• Journal of the Korean Institute of Gas
• /
• v.26 no.3
• /
• pp.45-53
• /
• 2022

In order to improve the emission of diesel engines, natural gas-diesel dual fuel combustion compression ignition engines are in the spotlight. In particular, a reactivity controlled compression ignition (RCCI) combustion strategy is investigated comprehensively due to its possibility to improve both efficiency and emissions. With advanced diesel direct injection timing earlier than TDC, it achieves spontaneous reaction with overall lean mixture from a homogeneous mixture in the entire cylinder area, reducing nitrogen oxides (NOx) and particulate matter (PM) and improving braking heat efficiency at the same time. However, there is a disadvantage in that the amount of incomplete combustion increases in a low load region with a relatively small amount of fuel-air. To solve this, sensitive control according to the diesel injection timing and fuel ratio is required. In this study, experiments were conducted to improve efficiency and exhaust emissions of the natural gas-diesel dual fuel engine at low load, and evaluate combustion stability according to the diesel injection timing at the operation point for power generation. A 6 L-class commercial diesel engine was used for the experiment which was conducted under a 50% load range (~50 kW) at 1,800 rpm. Two injectors with different spray patterns were applied to the experiment, and the fraction of natural gas and diesel injection timing were selected as main parameters. Based on the experimental results, it was confirmed that the brake thermal efficiency increased by up to 1.3%p in the modified injector with the narrow-angle injection added. In addition, the spray pattern of the modified injector was suitable for premixed combustion, increasing operable range in consideration of combustion instability, torque reduction, and emissions level under Tier-V level (0.4 g/kWh for NOx).

• Reproductive and Developmental Biology
• /
• v.28 no.2
• /
• pp.83-87
• /
• 2004

The objective of this study was performed to establish the in vitro culture system of porcine in vitro maturation and in vitro fertilization(IVM/IVF) embryo. These studies was to determine the effects of melatonin, nitric oxide donor(SNP), and the combination effects of SNP and melatonin in porcine IVM/IVF embryos. In routine porcine IVM/IVF procedure, oocytes were cultured for 40∼44h incubation, and the zygotes were cultured for 40∼44h in NCSU 23 medium. Then 2 to 8 cell embryos were removed cumulus cell and were allotted randomly to NCSU 23 containing different concentration of melatonin, SNP and SNP plus melatonin in 5% $O_2$, 5% $CO_2$ and 90% $N_2$ at 38.5$^{\circ}C$. Cell numbers of blastocyst were also counted using double fluorescence stain method. In NCSU 23 medium treated with melatonin 0, 1, 5 and 10 nM, the developmental rate of morula plus blastocysts were 33.3%, 39.1%, 33.3% and 27.9%, respectivly. This result show that the developmental rate of morula and blascytocys treated with 1 nM melatonin was higher than in any other groups(P<0.05). The developmental rates of morula plus blastocysts were 41.9% in 0 uM SNP, 25.6% in 50 uM and 28.4% in 100 uM, respectively. The developmental rate of morula plus blastocysts were decreased treated with SNP in NCSU 23. In combined effects of SNP plus melatonin (0, SNP 50 uM, SNP 50 uM plus melatonin 1 nM, SNP 50 uM plus melatonin 5 nM and SNP 50 uM plus melatonin 10 nM), the developmental rates beyond morula stage of porcine embryos were 31.3%, 34.1%, 39.5%, 29.4% and 39.5%, respectively. The addition of SNP 50 uM plus maltonin 1 nM, developmental rates of blastocyst was higher rate than in any other groups. Cell numbers of blastocyst in NCSU 23 treated with melatonin 0, 1, 5 and 10 nM were 41.0, 42.6, 39.6 and 33.0, respectively. In combined effects of SNP plus melatonin (0, SNP 50 uM, SNP 50 uM plus melatonin 1 nM , SNP 50 uM plus melatonin 5 nM and SNP 50 uM plus melatonin 10 nM), cell numbers of developed blastocyst were 36.3, 34.6, 39.0, 39.9 and 39.0, respectively. These result show that the cell numbers of blastocyst treated with 0, 1 and 5 nM melatonin were higher than in 10 nM group(P<0.05), but cell numbers of blatocyst produced by SNP plus melatonin were not significantly difference in all experimental groups.

