• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.104-111
• /
• 2005

Virgin fluororubber(FKM) that is one of the highly-functionalized and expensive special rubber, and recycled FKM that is crushed by high temperature shear-crushing technique from recycled FKM were blended with the various mixing ratio to rubber blends. The cure characteristics and physical properties of these blended rubber compounds were investigated with various contents of recycled FKM and physical properties fur heat and fuels were also measured. Recycled FKM which is prepared by high temperature shear-crushing technique were blended to virgin FKM with the range of $0{\sim}50$ phr. The physical properties indicated that the rubber blend of recycled FKM with 30 phr turned out to be the best compound showing good dispersibility, heat resistance and fuel resistance and inexpensive in price.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.111-120
• /
• 2001

Mechanical properties and their adhesion behavior with zinc- and brass-plated steel cords of natural rubber/acrylonitrile-butadiene blend compounds were investigated as a function of blend ratio. The Mooney viscosity and stress relaxation time were found to be lowered with increasing NBR content. Tensile modulus generally increased with increasing NBR content. Tensile stress at break stayed constant up to about 40 phr and showed minimum at $50{\sim}60 phr$, and thereafter increased with increasing NBR content. Strain at break decreased linearly below 50 phr, and above the level it showed nearly constant value. Based on the abrupt drops in elastic modulus and tan ${\delta}$ peak, the glass transition temperature of NR and NBR were found to be -55 and $-10^{\circ}C$, respectively. In the case of NR/NBR blend compounds, two distinct transition points were observed and each transition position was not affected by NBR level indicating an incompatible nature of NR/NBR blend system. The pullout force and rubber coverage decreased to the level of about 40% to that of pure m compound, when the 50 phr of NR was replaced by NBR. However, the pure NBR compound showed the comparable adhesion performance with NR(${\sim}90%$). The sulfur concentration was found to become lower with the increased NBR content at the adhesion interface based on the Auger spectrometer results, representing a lack of adhesion layer formation, and this was explained for a possible cause of low adhesion performance with adding NBR.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.83-92
• /
• 2005

To develop an automotive fuel hose suitable to the international environmental regulation, FKM rubber materials as an inner material of fuel hole were prepared with different chemical compositions. Measurement of the properties of thermal resistance, oil resistance, fuel resistance, gas permeability including fundamental properties were performed to investigate compatibility for a fuel hose material. Fundamental properties, thermal resistance, oil resistance, fuel resistance and permeability of FKM rubber materials were improved with fluorine content. When the carbon content was 20 phr, FKM compounds with fluorine contents of 66%, 09% and 71% were shown to satisfy the specification oi fuel hose. The gas permeability of NBR and FKM compounds was measured on the mixed fuel oils prepared with isooctane-toluene and gasoline-methanol. FKM rubber materials showed a small difference in penetrated amount of fuel and showed a permeability superior to NBR material. he permeability of FKM rubber materials was not influenced by the contents of fuel oil. Thermal properties of 69% FKM rubber experienced by permeability testing were not variated.

• Elastomers and Composites
• /
• v.28 no.1
• /
• pp.13-21
• /
• 1993

Polyurethane resin was especially mixed with polybutadiene rubbers which had each other different molecular structures and functional groups. Liquid and cure properties were tested experimentally for mixtures. Viscosity of mixtures and drying time were influenced by solubility of thinner and reactivity of rubber. Adhesive strength represented maxium at rubber content $15{\times}22%$ (Wt. % ), and rapidly decreased over 25%. DBTDL(di-n-butyltindilaurate) showed the longest stroage stability.

• Elastomers and Composites
• /
• v.34 no.3
• /
• pp.247-252
• /
• 1999

Rubber related geosynthetics(GS) as reinforcement and water barrier materials were manufactured by thermal bonding method and examined the their performance for applications to civil and environmental engineering fields. The spunbonded polyester nonwoven, fiber glass mat and fabric type geogrid of a high tenacity polyester filament were used as matrix and polyester film, elastomeric bitumen with SBS polymer and asphalt were used as reinforcements to manufacture the rubber related geosynthetics. A fiber glass mat and geogrid matrix GS showed more excellent mechanical properties and nonwoven and elastomeric bitumen matrix showed the more excellent permittivity. Softening points of rubber and asphalt mixture showed no difference and dimensional stability at high temperature, $120^{\circ}C$, represented no significant shrinkage. Resistance to ultraviolet of rubber related geosynthetics showed no visible alteration.

• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.63-72
• /
• 1990

Surface of crystalline silica was sequentially reacted with silane(A 187), liquid rubber(CTBNx8) and vinyl monomer(AA, MMA, 2-HEA, GMA) in existance of amines(TEA, CTMAB, BETAC) or peroxide(BPO). By mixing it with epoxy resin at a ratio 0~36%(volume %) of total component, liquid properties of mixtures was investigated experimentally. i) Coating ratio depended on quantity and sorts of catalyst. ii) Total coating of 2.5~5.8% was attained by using 0.1~2.0% of catalyst. iii) Treated surfaces represented each different features in according to sorts of treatment. iv) Silane/rubber or silane/rubber/vinyl represented lower viscosity and settling than non-treated or silane-treated.

• Journal of Adhesion and Interface
• /
• v.1 no.1
• /
• pp.30-37
• /
• 2000

This study focused on the direct blending of bonding agents (resorcinol, hexamethylenetetramine, NaOH) into rubber compound to simplify the composite manufacturing process. The mechanism of direct blending system was studied by comparing the following two cases. The one is direct blending of bonding agents into rubber compound and then allows the reaction (Case I). The other is mixing of reactant obtained by reaction of bonding agents (Case II). According to the morphology analysis, the Case II showed the clean interfacial area between bonding agents and matrix rubber, while the Case I created the new interphase under proper processing condition. Also, the optimum adhesion strength between SBR and nylon cord could be obtained with bonding agents whose molar ratios of resprcinol/hexamethylenetetramine was 1.2/1 in the recipes.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.8
• /
• pp.125-135
• /
• 2008

Rigid-soft particle mixtures, which consist of sand and rubber, are investigated for the understanding of the stress-deformation and elastic moduli. Specimens are prepared with various size ratio sr between sand and rubber particles, and different volumetric sand fraction sf. Small strain shear waves are measured under $K_o$-loading condition incorporated with the stress-deformation test by using oedometer cell with bender elements. The stress-deformation and small strain shear wave characteristics of rigid-soft particle mixtures show the transition from a rigid particle behavior regime to a soft particle behavior regime under fixed size ratio. A sudden rise of $\Lambda$ factor and the maximum value of the $\zeta$ exponent in $G_{max}=\;{\Lambda}({\sigma}'_{o}/kPa)^{\zeta}$ are observed at $sf\;{\approx}\;0.4{\sim}0.6$ regardless of the size ratio sf. Transition mixture shows high sensitivity to confining stress. The volume fraction for the minimum porosity may depend on the applied stress level in the rigid-soft particle mixtures because the soft rubber particles easily distort under load. In this experimental study, the size ratio and volumetric sand fraction are the important factors which determine the behavior of rigid and soft particle mixtures.

• Elastomers and Composites
• /
• v.30 no.1
• /
• pp.9-19
• /
• 1995

To make filler loaded conducting rubber which has the excellent electronical and physical properties, CR and NBR were mixed with magnetite$(Fe_3O_4)$. From the result of the study, vulcanization characteristics shows the upgrading curve as increase in filler concentration and CR has more torque than NBR. When elongation be higher, modulus comes to decreases. Tear strength gradually decrease after showing of the maximum point when is in the 100phr in all. Resilience is not good to cause the increase in filler concentration. In the electrical properties, conductivity becomes smaller when filler concentration is increased. The increase of voltage makes an conductivity grown, but the changed rate is weak. The influence of temperature hardly changes on increasing temperature. The morphology and the distribution for a conductivity filler through SEM were better, the more filler concentration increase, the shorter the particle interval is.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.283-290
• /
• 2002

Generally polymer mortar and concrete using unsaturated polyester resin has high strengths and good chemical resistance. However it also has high brittleness and because of this reason, it is not used for the purpose that demands high resistance to impact. The purpose of this study is to improve the brittleness of unsaturated polyester mortar(UPE mortar) which could be used for the flooring material with recycled aggregates and UPE. Polyurethane liquid rubber(PU) and recycled aggregates were used to complement the brittleness and to recycle the resources respectively. The characteristics of mortar were investigated according to the molecular weight and substitution rate of PU. As the molecular weight and PU substitution rate were increased, the viscosity was increased, working life became fast and curing shrinkage was reduced. Compressive and flexural strengths were also reduced but tile brittleness was improved. Therefore, it is seemed that the improved WE mortar could be obtained by using polyurethane liquid rubber with the polyol of molecular weight 2000, 3000.