• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.5
• /
• pp.278-284
• /
• 2014

Water temperature due to climate change can be estimated using the air temperature because the air and water temperatures are closely related and the water temperatures have been widely used as the indicators of the environmental and ecological changes. It is highly necessary to estimate the frequency distribution of the air and water temperatures, for the climate change derives the change of the coastal water temperatures. In this study, the distribution function of the air temperatures is estimated by using the long-term coastal air temperature data sets in Korea. The candidate distribution function is the bi-modal distribution function used in the previous studies, such as Cho et al.(2003) on tidal elevation data and Jeong et al.(2013) on the coastal water temperature data. The parameters of the function are optimally estimated based on the least square method. It shows that the optimal parameters are highly correlated to the basic statistical informations, such as mean, standard deviation, and skewness coefficient. The RMS error of the parameter estimation using statistical information ranges is about 5 %. In addition, the bimodal distribution fits good to the overall frequency pattern of the air temperature. However, it can be regarded as the limitations that the distribution shows some mismatch with the rapid decreasing pattern in the high-temperature region and the some small peaks.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.15 no.3
• /
• pp.257-262
• /
• 2009

The unified power flow controller(UPFC) is one of the most effective devices in the FACTS family. This paper concerns about a filtering technique for reducing the computer calculation to determine the optimal location of UPFC in a power system. The sensitivities of the power generation cost for UPFC control parameters are evaluated. This technique requires that only one optimal power flow is run to get UPFC sensitivities for all possible transmission lines. To find out a optimal locating of a single UPFC in power system, an ideal transformer model which consists of a complex turns ratio and a variable shunt admittance was used. In this model, the UPFC control variables do not depend on UPFC input and output currents and voltages. The sensitivity method was tested on a 5-bus system derived from the IEEE 14-bus system and IEEE 14-bus system to establish its effectiveness.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.254-262
• /
• 2015

Parametric study on submerged body shape of an oscillating hemisphere point absorber was conducted to predict the optimal relation between radius and draft of the body. As an additional damping due to power takeoff system, the optimal damping same as wave radiation damping was applied to the PTO system to produce the maximum wave power. Body response spectrum and power spectrum were obtained for various peak frequencies on wave spectra. It was found that the maximum power can be generated when the peak frequency of available wave power was 20% greater than that of wave spectrum.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.3
• /
• pp.295-300
• /
• 2011

Ship are a box-shaped structure. It is used often fore and aft parts, bilge strake, deck with camber of ship structures. When this structure is compared with flat plate structure, it different to behaviour. Generally, if it subjected to axial compressive load, ultimate strength depend on the change of curvature. Also, In this paper, stiffened curved plate with 1/2+1+1/2 bay model subjected to compressive load carried out the elasto-plastic large deflection series analysis. and parameter effect considered slender ratio, web height/thickness as well as change of curvature and investigated collapse mode for analysis model.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.2
• /
• pp.161-167
• /
• 2017

This paper measured and evaluated the technical efficiency, pure technical efficiency and scale efficiency of port labor via three inputs and three outputs using Data Envelopment Analysis (DEA). First, the average overall technical efficiency measured about 94.18 %, with 100 % pure technical efficiency being larger than 94.18% scale efficiency. As a result, 7 ports were identified as efficient, and 4 ports were identified as inefficient. Among the 4 ineffiecient ports, Donghae had the highest Increasing Return to Scale (IRS). However, the inefficient ports were all found to be less efficient in terms of resource operation than production scale. On the other hand, the efficient ports established priorities using the super efficiency method. As a result, port efficiency was highest for Incheon, Mokpo, Pyeongtaek-Dangjin, Masan, Yeosu Gwangyang, Jeju, and Gunsan-Daesan Ports, in order. In particular, Busan Port, found to be inefficient, would benefit from using Mokpo Port and Incheon Port as benchmarks to increase trade volume and modernize equipment for full-scale commercialization to improve labor efficiency.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.5
• /
• pp.515-520
• /
• 2007

