폭보다 확대한 홈의 지시모양으로 나타내게 하여 누설여부를 알기 쉽게 하는 액체 침투 탐상법을 적용하였다. 지시모양의 크기가 5mm 이상인 부분에 대해서는 재용접을 하였다. 누설 시험으로 초음파 탐상시험이 본제품 제작시 수행되어야 한다. 완성된 시작품에 대해 3군데의 위치에서 각각의 부분들이 용접되기 전과 후에 치수를 각각 측정하여 비교하였다. 또한 포트들에 대해서도 용접 전후 치수를 각각 측정하였다. 이러한 측정은 줄자를 사용하여 측정하였으므로 차 후 3차원 정밀 측정이 수반되어야 한다. 이상과 같이 시작품 제작을 통하여 문제점을 파악하고 개선책을 마련함으로서 향 후 KSTASR 진공용기 본 제품 제작할 때 반영코자 한다.

• Journal of Food Hygiene and Safety
• /
• v.36 no.3
• /
• pp.264-270
• /
• 2021

In this study we investigated the elution level of lead (Pb), cadmium (Cd), arsenic (As), zinc (Zn), nickel (Ni), antimony (Sb), germanium (Ge), aluminum (Al) and hexavalent chromium (Cr⁶⁺) from 69 home-cooking utensils into a food stimulants. The results of migration testing according to the Korea standards and specifications for utensils, containers and packages showed values the allowable migrantion limits. Al was detected in all 7 utensil materials with the average concentration ranging from 0.002-5.989 mg/L. According to the migration conditions for (180℃, 30 min), the average concentration of Al in paper was 7.2 times higher than 25℃, 10 min (P<0.05). The results of migration testing at 180℃, 30 min were also below the allowable migrantion limits. When comparing with the provisional tolerable weekly intake (PTWI) of Al, the estimated weekly intakes (EWI) accounted for 0.000-0.045% for Al.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.177-184
• /
• 2001

C3M(chemical mechanical micro machining) is applied for diminishing the size of burr and fabricating the massless patterning for aluminium wafer(thickness of 1${\mu}m$). It is difficult to perform the micro size machining with the radically increased shear stress. While the miniaturization and function-orientation of parts has been needed in the many field such as electronics, optics and medicine. etc., it is not enough to satisfy the industry needs in the machining technology. In this paper feasibility test of diminishing burr and fabricating maskless pattern was experimented and analyzed. In the experiment oxide layer was farmed on the aluminium with chemical reaction by ${HNO_3}$(10wt%), then the surface was grooved with tungsten carbide tool for the different condition such as the load and fred rate. The result was compared with the conventional machining to show the improvement of C3M with SEM for burr diminish and XPS for atomic existence, AFM for more precise image.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.417-418
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.75-79
• /
• 1995

A cutting experiment using diamond tool was performed to make the die cabity which is composed of micro groove with mirror surface. Fine cutting depth was generated by the elastic recovery of the modified tool holder on the conventional M/C. Surface roughness and profile were investigated with cutting speed and depth and through the low cutting speed of 10mm/min, Rmax 0.005 .mu. m or less of machined surface could be achieved.

• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.16-23
• /
• 1996

용접변수는 재현성을 보장하기 위하여 명시되어져야 할 모든 변수라고 정의 되어질 수 있다. 이러한 용접변수는 이음 설계, 용접부 청소, 홈가공, 예열, 후열처 리, 용접법 변수(예, 용접속도, 전압, 잔류) 등이다. 이러한 용접 변수는 용접절차서 (welding procedure apecification)에 그 내용과 측정값을 기술하도록 되어 있다. 본고에서는 좁은 의미에서 용접변수인 용접전류, 전압, 용접속도, 용접부의 온도 측정 방법을 설명하고 그 활용방법에 대하여 기술하고자 한다. 이러한 용접변수는 컴퓨터 에 접속하여 측정이 이루어 지도록 하여 측정자료의 평가, 기록 및 공정제어에 이용 될 수 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.623-624
• /
• 2005

Micro injection molding is a branch of micro system technology and has been under development for the mass manufacture of micro parts. Enhanced technological products like micro optical devices are entering the market. This paper presents fundamental research on the injection molding technique in micro fabrication. In order to successful manufacturing of micro plastic parts, it is necessary to research for development of micro-injection machine, machining of micro mold, decision of optimum injection conditions and the research for polymer material. Therefore in this study, in order to machining of micro mold, a mold core with microscopic V-shaped groove was tooled by ultra-precise tooling machine. The transcription experiments with a polymer, PMMA resin on the surface of core with Ni plating were carried out and surface profile of injected parts was measured with AFM.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.918-921
• /
• 2000

Micro-machining, one of the non-traditional machining techniques, can achieve a wanted shape of the surface using metal dissolution with electrochemical reaction and can be applied to the metal such as high tension, heat resistance and hardened steel. The workpiece dissolves when it is positioned close to the tool electrode in electrolyte and the current is applied. Traditional machining has been used in the industries such as cutting, deburring, drilling and shaping. The aim of this work is to develop Micro-machining techniques for micro shape by establishing appropriate machining parameters of micro-machining

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1643-1653
• /
• 1994

To facilitate the manufacturing of dull using CNC grinding machine, the simulation of helical groove machining with given wheel profile and setting condition is necessary. Considering the wheel as a collection of thin disks, the flute configuration is predicted in a cross section perpendicular to the axis and the grinding wheel profile is also predicted to machine the desired helical groove with given setting conditions. Two programs for these processes are developed. Using programs interactively, the helical groove machining process can be predicted more accurately. By clarifying the geometrical relation between the shape of cutting edge and the flute configuration in the cross section which is perpendicular to drill axis, it becomes possible to predict the necessary cross sectional shape of wheel for desired drill cutting edge shape. Some factors for the software are considered concerning prediction of accuracy and computing time.