• Journal of agriculture & life science
• /
• v.53 no.1
• /
• pp.117-126
• /
• 2019

This paper presents an experiment to examine the possibility of treating carcass while making compost with a horizontal cylinder composting equipment. The findings were as follows: as for heavy metal content, zinc content was above the allowed level in some measuring sections of the general operation and the entire measuring sections of the carcass operation, whose copper content was higher than the general operation. The wood chip operation was lower than the allowed level in all the heavy metals and similar or the same as the carcass operation in copper, cadmium and arsenic. Its nickel content was 29.5~63.8%, which was relatively higher than 9.3~18.0% and 15.8~18.0% of the general and carcass operation, respectively. Its chrome content was 14.2~31.9%, which was relatively higher than that of the general and carcass operation. The integrated operation was lower than the allowed level in all the heavy metals. Its copper and zinc content was 34.9~54.5% and 53.1~75.9%, which was similar to 48.9~52.6% and 64.6~85.9%, respectively, in the wood chip operation. Its chrome and nickel content was stabilized while their content was rather high in the wood chip operation. The average and final moisture content of the carcass operation was 60.7% and 49.6%, respectively. Its average moisture content was a little bit higher than the recommended level of 55.0%, but its final moisture content was lower than the recommended level. The average and final moisture content of the integrated operation was 29.2% and 18.6%, respectively, which was the lowest level among the four operation modes. The overall moisture content of the operation modes was under the recommended level of 55.0% with some variance among the modes. The C/N ratio was the lowest in the carcass operation and the highest in the general operation. The average C/N ratio of the operation modes was in the range of 13.7~20.3 with the total average of 18.3, and the modes kept it under the proper level of 30.0.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.4
• /
• pp.254-261
• /
• 2020

Purpose: The purpose of this study was to assess the marginal and internal fit of interim crowns fabricated by two different manufacturing method (subtractive manufacturing technology and additive manufacturing technology). Materials and Methods: Forty study models were fabricated with plasters by making an impression of a master model of the maxillary right first molar for ceramic crown. On each study model, interim crowns (n = 40) were fabricated using three types of 3D printers (Meg-printer 2; Megagen, Zenith U; Dentis, and Zenith D; Dentis) and one type milling machine (imes-icore 450i; imes-icore GmbH). The internal of the interim crowns were filled with silicon and fitted to the study model. Internal scan data was obtained using an intraoral scanner. The fit of interim crowns were evaluated in the margin, absolute margin, axial, cusp, and occlusal area by using the superimposition of 3D scan data (Geomagic control X; 3D Systems). The Kruskal-wallis test, Mann-Whitney U test and Bonferroni correction method were used to compare the results among groups (α = 0.05). Results: There was no significant difference in the absolute marginal discrepancy of the temporary crown manufactured by three 3D printers and one milling machine (P = 0.812). There was a significant difference between the milling machine and the 3D printer in the axial and occlusal area (P < 0.001). The temporary crown with the milling machine showed smaller axial gap and higher occlusal gap than 3D printer. Conclusion: Since the marginal fit of the temporary crown produced by three types of 3D printers were all with in clinically acceptable range (< 120 ㎛), it can be sufficiently used for the fabrication of the temporary crown.

• Journal of Environmental Impact Assessment
• /
• v.32 no.1
• /
• pp.1-14
• /
• 2023

When carrying out development projects around Ardeidae breeding habitats, we intend to devise a plan for sustainable coexistence by presenting measures to select and reduce key evaluation items so that conflicts can be prevented in advance at the environmental impact assessment stage. The results of the study are as follows. The main evaluation items are animal and plant items for preservation of Ardeidae breeding habitats and odor and noise items that can evaluate the effects of odors and noise in Ardeidae breeding habitats. First, the scope of the survey in animals and plants categories is not limited to legal guardian species, but includes egrets breeding and feeding grounds corresponding to major species breeding grounds and migratory birds, and preservation measures are established according to the reduction of the area of breeding and feeding grounds. Second, in the odor category, the irradiation period includes the period when the odor generation is the highest from the end of June to the end of July. The odor evaluation standard is based on the complex odor discharge standard, which is a concentration regulation, and the odor concentration felt by humans shall be 2 to 5OU/m³ and the frequency shall be 2% or less. Third, in the noise category, the timing of the survey is measured every month from May to August, including when the sound of egrets and young birds is combined to maximize noise generation. Since the noise of Ardeidae, a bird in summer, occurs only for a certain period of time, measures are taken to reduce noise by securing separation distances, securing buffer green areas, and installing construction rather than installing artificial structures such as soundproof walls. In order for existing Ardeidae breeding sites to maintain an appropriate density of populations and not move populations elsewhere, it is necessary to manage nesting tree and maintain stable habitat quantity and quality.

