• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1705-1708
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner grooved tube. This bending process make the U shape tube by Hair Pin Bending machine. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.977-980
• /
• 1997

Ultraprecision machining process and MEMS technology have been taken more and more important position in machining of micro parts such as PDP and IT components, as the application field of micro parts increases. A micro machining center is very effective equipment for the fabrication of micro parts, because of its benefits such as lower power consumption, high precision and lower machining cost. Therefore, we study the possibility of application to the micro machining of barrier ribs used in PDP and also analyse the machining characteristics. The fabricated barrier rib has 30~$200\mu\textrm{m}$ pitch and was made by the flat endmill with the diameter of 0.2mm, 40, 000rpm condition.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.334-339
• /
• 2004

Ultraprecision machining and MEMS technology have been taken more and more important position in machining of microparts. Micro endmilling is one of the prominent technology that has wide spectrum of application field ranging from macro parts to micro products. Also, the method of micro-grooving using micro endmilling is used widely owing to many merit, but has problems of precision and quality of products due to tool wear and tool fracture. This investigation deals with state monitoring using acoustic emission(AE) signal in the micro-grooving. Characteristic evaluation of AE raw signal, AE hit and frequency analysis for state monitoring is also presented in the paper.

• 한국정밀공학회지
• /
• 제16권4호통권97호
• /
• pp.220-228
• /
• 1999

The machining accuracy has been improved with the development of NC machine tools and cutting tools. However, it is difficult to obtain a high degree of accuracy when machining deep pocket with long end mill, since machining accuracy is mainly dependant on the stiffness of the cutting tool. To improve surface accuracy in machining deep pocket using end mill, the performance by down cut and up cut is compared theoretically and experimentally. To verify usefulness of up milling, various experiments were carried out. As a result, it is found that up milling produce more accurate surface than down milling in machining deep pocket. For effective application of up milling, various values in helix angle, number of teeth, radial depth of cut and axial depth of cut are applied in experiment.

• 한국정밀공학회지
• /
• 제15권3호
• /
• pp.141-149
• /
• 1998

Diamond shaping is one of the machining strategies to make the optical micro-groove molds, and it is especially useful when the component is an assembly of the linear micro-groove array. A mirrorlike surface and an arbitrary crose-sectional curve can be easily made by the diamond tool. However, the cutting speed of shaping is relatively lower than that of the other cutting methods, and there exist an unstable cutting conditions that generate the chatter. This study is focused on the modeling of the simplified self-induced chatter of the diamond shaping, and the machinabilities of three materials are compared by cutting experiments. From the chatter model and experiments, it is found that the unstable cutting conditions exist when the depth of cut is low and cutting speed is high. It is also found that the brass is relatively good material in micro shaping than copper or aluminium from the cutting experiments.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.636-641
• /
• 2009

Recently, expansion of micro-technology parts requires micro-precision machining technology. Micro-groove machining is important to fabricate micro-grating lens and many micro-parts such as microscope lens, fluidic graphite channel etc. Conventional groove fabrication methods such as etching and lithography have some problems in efficiency and surface integrity. But, mechanical micromachining methods using single crystal diamond tools can reduce these problems in chemical process. For this reason, microfabrication methods are expected to be very efficient, and widely studied. This study deals with machinability in micro-precision V-grooves machining of nickel plated layer using non-rotational single crystal diamond tool and 3-axis micro stages. Micro V-groove shape, chip formation and tool wear were investigated for the analysis of machinability of Ni plated layer.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.164-174
• /
• 1996

As tools for machining precision componants, end mills and ball end mills are widely used. For the end mills have longer cylindrical shape comparing dianeter, they are liable to deflect when machining and induce geometrical error and deterioration of surface roughness. To improve the stiffness and the sharpness of the cutting edge of end mill, a software for manufacturing end mills are developed. The program predicts the result of helical flute grinding and the configuration of cuting edge which is located in cylindrical surface. Furthermore to facilitate the manufacturing end mills using CNC grinding machine, the setting condition which satisfy the geometrical requirements like tool rake angle and stiffness are obtained.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.56-63
• /
• 2012

본 연구에서는 가공된 오스테나이트계 STS 316L ASME 표준 교정시험편을 이용하여 튜브 두께 감소율과 잔존두께에 대한 와전류 신호와 IRIS 신호특성을 비교하여 리보일러 튜브의 현장 적용성을 평가하였다. 그 결과 두께감소율의 경우 와전류탐상검사는 $20%{\times}4$ 평저공, 10% 외면 그루브, IRIS는 80%홈, 10%외면 그루브에서 ${\pm}15%$ 이상의 편차가 발생하였다. 잔존두께의 경우 와전류탐상은 측정치가 모두 허용범위를 만족하였으나, IRIS는 80% 인공홈에서 ${\pm}15%$ 이상의 편차가 발생하였다. 따라서 와전류탐상검사 후 의사지시에 대한 해석, 두께감소율 측정을 위해 IRIS를 수행한다면 신뢰성이 향상될 것으로 판단된다.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1229-1235
• /
• 2011

신뢰성이 가장 우수한 프레팅 피로손상 파라미터를 찾아내기 위해 알루미늄 합금 A7075-T6 을 대상으로 피로시험을 수행하였다. 시편 표면에 홈을 가공하여 패드 접촉압력에 따라 패드-시편 접촉면에서 프레팅 피로균열이 발생하거나 또는 홈에서 일반 피로균열이 발생할 수 있게 하였다. 광학현미경을 이용하여 균열의 발생위치와 방향을 측정하고, 문헌에서 가장 많이 사용되는 프레팅 피로손상 파라미터들의 신뢰성을 평가하였다. 파라미터 값과 최대손상평면 방향을 산출하는데 필요한 응력과 변형률 자료는 유한요소해석으로 산출하였다. 전단모드 피로파손을 가정하는 Fatemi-Socie 파라 미터와 McDiarmid 파라미터가 가장 신뢰성이 높은 것으로 판명되었다.

• 서비스연구
• /
• 제4권1호
• /
• pp.49-59
• /
• 2014

상황인식 기술은 유비쿼터스(스마트) 환경에서 지난 수년간 중요한 이슈로 떠오르고 있으며, 현재도 연구자들에 의해 많은 연구가 이루어 지고 있다. 상황인식 기술은 물리적인 환경으로부터 다양한 정보를 획득/가공하여 사용자에게 능동적인 서비스와 정보를 제공하는 컴퓨터 시스템이다. 상황인식 시스템은 각종 센서로부터 발생하는 낮은 수준의 상황정보를 높은 수준의 상황정보로 변환하여 사용자에게 원하는 서비스를 제공하는 환경을 만들어 준다. 본 논문에서는 물리적인 스마트 공간에 존재하는 각종 센서로부터 얻어진 하위단계(Low-level)의 Event-driven 센서정보를 온톨로지 기반 상황정보로 모델링 하여 상위단계(High-level) 상황정보로 변환하는 상황정보를 모델링하여 상황인식 시스템을 구현하였다. 또한 변환된 High-level 상황정보는 가상공간에서 ECA(Event, Condition, Action) 룰에 따라 사용자에게 언제 어디서나 사용자가 필요로 하는 능동적이고 지능적인 서비스를 제공하고, 스마트 홈 환경에서 사용자에게 다양한 가사 도우미 로봇 서비스의 구현 사례를 소개 하였다.