• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.4
• /
• pp.9-17
• /
• 1985

엔진이 고성능화가 되어감에 따라 실린더 헤드 가스켓 재료나 밀봉(sealing) 구조가 계속해서 변 천되어 가고 있고 이는 엔진의 성능향상이 헤드 가스켓에 의해 크게 좌우된다는 것을 알려준다. 그러나 종래에는 헤드와 엔진보아(bore) 간의 밀봉문제가 가스켓만의 문제로 해서 검토하는 경우 가 많았다. 거기에다 검토 되어지는 것도 엔진의 개발 최종단계에서 이기 때문에 엔진을 개선할 수 없어 여러 가지 문제점을 가스켓이 부담하는 경우가 많았다. 그에 의한 무리한 대책은 나중 에 여러 가지 문제를 야기하는 결과를 가져다 준다. 그래서 여기서는 실린더 헤드 가스켓에 관 한 전반적인 내용을 서술하고자 한다.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.5-13
• /
• 1986

내연기관... 1. 헤드가스켓과 엔진구조의 관계 2. 유지(Maintenance)와 헤드볼트 축력관리 3. 헤드가스켓 설계

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.321-325
• /
• 2000

Gasket of vehicle engine maintains airtight between cylinder head and engine block under high temperature and pressure, and plays important role in heat conduction of engine. And the characterization of the nonlinear behavior of metal gasket fer various bead shapes is very important as basic research for estimation of gasket durability. But it is very difficult to analyze the behavior of gasket In real experiment. In this paper, to analysis effects of the bead shape on the nonlinear behavior of cylinder head gasket under uniform pressure, the virtual experiment using the nonlinear finite element method was performed. Results are analyzed with residual deformation and the sealing pressure. With the increase of the height and the width of bead, the residual deformation and the sealing pressure increase. And if the height is very high and the width is very narrow, the wrinkles are occurred in the gasket while working.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.28-38
• /
• 2003

Finite element analysis of cylinder heat/block compound under assembly, thermal and firing condition were performed. FE model including two cylinders with gasket, head bolts, liners and valve seats was used. FE modeling method and boundary conditions were introduced. Stress distribution and deformation of cylinder head and block under each loading condition were presented. Gasket pressure distribution and bore distortion level were predicted. Measured data of bore distortion was compared with the analysis results. The analysis result showed similar trends with the experimental data. High cycle fatigue analysis on the basis of this result has been performed in order to find the critical areas of the engine assembly.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.160-165
• /
• 2007

Exhaust manifold is generally subjected to thermal cycle loadings ; at hot condition, large compressive plastic deformations are generated, and at cold condition, tensile stresses are remained in highly deformed critical zones. These phenomena originate from that thermal expansions of the runners are restricted by inlet flange connected to the cylinder head, because the former is less stiff than the latter and, the temperature of the inlet flange is lower than that of the runners. Therefore, due to the repetitions of thermal deformation, leakage problems could be occur between inlet flange and cylinder head. In this study, we obtained pressure distributions along gasket bead lines from the finite element analysis and compared to the test results. It shows a good agreement between numerical and experimental results.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.77-82
• /
• 2004

This paper describes the improvement of engine cooling system. To improve engine cooling performance, the authors approached in two ways. One is to increase water pump performance, changing of impeller shape and lightening of material were carried out. The second one is cooling efficiency rise, which were investigated with head gasket coolant flow passage optimization with flow visualization technique. The test results show that water pump performance was increased effectively, reduction of pump drive torque, and increase of pump flow-rate and pressure rise. Gasket hole pattern optimization test results represent an optimized head coolant flow which stands cross flow from exhaust to intake port side and small vortex were removed.