• The Korean Journal of Mycology
• /
• v.4 no.1
• /
• pp.31-44
• /
• 1976

The studies were carried out to examine the effects of supplementation of nutritional substances and physical conditions in substrate on the mycelial growth and yield of fresh sporophores of winter mushroom, Flammulina velutipes(Curt. ex Fr.) Sing. and to obtain further informations on the nutritional requirements of the fungus with reference to improvement of substrate through [analysis of chemical composition of the substrates during the cultivation period. The results obtained are summarized as follows: 1. The best yield of fresh sporophores, 84.4 g per 280 g substrate in a bottle, was obtained from the mixture of poplar sawdust 10 and rice bran 3 by volume when Flammulina velutipes was cultivated on the poplar sawdust supplemented by rice bran, wheat bran, cattle manure and various combinations of these materials as nutrient sources. The substrates of poplar sawdust 10 plus rice bran 3 and 2 or wheat bran 3 with a higher yield of fresh sporophores showed a comparatively higher content of total nitrogen. total sugar, and potassium. 2. The mycelial growth of the fungus was compared on the substrates of poplar sawdust supplemented by the several nutrient sources and poplar sawdust alone. The fastest linear growth occurred on substrates of poplar sawdust alone and poplar sawdust plus cattle manure deficient in sugar and nitrogen sources, but mycelial density was more sparse on the substrates. Also, growth in a solution extracted from these substrates was very meager. 3. In the substrates which varied with bulk density and moisture content optimum bulk density and moisture content for mycelial growth was 0.2g/cc and 72% on a dry weight basis, respectively, but the highest yield of fresh sporophores was obtained at the bulk density of 0.3g/cc and moisture content of 67%. 4. By increasing the ratio of rice bran in poplar sawdust the loss of total weight and ash, content at each stage was increased, and during the cultivation period of 75 days, loss of total weight of the substrates at inoculation was 17.8 to 28.8% and ash content increased about 12%. 5. 11 to 14% of the cellulose and 3 to 4% of the lignin content per original substrate were decreased without a great difference depending of the mixing ratio of rice bran. The soluble glucose concentration in the substrates was increased during the same period. 6. In the process of vegetative and reproductive growth of the fungus upon the substrates, the total nitrogen was increased in quantity per dry weight of sample but was reduced in absolute quantity to a minute extent. There is no great changes in content of organic nitrogen including amino acid nitrogen, and hydrolysable ammonium nitrogen during the vegetative growth period, but occurrence of sporophores resulted in a decrease in the nitrogen content of these forms. On the one hand, by an increase of additive amounts of rice bran, nitrogen contents of these forms were higher and the reduction range during the reproductive growth period became wider. 7. Mycelial growth of the fungus was accelerated in various liquid media supplemented with organic nitrogen sources such as peptone and yeast extract in comparison with addition of inorganic nitrogen sources. Furthermore, mycelial growth was mere vigorous in the media with higher content of organic nitrogen sources.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.6
• /
• pp.451-464
• /
• 2014

This study used numerical methods to investigates investigate the exhaust gas recirculation (EGR) effect under the condition of boost pressure condition on a homogeneous charge compression ignition (HCCI) combustion engine using numerical methods. The detailed chemical-kinetic mechanisms and thermodynamic parameters for n-heptane, iso-octane, and PRF50 from the Lawrence Livermore National Laboratory (LLNL) are were used for this study. The combustion phase affects the efficiency and power. To exclude these effects, this study decided to maintain a 50 burn point (CA50) at 5 CA after top dead center aTDC. The results showed that the EGR increased, but the low temperature heat release (LTHR), negative temperature coefficient (NTC), and high temperature heat release (HTHR) were weakened due by theto effect of the O2 reduction. The combined EGR and boost pressure enhanced the autoignition reactivity, Hhence, the LTHR, NTC, and HTHR were enhanced, and the heat-release rate was increased. also In addition, EGR decraeased the indicated mean effective pressure (IMEP), but the combined EGR and boost pressure increased the IMEP. As a results, combining the ed EGR and boost pressure was effective to at increase increasing the IMEP and maintaining the a low PRR.

