• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.4
• /
• pp.76-83
• /
• 1985

Mo2N/Mo double layer which is to be used for gate of the RMOS (refractory metal oxide semiconductor) and interconnection material has been formed by means of low temperature r.f. reactive sputtering in Ar and N2 mixture. The sheet .esistance of 1 000$\AA$Mo2 N/4000$\AA$Mofilm was about 1.20-1.28 ohms/square, which is about an order of magnitude lower than that of polysilicon film. The workfunction difference naE between MO2N/MO layer and (100) p-Si with 6-9 ohm'cm resistivity obtained from C-V plots was about -0.30ev, and the fixed charge density Qss/q in the oxide was about 2. Ix1011/cm2. To evaluate the signal transfer delay time per inverter stage, an integrated ring oscillator circuit consisting of 45-stage inverters was fabricated using the polysilicon gate NMOS process. The signal transfer delay time per inverter stage obtained in this experiment was about 0.8 nsec

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.6
• /
• pp.418-423
• /
• 2012

In order to develop the end use of cylindrical laminated veneer lumber (LVL) such as wooden crafts, the water proof-bonding strength, the resistance to abrasion and the surface hardness by painting the surface of LVL were investigated. The study results were as follows; The water proof-bonding strength through 5 cyclic test by boiling in water immersion and drying were favorable without delamination of glue line. Then the formulation of glue was resorcinol resin (100) to hardener of paraformaldehyde (5) by mixed weight percentage. The resistance to abrasion was relatively higher at cross section than tangential section. When tangential section of LVL was painted by UV protection oil, the resistance to abrasion was improved. In case of an cross section of LVL, the higher surface hardness appeared at larch core than radiata pine LVL. Also, in case of an tangential section of LVL, the higher surface hardness appeared at glue line than veneer side.

• Geotechnical Engineering
• /
• v.4 no.2
• /
• pp.33-44
• /
• 1988

The Taechong Dam completed in 1980 is a composite dam at which a junction was formed partly by butting the core against the end face of the concrete gravity section and partly by the core overlapping the upstream face of the concrete. In order to evaluate the performance of the junction, the interfaces between the concrete dam and core of the embankment dam were well instrumented with total pressure cells and piezometers. A nonlinear incremental finite element analysis simulating its construction behaviour was carried out under plane strain conditions. Material parameters for the core are determined from triaxial tests on the specimens, sampled in the quarry site and compacted to the field dry density at the field moisture content. Material parameters for the filter, transition materials and the rockfill are estimated from literature. When compared with the earth pressures measured at the interfaces, the analytical results show good agreement in the core, however, there are some discrepancy in the shell. A nonlinear model for pore pressure response is used successfully to predict the pore pressures at the interface in the core.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.204-215
• /
• 2011

Flame stability is the one of the main mechanism of laminar lifted flame and flame propagation velocity becomes a yardstick to measure the flame stability. Bilge has presented the flame propagation velocity of the triple flame and the flame stability mechanism related the flame configuration and mixture fraction. However, there was not able to observe all process of flame ignition and extinction for small nozzle diameter. In this paper, we have subdivided the flame configuration and stability mechanism and classified the flame behavior with a nozzle diameter. Also we have subdivided the 'triple flame propagation opened' and the 'triple flame propagation closed' from the triple flame propagation of triple flame criterion.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1067-1073
• /
• 1998

High quality diamond films of the silicon on diamond (SOD) structure are deposited using CO and $H_2$ gas mixture in microwave plasma chemical vapor deposition (CVD), a SOD structure is fabricated using low pressure CVD polysilicon on diamond/ Si(100) substrate. The crystalline structure of the diamond films which composed of { 111} and {100} planes. were changed from octahedral one to cubo-octahedron one as the CO/$H_2$ ratios are increased. The high quality diamond films without amorphous carbon and non-diamond elements were deposited at the CO/$H_2$ flow rate of 0.18. and the main phase of the diamond films shows (111) plane. The diamond/Si(lOO) structure shows that the interface is flat without voids. The measured dielectric constant. leakage current and breakdown field were $5.31\times10^{-9}A/cm^2$ and $9\times{10^7}{\Omega}cm$ respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.28-34
• /
• 2006