• Korean Journal of Remote Sensing
• /
• v.39 no.3
• /
• pp.363-370
• /
• 2023

Various earth observation satellites need to provide accurate and high-quality data after launch. To maintain and enhance the quality of satellite data, it is crucial to employ a cross-calibration process that accounts for differences in sensor characteristics, such as the spectral band adjustment factor (SBAF). In this study, we utilized Landsat-8 and Sentinel-2A satellite imagery collected from desert sites in Libya4, Algeria3, and Mauritania2 among pseudo-invariant calibration sites to calculate and apply SBAF, thereby compensating the uncertainties arising from variations in bandwidths. We quantitatively compared the reflectance differences based on the similarity of bandwidths, including Blue, Green, Red, and both the near-infrared (NIR) narrow, and NIR bands of Sentinel-2A. Following the application of SBAF, significant results with reflectance differences of approximately 1% or less were observed for all bands except NIR. In the case of the Sentinel-2A NIR band, it exhibited a significantly larger bandwidth difference compared to the NIR narrow band. However, after applying SBAF, the reflectance difference fell within the acceptable error range (5%) of 1-2%. It indicates that SBAF can be applied even when there is a substantial difference in the bandwidths of the two sensors, particularly in situations where satellite utilization is limited. Therefore, it was determined that SBAF could be applied even when the bandwidth difference between the two sensors is large in a situation where satellite utilization is limited. It is expected to be helpful in research utilizing the quality and continuity of satellite data.

• Journal of Food Hygiene and Safety
• /
• v.38 no.6
• /
• pp.489-495
• /
• 2023

In this study, we detected the presence of residual pesticides in 341 agricultural products collected from local food outlets in western Gyeonggi Province. Residual pesticides were detected in 105 (30.8%) samples. Six samples exceeded the legal limits for residual pesticides, resulting in a non-compliance rate of 1.8%, which was slightly higher than the average non-compliance rate of 1.4% in the last three years. Among the tested agricultural products, only fruits and vegetables were found to have pesticide residues, with 24 of 34 fruits (a detection rate of 70.6%) and 81 of 277 vegetables (a detection rate of 29.2%) testing positive. In total, 59 types of pesticides, including acetamiprid, which was detected 208 times, were detected and had a detection range of 0.01-2.38 mg/kg. Among the 105 agricultural products containing pesticide residues, a single pesticide was detected in 62 samples (59%) and two or more pesticides were detected in 43 samples (41%). In particular, 14 pesticides were detected in the same sample of peaches; dinotefuran was detected 21 times. Upon examining the toxicity of the detected pesticides, Class III pesticides (moderate toxicity) were detected 44 times (21.2%) and Class IV pesticides (low toxicity) were detected 164 times (78.8%). Class I, II, and III pesticides with fish toxicity were detected 68 (32.7%), 14 (6.7%), and 126 times (60.6%), respectively. Upon examining the exposure to high-frequency pesticide components detected five or more times, the hazard index was found to be ≤2.8%. Accordingly, the hazard of residual pesticides based on dietary intake was deemed insignificant.