• Journal of Plant Biotechnology
• /
• v.39 no.2
• /
• pp.114-120
• /
• 2012

An efficient in vitro propagation was established by using axillary bud explants of roseroot (Rhodiola rosea L.), which has been known as a medicinal plant in East Asia. Among various media tested, MS medium supplemented with 1.0 mg/L BA and 1.0 mg/L $GA_3$ was found to be the best for multiple shoot formation (15 axillary shoots per axillary bud). In addition 1/2MS medium containing 50 g/L sucrose was best for shoot elongation (7.8 cm) and increasing total chlorophyll contents (8.64 mg/g) best. Maximum number of roots (17.7 roots per explant) was observed on the medium without plant growth regulators. Propagated plants were successfully acclimatized to ex vitro conditions, with a survival frequency of 97% after 12 weeks. Most rooted shoots grew well and produced viable seeds when grown in vitro culture conditions. Therefore, R. rosea can be effectively propagated in vitro by the system we developed in this study.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.251-257
• /
• 2012

This work presents an experimental investigation of NOx emissions according to inlet air temperature (550-660 K), stoichiometric air ratio (${\lambda}$, 1.4-2.1), and elevated pressure (2-5 bar) in a High Press Combustor (HPC) equipped with a double cone burner, which was designed by Pusan Clean Coal Center (PC3). The exhaust-gas temperature and NOx emissions were measured at the end of the combustion chamber. The NOx emissions generally decreased as a function of increasing ${\lambda}$. On the other hand, NOx emissions were influenced by ${\lambda}$, inlet air temperature and pressure of the combustion chamber. In particular, when the inlet air temperature increased, the flammability limit was extended to leaner conditions. As a result, a higher adiabatic temperature and lower NOx emissions could be achieved under these operation conditions. The NOx emissions that were governed by thermal NOx were greatly increased under elevated pressures, and slightly increased at sufficiently low fuel concentrations (${\lambda}$ >1.8).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.610-616
• /
• 2020

Recently, the application of a photocatalyst to road structures is being attempted to solve environmental problems caused by fine particulate matter and automobile exhaust. The purpose of this study was to develop a release agent with GST (low-cost, high-performance photocatalyst produced from wastewater sludge). For this, the method of mixing and dispersing GST with the release agent was used first, and the removal performance of nitrogen oxide (NOx) was then checked. The best performance without a precipitation reaction was achieved using a stabilizing agent at 20 % in an outdoor exposure test for four weeks. The NO and NOx removal rate of the specimen demolded by applying the GST release agent developed in this study showed excellent effects of 200 to 400 % compared to the Plain material. To increase the performance of the GST release agent, it is necessary to improve the dispersibility of GST in the release agent and increase the amount of the nano-sized photocatalyst. In addition, the use of GST release agent in road structures and exposed concrete is expected to increase the NOx removal efficiency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.345-350
• /
• 2017

Downsizing is widely applied to diesel engines in order to improve fuel efficiency and reduce exhaust emissions. Engine sizes are becoming smaller but pressure and temperature inside combustion chambers are increasing. Therefore, research for fuel spray under high pressure and temperature conditions is important. A constant volume chamber which simulates high temperature and pressure likely to be found in diesel engines was developed in this study. Pressure and temperature were increased abruptly because of ignition of the pre-mixture in the constant volume chamber. Then pressure and temperature were gradually decreased due to the heat loss through the chamber wall. Fuel spray occurred when temperature and pressure were reached at the target condition. In this experiment, the temperature condition should be exactly defined to understand the relation between fuel evaporation and ambient temperature. A fast response thermocouple was developed and used to measure the temporal and spatial temperature distribution during the combustion process inside the combustion chamber. In the results, the core temperature was slightly higher than the bulk temperature calculated by the gas equation. Ed-note: do you want to say 'ideal gas equation'? This was attributed to the heat transfer loss through the chamber wall. The vertical temperature deviation was higher than the horizontal temperature deviation by 5% which resulted from the buoyancy effect.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.61-67
• /
• 2015

The cooling of hot exhaust gas is an important issue for the construction of combustor test facility. Water spray is an effective method for exhaust gas cooling due to its large latent heat in process of evaporation. In this study, 1-D analysis has been performed based on continuity, energy conservation, and saturated vapor property to understand water spray cooling of combustion gas. In the exhaust duct of combustor test facility, the injected water decreases combustion gas temperature, and evaporates in the combustion gas. However, some of the injected water is collected in the sump due to condensation. The evaporation of water helps combustion gas cooling, but causes pressure increase inside the exhaust duct due to increase of vapor pressure. These phenomena has been analyzed by 1-D modeling in this study. From 1-D analysis, the adequate mass flow rate of water spray to cool combustion gas and to avoid excessive pressure rise inside the exhaust duct has been decided.