In general engineering problems, the purpose of an optimization is to get optimal design variables. It is the same problem to fix the total amount of the design variables and to judge the optimal mixing proportions of the design variables. That is to say, we can recompose the engineering problems in the concepts of the mixture amount experiments. The goal of mixture amount method is to get the response surfaces of varying both the mixing proportion of component and the total amount of the mixture. The solution of the aircraft fuselage optimization problem is obtained by the mixture amount method and genetic algorithm. In this study, it is shown that the mixture amount method can be utilized for the aircraft structural optimization problem. Also, this method in this study can be applied for the optimization problems over 12 design variables which is impossible for D-optimal design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.79-88
• /
• 2006

In the present paper, the swirl flow structure and flame characteristics of turbulent premixed combustion in a model gas turbine combustor are investigated using large eddy simulation(LES). A G-equation flamelet model is employed to simulate the unsteady flame behavior. When inlet swirl number is increased, the distinct flow structures, such as the shapes of corner recirculation and center toroidal recirculation zone, are observed and the flame length is shorted gradually. Also, the phenomena of flashback are identified at strong swirl intensity. In order to get the accurate description of unsteady flame behavior, the predictive ability of the acoustic wave in a combustor is primarily evaluated. It is found that the vortex generated near the edge of step plays an important role in the flame fluctuation. Finally it is examined systematically that the flame and heat release fluctuation are coupled strongly to the vortex shedding generated by swirl flow and acoustic wave propagation from the analysis of flame-vortex interaction.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.1
• /
• pp.24-31
• /
• 2005

Ion shower doping with a main ion source of $P_2H_x$ using a source gas mixture of $PH_3/H_2$ was conducted on excimer-laser-annealed (ELA) poly-Si.The crystallinity of the as-implanted samples was measured using a UV-transmittance. The measured value using UV-transmittance was found to correlate well with the one measured using Raman Spectroscopy. The sheet resistance decreases as the acceleration voltage increases from 1kV to 15kV at the moderate doping conditions. It, however, increases as the acceleration voltage increases under the severe doping conditions. The reduction in carrier concentration due to electron trapping at uncured damage after activation annealing seems to be responsible for the rise in sheet resistance. Three different annealing methods were investigated in terms of dopant-activation and damage-recovery, such as furnace annealing, excimer laser annealing, and rapid thermal annealing, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.8
• /
• pp.27-35
• /
• 2005

Several damages due to large displacement caused by liquefaction have been reported increasingly. Numerical procedures based on effective stress analysis are therefore necessary to predict liquefaction-induced deformation. In this paper, the fully coupled effective stress model called UBCSAND is proposed to simulate pore pressure rise due to earthquake or repeated loadings. The proposed model is a modification of the simple perfect elasto-plactic Mohr-Coulomb model, and can simulate a continuous yielding by mobilizing friction and dilation angles below failure state. Yield function is defined as the ratio of shear stress to mean normal stress. It is radial lines on stress space and has the same shape of Mohr-Columob failure envelope. Plastic hardening is based on an isotropic and kinematic hardening rule. The proposed model always causes plastic deformation during loading and reloading but it predicts elastic unloading. It is verified by capturing direct simple shear tests on loose Fraser River sand.

• Journal of The Korean Association of Information Education
• /
• v.14 no.3
• /
• pp.437-447
• /
• 2010

The purpose of this thesis was to design and develop an effective e-PBL(Problem-Based Learning) for cultivating consciousness of information and communication ethics. The proposed e-PBL is based on PBL which is one of the constructivism teaching-learning theories. Online learning and face-to-face classes were systematically combined for achieving the teaching-learning goals. And the main module for online learning run on Moodle, an open source learning management system. To examine educational effectiveness of the proposed e-PBL, an experimental study was conducted through the education content and method to the subject of two class in the second-grade of university located in OO city. For experiment 60 students(treatment group=30, control group=30) are participated. And they were randomly assigned to one of ten subgroups, comprising of six students, respectively. The results of this study showed that the education using proposed e-PBL is more effective in cultivating consciousness of information and communication ethics and learners responded positively than the education using traditional face-to-face PBL learning method.