• The Korean Journal of Pesticide Science
• /
• v.18 no.3
• /
• pp.130-140
• /
• 2014

Recently, some of the previous studies reported that tolclofos-methyl is still exist in ginseng cultivated soil, even though it is has been banned for ginseng. Therefore, the current study was aimed to examine the levels of absorption and translocation of tolclofos-methyl from ginseng cultivated soil to ginseng root and leaf stem for the period of 1 year. For this study, ginseng plants were transplanted in pots and treated with $5.0mg\;kg^{-1}$ of tolclofos-methyl (50% WP). At the end of each interval periods (every three months) the samples (soil, roots and leaf stems) were collected and analyzed the absorption and translocation levels of tolclofos-methyl using gas chromatography and mass spectrometry (GC-MS). The limit of quantitation of tolclofos-methyl was found to be $0.02mg\;kg^{-1}$ and 70.0~120.0% recovery was obtained with coefficient of variation of less than 10% regardless of sample types. In this study, a considerable amount of translocation of tolclofos-methyl residues were found in soil (4.28 to $0.06mg\;kg^{-1}$), root (7.09 to $1.54mg\;kg^{-1}$) and leaf stem (0.79 to $0.69mg\;kg^{-1}$). The results show that the tolclofos-methyl was absorbted and translocated from ginseng cultivated soil to ginseng root and ginseng leaf stem and found to be decreased time-coursely. Secondly, we were also analyzed soil, root and leaf stems samples from Hongcheon, Cheorwon, Punggi and Geumsan by GC-MS/MS (172 pesticides), LC-MS/MS (74 pesticides). In this study, 43 different pesticides were detected ($0.01{\sim}7.56mg\;kg^{-1}$) in soil, root and leaf stem. Further, tolclofos-methyl was detected 4 times separately in root sample alone which is less ($0.01{\sim}0.05mg\;kg^{-1}$) than their maximum residual limit (MRL) in ginseng. Consequently, the results from both studies indicate the residues of tolclofos-methyl found in ginseng cultivated soil and ginseng ensuring their safety level. Moreover, long-term evaluations are needed in order to protect the soil as well as ginseng free from tolclofos-methyl residues.

• 한국사회복지학회:학술대회논문집
• /
• 2003.10a
• /
• pp.185-216
• /
• 2003

This study was aimed at investigating important factors influencing career success among regular workers. The current researcher scrutinized the degree to which variables and factors affect the career success and occupational turnover rates of the research participants. At the same tune, two hypothetical path models established by the researcher were examined using linear multiple regression methods and the LISREL. After examining the differences among the factors of career success, a comparison was made between the disabled worker group and the non-disabled worker group. A questionnaire using the 5-point Likert scale was distributed to a group of 374 workers with disabilities and 463 workers without disabilities. For the data analysis purpose, the structural equation model, factor analysis, correlation analysis, and multiple regression analysis were carried out. The results of this study ran be summarized as follows. First, the results of factor analysis showed important categories of conceptual themes of career success. The initial conceptual factor model did not accord with the empirical one. A three-factorial model revealed categories of personal, family, and organizational factor respectively. The personal factor was composed of the self-esteem and self-efficiency. The family factor was consisted of the multi-roles stress and the number of children. Finally, the organizational factor was composed of the capacity for utilizing resources, networking, and the frequency of mentoring. In addition, the total 10 sub areas of career success were divided by two important aspects; the subjective career success and the objective career success. Second, both research participant groups seemed to be influenced by their occupational types. However, all predictive variables excluding the wage rate and the average length of work years had significant impact on job success for the disabled work group, while all the variables excluding the frequency of advice and length of working years had significant impact on job success for the non-disabled worker group. Third, the turnover rate was significantly influenced by the age and the experience of turnover of the research participants. However, the number of co-workers was the strongest predictive variable for the worker group with disabilities, but the occupation choice variable for the worker group without disabilities. For the disabled worker group, the turnover rate was differently influenced by the type of occupation, the length of working years, while multi-role stress and the average working years at the time of turnover for the worker group without disabilities. Fifth, as a result of verifying the hypothetical path model, it showed that the first model was somewhat proper and could predict the career success on both research participant groups. In the second model, the Chi-square, the degree of freedom (($x^2=64.950$, df=61, P=0.341), and the adjusted Goodness of Fit Index (AGFI) were .964, and the Comparative Fit Index (CFI) were .997, and the Root Mean Squared Residual (RMR) was respectively. .038. The model was best fitted and could predict the career success more highly because the goodness of fit index in the whole models was within the allowed range. In conclusion, the following research implications can be suggested. First, the occupational type of research participants was one of the most important variables to predict the career success for both research participant groups. It means that people with disabilities require human development services including education. They need to improve themselves in this knowledge-based society. Furthermore, for maintaining the career success, people with disabilities should be approached by considering the subjective career success aspects including wages and the promotion opportunities than the objective career success aspects.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.8-12
• /
• 1974

