• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2008

Technisium $(^{99m}Tc)$ is one of the most widely used radioactive isotopes for diagnosis in nuclear medicine. In general, technisium is produced inside the so called $^{99m}Tc$ generator which is usually made out of lead to shield relatively high energy radiation from $^{99}Mo$ and its daughter nuclide $^{99m}Tc$. In this paper, a GEANT4 simulation is carried out to test the safety of the $^{99m}Tc$ generator, taking the Daiichi product with radioactivity of 500 mCi as an example. According to the domestic regulation on radiation safety, the dose at 10 cm and 100 cm away from the surface of shielding container should not exceed 2.0 mSv/h and 0.02 mSv/h, respectively. The simulated dose turned out to be less than the limit, satisfying the domestic regulation.

• Journal of the Korean Society of Radiology
• /
• v.12 no.2
• /
• pp.133-138
• /
• 2018

The measurement of gamma-ray spectrum of $^{nat}W(p,xn)$ reaction with natural tungsten were performed by using a high energy proton generated from a 100-MeV proton linear accelerator of the Korea Multi-purpose Accelerator Complex (KOMAC). Gamma rays generated by various nuclides generated through the nuclide were measured using a gamma-ray spectroscopy system composed of HPGe detector. A gamma-ray standard source was used for energy calibration and efficiency measurement of the detector. Analysis of the gamma rays observed in the measured spectra showed that the radionuclides produced were $^{167}Re$, $^{178}Re$, $^{179}Re$, $^{180}Re$, $^{181}Re$, $^{182}Re$, $^{184}Re$, $^{172}Ta$, $^{174}Ta$, $^{178}Ta$, $^{182}Ta$, $^{184}Ta$, $^{175}W$, $^{176}W$, $^{177}W$ and $^{179}W$. Nuclides were generated. The results of this study will be applied to nuclear fusion, astrophysics, and nuclear medicine applications in the future.

• Progress in Medical Physics
• /
• v.13 no.1
• /
• pp.44-50
• /
• 2002

CsI(T1) single crystal was grown in a Bridgman growing apparatus, which has the diameter of 11 mm and the mole ratio of 0.001 mol%. Radiation sensors were made with CsITl)crystal and two photodiodes, and measured spectroscopic characteristics and linearity for gamma-ray and X-ray. The energy resolution of CsI(T1) radiation sensor has been measured with $^{22}$ Na, $^{137}$ Cs and $^{60}$ Co gamma standard sources. Also output linearity of CsITl) sensor was measured for diagnostic radiation region. The energy resolutions of CsI(T1) radiation sensor for 0.511MeV gamma-ray from Na-22 source, 0.662MeV from Cs-137 source, and 1.17MeV and 1.332MeV from Co-60 source were 13.2%, 8.3%, 6.7%, and 5.1% respectively. Also the output linearity up to 80mAs current for 60kVp, 80kvp, 100kVp, 120kVp tube voltages has been studied.

• Progress in Medical Physics
• /
• v.20 no.4
• /
• pp.216-224
• /
• 2009

$^{131}I$ is a radiological isotope being used widely for treatment of cancer as emitting gamma-ray and it is also applied to estimate the function of thyroid for its accumulation in thyroid. However, $^{131}I$ is more difficult to quantitate comapred to $^{99m}Tc$, because $^{131}I$ has multiple energy gamma-ray emissions compared to $^{99m}Tc$ which is a mono energetic gamma-ray source. Especially, scattered ray and septal penetration resulted by high energy gamma ray have a bad influence upon nuclear medicine image. The purpose of this study was to estimate scatter components depending on the different source locations within a phantom using Monte Carlo simulation (GATE). The simulation results were validated by comparing with the results of real experiments. Dual-head gamma camera (ECAM, Chicago, Illinois Siemens) with high energy, general-purpose, and parallel hole collimators (hole radius: 0.17 cm, septal thickness: 0.2 cm, length: 5.08 cm) was used in this experiment. The NaI crystal is $44.5{\times}59.1\;cm$ in height and width and 0.95 cm in thickness. The diameter and height of PMMA phantom were 16 cm and 15 cm, respectively. The images were acquired at 5 different locations of $^{131}I$ point source within the phantom and the images of $^{99m}Tc$ were also acquired for comparison purpose with low energy source. The simulation results indicated that the scattering was influenced by the location of source within a phantom. The scattering effects showed the same tendency in both simulation and actual experiment, and the results showed that the simulation was very adequate for further studies. The results supported that the simulation techniques may be used to generalize the scattering effects as a function of a point source location within a phantom.