Recently, the treat of sludge is usually progressed by ocean disposal. But it will be totally banned by content of its heavy metal according to London Dumping Convention, gradually. The stable way of treat of sewage sludge should be examined urgently. To solve the problem, recently, there are efficient and environment-oriented method. One of them is to produce absorbent through the activation. This study produces absorbent through steam activation. As basic experiment, optimum activation condition for preparation of good absorbent is researched through study of the fellowing variables : steam flow rate, activated temperature, activation time. As the result of this with standard on iodine adsorptivity, it is chosen, that steam flow rate "30 mL/hr", activation temperature $"500^{\circ}C"$, activation time "60 minutes". At the time, iodine adsorptivity and yield shown that 228.4 mg/g, 77.23%. And also, by using nitrogen adsorption, SEM and EDS are confirmed that pore development, specific surface area, mean pore size, chemical component and content. Pore developed by steam activation is also confirmed that it is micropore.

• KIISE Transactions on Computing Practices
• /
• v.23 no.12
• /
• pp.660-669
• /
• 2017

In order to improve user accessibility and interactivity, system scalability, service speed, and a non-standard internet web environment, we developed a Web-based geovisualization system of oceanographic information using HTML5 and dynamic particles. In particular, oceanographic and meteorological data generated from a satellite remote sensing and radar measurement and a 3-dimensioanl numerical model, has the characteristics of a heterogeneous large-capacity multi-dimensional continuous spatial and temporal variability, based on geographic information. Considering those attributes, we applied dynamic particles represent the spatial and temporal variations of vector type oceanographic data. HTML5, WebGL, Canvas, D3, and Leaflet map libraries were also applied to handle various multimedia data, graphics, map services, and location-based service as well as to implement multidimensional spatial and statistical analyses such as a UV chart.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.2
• /
• pp.231-239
• /
• 2019

In sonar systems, the passive ranging of a target is an active research area. This paper analyzed the performance of passive ranging based on an array invariant method for different environmental and sonar parameters. The array invariant developed for source range estimation in shallow water. The advantages of this method are that detailed environmental information is not required, and the real-time ranging is possible since the computational burden is very small. Simulation was performed to verify the algorithm. And this method is applied to sea-going experimental data in 2013 near Jinhae port. This study shows the performance of ranging for source orientation, transmission signal length, and length of a receiver through numerical simulation experiments. Also, the results using nested array and uniform line arrays are compared.

• Journal of Environmental Science International
• /
• v.5 no.3
• /
• pp.329-335
• /
• 1996

This project studies marine Vibrio vulnificus in oysters in the marine environment and attempts to correlate this bacteria's presence within various environmental parameters; we design this study to determine how different storage temperatures affect the survival of V. vuinficus in oysters and whether V. vulnificus is able to persist in oysters after exposure to UV light-disinfected seawater. Experimental depuration systems consist of aquaria containing temperature-controlled seawater treated with UV light and 0.2 ㎛ pore size filtration. Results showed that depuration at temperatures higher than 25℃ caused V. vuinificus counts to increase in oysters. Throughout the process, depuration water contained high concentrations of U vuinificus indicating"that the disinfection properties of UV radiation and 0.2 ㎛ pore size filtration were less than 어e release of V. vuinificus into seawater, In contrast, when depuration seawater was maintained at 10℃, the numbers of V. vuinificus were very little and multiplication in oysters was inhibited.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.321-321
• /
• 2015

해수 환경에 노출된 대부분의 금속재료는 직 간접적으로 부식의 영향을 받는다. 이와 같이 해수에 침지된 금속재료의 부식 방지에는 음극방식법이 주로 사용되고 있다. 과거의 음극방식 설계에는 양극 크기와 방식전류 밀도, 소모율 등 양극 자체에 대한 변수만이 고려되었으나, 20여 년 전부터는 해수 오염도, 수온 및 유속 등을 종합적으로 고려하여 설계하고 있다. 특히 대부분의 금속은 부식성 환경에서 생성된 부동태 피막이 해수 유동에 의해 파괴되면서 급속히 손상된다. 따라서 본 연구에서는 해수 특성을 고려한 최적의 소요방식전류밀도 선정을 위해 전기화학실험을 실시하였다. 실험 결과, 해수 온도 상승에 따라 확산속도가 빨라져 최적 방식 전류밀도가 증가하는 경향을 나타냈다.