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 1979.10a
• /
• pp.244.3-245
• /
• 1979

1. 수율계수 함수의 영향 : 유가 배양에 있어서 수율 계수가 제한 기질 농도의 함수일 경우에 대한 연구를 수행하였다. 사용한 수율 계수 함수는 기질 농도에 대하여 선형 함수였으며 목적함수는 중간 대사 물질의 생산량이었다. 1-가) 수율 계수 함수의 기울기가 음의 값으로 적어짐에 따라 제한 기질의 공급속도가 증가되었다. 1-나) 일반적으로 초기의 얼마 동안은 회분 배양에서와 같이 공급 속도가 거의 없었으며 그후 전환점 이후에 가서야 공급 속도가 증가하였다. 1-다) 전환점 이후에서도 처음에는 대부분의 경우에 공급속도가 음의 값으로 부터 시작하여 증가하기 시작하였다. 1-라) 어떤 경우에는 배양 초기부터 공급 속도가 양의 값으로부터 시작하였으나 곧 감소하였다가 다시 증가하는 비 단조형 변화를 보였다. 1-마) 전환점 이후에서 공급 속도가 증가하는 형태에서도 처음에는 선형 증가를 보이다가 나중에 지수적 증가를 보였다. 1-바) 위와 같은 공급 속도의 변화에 따른 발효조 내의 제한 기질 농도의 변화는 초기에는 가능한 최대치를 유지하다가 전환점 이후에는 갑자기 감소하는 형태를 취하였다. 2. 목적 함수의 영향: 목적 함수가 균체량과 생성 중간 대사물질 량의 선형 결합일 때 대하여 연구하였다. 선형 결합 계수로는 균체량과 생성대사 물질의 상대적인 값어치를 취하였다. 2-가) 허용 최대 균체 농도가 제한되어 있는 상황 하에서 생성 대사 물질의 상대적인 값이 증가 할수록 목적 함수가 증가하였다. 2-나)생성대사 물질의 상대적인 값이 증가할수록 전환점의 위치가 줄어들었다. 2-다) 생성대사 물질 상대적 값의 단위 증가에 대한 목적 함수는 균체량을 감안하지 않은 야마네박사의 결과에 수렴하였다. 2-라) 공급 속도는 상대 값이 커질수록 줄어들었다. 2-마) 균체량의 시간에 대한 곡선은 상대값이 증가할수록 감소하고 전형적인 분기점 형태의 변화를 보였다.변이 뚜렷하여 이로 인한 외임파강내의 염증성병변이 뚜렷이 나타나 있으며 와우관의 특히 기저회전에서의 유모세포의 손실이 심한 것으로 보아 중이염으로 인한 골도의 고음역에서의 손실이 발생함을 알 수 있다.A group), vinclozolin, procymidone, tetradifon cypermethrin, 그리고 fenvalerate(B group)에서는 70% 이상의 회수율을 얻었고, 20%의 ethyl acetate/hexane을 사용하여 분석한 경우는 5%나 10%의 ethyl acetate/hexane을 사용하여 분석했을 때보다 좋은 결과를 나타내어 전체 16종의 농약 중 14종에서 75% 이상의 회수율을 얻었으나, alachlor와 bifenthrin은 매우 낮은 회수율을 보여서 ethyl acetate와 hexane의 혼합용매가 이들 두 농약성분의 분석에는 적합하지 않은 용출 용매임을 알 수 있었다.NO_2의$ 급성 중독증상으로서는 눈, 코를 강하게 자극하고 폐충혈, 폐수종, 기관지염, 폐염 등을 일으킨다. 만성 중독시에는 만성폐섬유와 및 폐수종을 일으킨다. (4) $오존(O_3)$ Ozone은 자동차 배기가스에서 나오는 $NO_2$ gas 및 탄화수소와 작용하여, PAN이라는 자극성 물질을 생성시키는 광학적 Smog의 주요소로 알려져 있다. 자극적인 냄새가 있음으로 불쾌감을 주고 비, 인후점막의 전조감과 두통이 오며 폐기능을 저하시키며 더욱 진행되면 폐충혈, 폐수종 등을 일으킨다 (5) Smog에 의한 건강피해 대표적인 것이 1952.12.5~12.8까지 4일간 영국 Lon-don에서 계속된 Smog사건이며, 이 사건으로 말미암아 호흡기질환 사망율이 사건전보다 사건기간 중 혹은 사건후에 5~10배의 증가율을 보였다. 이때 Smog의 주원인은 연료의 불완전 연소에 의한 연기와 이때 발생