• Progress in Medical Physics
• /
• v.19 no.4
• /
• pp.291-297
• /
• 2008

The purpose of this study is to optimize a parallel-hole collimator for small gamma camera having the pixellated crystal array and evaluate the effect of crystal-collimator misalignment on the image quality using a simulation tool GATE (Geant4 Application for Tomographic Emission). The spatial resolution and sensitivity were measured for the various size of hexagonal-hole and matched square-hole collimators with a Tc-99m point source and the uniformity of flood image was estimated as a function of the angle between crystal array and collimator by misalignment. The results showed that the spatial resolution and sensitivity were greatly improved by using the matched collimator and the uniformity was reduced by crystal-collimator misalignment.

• Progress in Medical Physics
• /
• v.18 no.1
• /
• pp.42-47
• /
• 2007

Purpose: To evaluate the tracing of optic nerve tract using manganese enhanced magnetic resonance Imaging. Materials and Methods: After injecting $30{\mu}l$ of $MnCl_2(1mol)$ (1 mol) Into the retina of female New Zealand white rabbit, the contrast enhancements at major anatomical structures of optic nerve tract were evaluated by high resolution T1-weighted Images 12 hours, 24 hours, and 48 hours after $MnCl_2(1mol)$ Injection using 3D FSPGR (Fast Speiled Gradient Recalled echo) pulse sequence at 1.5T clinical MR scanner with high performance gradient system. Also, for quantitative evaluation, the signal-to-noise ratios of circular ROI on anatomical locations were measured. Results: The major structures on the optic nerve tract were enhanced after injecting $MnCl_2(1mol)$. The structures, which showed enhancement, were right optic nerve, optic chiasm, left optic tract, left lateral geniculate nucleus, left superior colliculus. The structures on the contralateral optic pathway to the right retina were enhanced whereas the structures on the ipsilateral pathway did not show enhancement. Conclusion: The Mn transport through axonal pathway of optic nerve sys)em was non- invasively observed after injecting injecting $MnCl_2$ at the retina, which is the end terminal of optic nerve system. This Mn transport seems to occur by voltage gated calcium $(Ca^{2+})$ channel and In case of direct Injection Into the retina, the fast transpori pathway of voltage gated calcium channel seems to be responsible for Mn transport.

• Progress in Medical Physics
• /
• v.24 no.3
• /
• pp.176-182
• /
• 2013

Through this research, we measure the data for several SUVs such as SUVLBM, SUVBW, and SUVBSA using volume of interest in order to enhance the diagnostic level in whole-body image for healthy examinees via F-18 FDG PET/CT. Maximum value, mean value, standard deviation, and threshold value for each SUVs are shown. The measurement of SUVs are carried out with 31 examinees who have taken whole-body examination with F-18 FDG PET/CT from July, 2012 to August, 2012. To secure the preciseness of measurement, we selected 26 healthy examinees as a subject of measurement according to diagnostic view of a nuclear-medical doctor. We see from the measurement of SUVs of PET/CT that the value of SUVBW is hightest and followed by SUVLBM and SUVBSA in turn regardless of the use of contrast media. By comparing the SUVLBM-maximum data for the group used contrast media with those for the group used no contrast media, there found a trend that the measured values increase when the contrast media are used. Among them, liver, aorta, lumbar-5, and Cerebellum exhibit significant difference (p<0.05). We conclude that our data for SUVs would be basic references in overall image interpretation, and hope that the research using VOI would be active.

• Progress in Medical Physics
• /
• v.26 no.1
• /
• pp.18-27
• /
• 2015

Since a Compton camera has high detection sensitivity due to electronic collimation and a good energy resolution, it is a potential imaging system for nuclear medicine. In this study, we investigated the feasibility of a Compton camera for multi-tracer imaging and proposed a rotating Compton camera to satisfy Orlov's condition for 3D imaging. Two software phantoms of 140 and 511 keV radiation sources were used for Monte-Carlo simulation and then the simulation data were reconstructed by listmode ordered subset expectation maximization to evaluate the capability of multi-tracer imaging in a Compton camera. And the Compton camera rotating around the object was proposed and tested with different rotation angle steps for improving the limited coverage of the fixed conventional Compton camera over the field-of-view in terms of histogram of angles in spherical coordinates. The simulation data showed the separate 140 and 511 keV images from simultaneous multi-tracer detection in both 2D and 3D imaging and the number of valid projection lines on the conical surfaces was inversely proportional to the decrease of rotation angle. Considering computation load and proper number of projection lines on the conical surface, the rotation angle of 30 degree was sufficient for 3D imaging of the Compton camera in terms of 26 min of computation time and 5 million of detected event number and the increased detection time can be solved with multiple Compton camera system. The Compton camera proposed in this study can be effective system for multi-tracer imaging and is a potential system for development of various disease diagnosis and therapy approaches.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.154-155
• /
• 2010