1. If one unity is given to the prongs whose ends touch each other for estimating the internal stresses occuring in it, the internal stresses which are developed in the open prongs can be evaluated by the ratio to the unity. In accordance with the above statement, an equation was derived as follows. For employing this equation, the prongs should be made as shown in Fig. I, and be measured A and B' as indicated in Fig. l. A more precise value will result as the angle (J becomes smaller. $CH=\frac{(A-B') (4W+A) (4W-A)}{2A[(2W+(A-B')][2W-(A-B')]}{\times}100%$ where A is thickness of the prong, B' is the distance between the two prongs shown in Fig. 1 and CH is the value of internal stress expressed by percentage. It precision is not required, the equation can be simplified as follows. $CH=\frac{A-B'}{A}{\times}200%$ 2. Under scheduled drying condition III the kiln, when the weight of a sample board is constant, the moisture content of the shell of a sample board in the case of a normal casehardening is lower than that of the equilibrium moisture content which is indicated by the Forest Products Laboratory, U. S. Department of Agriculture. This result is usually true, especially in a thin sample board. A thick unseasoned or reverse casehardened sample does not follow in the above statement. 3. The results in the comparison of drying rate with five different kinds of wood given in Table 1 show that the these drying rates, i.e., the quantity of water evaporated from the surface area of I centimeter square per hour, are graded by the order of their magnitude as follows. (1) Ginkgo biloba Linne (2) Diospyros Kaki Thumberg. (3) Pinus densiflora Sieb. et Zucc. (4) Larix kaempheri Sargent (5) Castanea crenata Sieb. et Zucc. It is shown, for example, that at the moisture content of 20 percent the highest value revealed by the Ginkgo biloba is in the order of 3.8 times as great as that for Castanea crenata Sieb. & Zucc. which has the lowest value. Especially below the moisture content of 26 percent, the drying rate, i.e., the function of moisture content in percentage, is represented by the linear equation. All of these linear equations are highly significant in testing the confficient of X i. e., moisture content in percentage. In the Table 2, the symbols are expressed as follows; Y is the quantity of water evaporated from the surface area of 1 centimeter square per hour, and X is the moisture content of the percentage. The drying rate is plotted against the moisture content of the percentage as in Fig. 2. 4. One hundred times the ratio(P%) of the number of samples occuring in the CH 4 class (from 76 to 100% of CH ratio) within the total number of saplmes tested to those of the total which underlie the given SR ratio is measured in Table 3. (The 9% indicated above is assumed as the danger probability in percentage). In summarizing above results, the conclusion is in Table 4. NOTE: In Table 4, the column numbers such as 1. 2 and 3 imply as follows, respectively. 1) The minimum SR ratio which does not reveal the CH 4, class is indicated as in the column 1. 2) The extent of SR ratio which is confined in the safety allowance of 30 percent is shown in the column 2. 3) The lowest limitation of SR ratio which gives the most danger probability of 100 percent is shown in column 3. In analyzing above results, it is clear that chestnut and larch easly form internal stress in comparison with persimmon and pine. However, in considering the fact that the revers, casehardening occured in fir and ginkgo, under the same drying condition with the others, it is deduced that fir and ginkgo form normal casehardening with difficulty in comparison with the other species tested. 5. All kinds of drying defects except casehardening are developed when the internal stresses are in excess of the ultimate strength of material in the case of long-lime loading. Under the drying condition at temperature of $170^{\circ}F$ and the lower humidity. the drying defects are not so severe. However, under the same conditions at $200^{\circ}F$, the lower humidity and not end coated, all sample boards develop severe drying defects. Especially the chestnut was very prone to form the drying defects such as casehardening and splitting.