최근 Stranski-Krastanov (SK) 성장법을 이용한 자발형성 (Self-assembled) InAs/GaAs 양자점 (Quantum Dot) 연구가 기초 물리학뿐만 아니라 응용에 있어 활발하게 진행되고 있다. 그러나 기존 보고에 따르면 SK 성장법을 통한 InAs/GaAs 양자점은 크기, 균일도, 및 밀도 등의 성장거동 제어에 한계가 있다. 예로, 성장속도 및 증착양이 감소하더라도 상대적으로 크기가 큰 InAs/GaAs 클러스터 (Cluster)를 형성하여 크기분포의 불균일 및 결함을 야기하여 결과적으로 전기/광학적 특성을 저해하는 요인이 된다. 이를 개선하기 위한 방안으로 SK 성장법을 변형한 다양한 수정자발형성법이 제안되어 연구되고 있다. 본 논문에서는 기존 SK 성장법과 Arsenic-interruption Technique(AIT), In Pre-deposition (IPD)법을 각각 접목한 수정자발형성법을 이용하여 상대적으로 크기가 큰 InAs/GaAs 양자점 또는 클러스터 형성을 감소시켜 공간적 크기 균일도 및 밀도를 제어한 결과를 보고한다. 성장된 InAs/GaAs 양자점 시료의 구조 및 광학적 특성을 원자력간현미경 (Artomic Force Microscopy, AFM)과 Photoluminescence (PL) 분광법을 이용하여 분석하였다. 기존 SK 성장법을 이용하여 형성한 기준시료의 AFM 이미지에서 InAs/GaAs 양자점과 클러스터의 공간밀도는 각각 6.4*1010/cm2와 1.4*109/cm2로 관찰되었다. 그러나, AIT를 이용한 양자점 시료의 경우 상대적으로 크기가 큰 InAs/GaAs 클러스터는 관찰되어지지 않았고, 양자점 밀도는 8.4*1010/cm2로 SK 양자점에 비하여 30% 정도 개선되었다. 또한, InAs/GaAs 클러스터를 제외한 공간 균일도는 SK-InAs/GaAs 양자점의 15.6%에 비하여 8%로 크게 개선된 결과를 얻었다. AIT 성장법을 이용한 InAs/GaAs 양자점에서 원자의 이동거리 (Migration Length)의 제어로 양자점의 형성특성이 개선된 것으로 설명할 수 있으며, Arsenic 차단 시간이 임계점 이상으로 길어지면 다시 InAs/GaAs 클러스터들이 형성되는 것을 관찰할 수 있었다. InAs/GaAs 양자점과 클러스터 형성 특성이 초기 표면 조건에 어떻게 영향을 받는지 분석하기 위해, InAs 양자점 성장 이전에 V족 물질 공급 없이 Indium의 공급시간을 1초(IPDT1S 시료), 2초 (IPDT2S 시료), 3초 (IPDT1S 시료)로 변화시키면서 증착하고 기존 SK 성장법으로 양자점을 성장하였다 (IPD성장법). 그 결과 IDP1S 양자점 시료의 공간밀도가 10*1010/cm2로 SK InAs/GaAs 양자점 시료에 비해 약 60% 정도 증가하였고, 클러스터도 관찰 할 수 없었다. 그러나 IPD 시간이 증가할수록 다시 InAs/GaAs 클러스터들이 형성되는 것을 관찰할 수 있었다. 이러한 결과는 InAs/GaAs 양자점 성장초기에 InAs 핵생성 사이트 (Nucleation site)의 크기 및 상태를 제어하는 것이 양자점의 밀도 및 균일도를 제어하는 중요한 요소임을 알 수 있다.

• Progress in Medical Physics
• /
• v.14 no.2
• /
• pp.74-80
• /
• 2003

The purpose of this study was to evaluate the performance of the teflon encapsulated TLD rod, which may be used in nuclear medicine for the direct in vivo measurements of radiation dose. We analyzed the influence of teflon encapsulation for measuring absorbed dose. An experiment was carried out to evaluate and observe the response of a LiF TLD-100 rod in a thin-wall teflon capsule at different depths in a solid phantom. An adult anthropomorphic phantom was used to measure the absorbed dose using thin teflon encapsulated TLD. The measurements of PDD-, and TMR in solid phantom and athe bsorbed dose in humanoid phantom performed with normal TLD were compared with values obtained by teflon encapsulated TLD. It was demonstrated that the difference of TL response of LiF in phantom with and without teflon thin-wall capsule was less than 3％ under the same conditions beyond the build-up region. However, significant differences were observed near the phantom surface because of the build-up effect caused by the thin-wall thickness of the teflon capsule. Thus, our study showed that the contribution of teflon thin-wall capsule to TLD response for the megavoltage photon beams was negligible and that it did not significantly effect dose measurement. The teflon encapsulated TLD described in this work has been proven to be appropriate for in vivo dosimetry in therapeutic environments.