• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.120-120
• /
• 2018

반도체 소자나 디스플레이 패널 제조 공정에 가장 많이 사용되는 진공 펌프인 터보 분자 펌프는 오일을 사용하지 않고, 설치 방향이 자유로우며 넓은 작동 압력 영역을 가지고 있어서 고가임에도 불구하고 점점 더 사용 영역을 넓혀 가고 있다. 상하의 두 곳에 회전축을 지지하는 베어링이 필요한데, 기계식 금속 베어링을 채용하는 경우에는 반드시 윤활유를 공급해 주어야 하고, 고온, 부식성 또는 산화성 가스의 배기 시에는 퍼지 가스로 비활성인 질소나 알곤등을 이용하여 보호를 해주어야 한다. 반면, 자기 베어링을 채택한 모델은 윤활의 걱정에서 자유로울 수 있기 때문에 채용이 늘어나고 있다. 동일극의 반발력이나 반대극의 인상력을 이용한 구조를 갖게 되는데 갑작스러운 입구 쪽 압력의 증가 시에는 자석 끼리 부딪치는 일이 발생하고 이로 인해서 로터 모듈 전체에 큰 손상을 갖게 되므로 한 곳 정도에 비상용 터치 다운 베어링을 기계식으로 윤활제 없이 설치하기도 한다. 기본적으로 자기 베어링 방식은 로터 모듈의 부상과 제어를 위해서 3축 또는 5축 제어를 하게 되는데 여기에는 전자석의 전류를 미세하게 조정하여 피드백 하는 시스템을 활용하기 때문에 외부에서의 자기장이 일정값 이상 침투하게 되면 제어 회로의 기능에 문제를 일으키게 된다. 또한 축 방향에 수직인 자기장의 강도가 높아지면 고속으로 회전하는 금속 블레이드가 자속을 자르게 되므로 표면에 와전류가 발생하여 문제가 된다. 터보 분자 펌프는 회전자와 고정자 간격이 1 mm 이내로 작아서 약간의 진동이라도 발생하면 회전자와 고정자 간에 충돌이 일어나고 이는 곧 파손으로 이어진다. 그림 1에는 파손 원인 분석을 위한 회전자 모듈의 수치 해석용 모델의 일부를 나타내었고, 그림 2에는 실제로 외부 자기장에 의한 파손이 발생한 사례의 자기 베어링 모듈의 사진을 나타내었다. 본 발표에서는 외부 자기장의 형태에 따라 제어 자기장에 미치는 영향을 CFD-ACE+(ESI corp)를 활용하여 해석하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.571-577
• /
• 2017

In this numerical study, the separation efficiency of three-phase separator in an oil-sand plant was studied with various inlet head configurations. The free water knockout (FWKO) vessel was designed with a flow rate of $15.89m^3/day$ (100 bbl/day) and the SOR(stream-to-oil ratio)=3.5 was derived using Stokes' law. For modularization, optimization of the design of the inlet head configuration was performed with parallel-connected dual FWKO vessels. The feed condition of bitumen emulsion was API=17, $T_{in}=150^{\circ}C$ and $P_{in}=50bar$. A mean residence time was determined the time when 95% of the oil and water in FWKO vessel was separated. The combination between the volume of fluid (VOF) and the discrete phase model (DPM) was used to simulate the phase separation phenomenon in a multi-phase separator. Furthermore, in order to calculate multi-phase flow the pseudo-transient method was adopted.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.245-248
• /
• 2008

Recently, much research has been conducted on FRP composite to replace steel. However, the concept of FRP girder filled with concrete has not been fully attempted. This study focuses on the analytical behavior of FRP girders filled with concrete. FRP girders usually have large deflection due to relatively low elastic modulus compared to steel members. However, in the previous experimental investigation on small sized modular beams, it has been verified that the displacement of FRP-girder filled with concrete is reduced and the strength is increased considerably. In this research, analytical investigations have conducted to verify the analytical method by comparing the results with tests. In addition, analyses on large girders assembled with small modules have been carried out to predict the feasibility before tests. The analytical results showed that the assembled FRP girders can be used as substitutes for steel girders.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.1
• /
• pp.15-22
• /
• 2022

This paper introduces research on the hinge joint of modular structure joints using finite element analysis. The modular structure has a characteristic in that it is difficult to expect the integrity of columns and beams between unit modules because the construction is carried out such that the modules are stacked. However, the current modular design ignores these structural characteristics, considers the moment transmission for the lateral force, and analyzes it in the same manner as the existing steel structure. Moreover, to fasten the moment bonding, bolts are fastened outside and inside the module, resulting in an unreasonable situation in which the finish is added after assembly. To consider the characteristics that are difficult to expect, such as unity, a modular structure system using hinge joints was proposed. This paper proposed and reviewed the basic theory of joints by devising a modified scissors model that is modified from the scissors model used in other research to verify the transmission of load when changing from the existing moment junction to a hinge junction. Based on the basics, the results were verified by comparing them with Midas Gen, a structural analysis program. Additionally, the member strength and usability were reviewed by changing the modular structure designed as a moment joint to a hinge joint.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.2
• /
• pp.153-166
• /
• 2008

This paper concerns the development of a knowledge-based tunnel design system within the framework of artificial neural networks (ANNs). The system is aimed at expediting a routine tunnel design works such as determination of support patterns and stability analysis of selected support patterns. A number of sub-modules for determination of support patterns and stability assessment were developed and implemented to the system. It is shown that the ANNs trained with the results of 2D and 3D numerical analyses can be generalized with a reasonable accuracy, and that the ANN based tunnel design concept is a robust tool for tunnel design optimization. The details of the system architecture and the ANNs development are discussed in this paper.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.3 s.32
• /
• pp.71-76
• /
• 2004

The power consumption of TEC for Laser diode cooling was predicted by 3-D FEM simulation and verified by experiment. The operating conditions such as power consumption of Laser diode, set temperature, ambient temperature, resistance of thermal path was considered to estimate the TEC power consumption. Using 3-D FEM simulation, the relation between TEC configuration defined by the pellet dimension and the number and power consumption was investigated for low power consumption scheme. As a result, as the thermal resistance of the pellet increased, the power consumption decreased.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.685-692
• /
• 2009

This paper dealt with the development of the Framework for Multidisciplinary Design Optimization for the rotorcraft design concept and the building process of KHP(Korea Helicopter Project) - SDM(Simulation Data Management) system to manage various analysis data, which are used in the rotorcraft development phase. KHP-SDM RMDO(Rotorcraft Multidisciplinary Design Optimization) framework, which applied optimization modules of KHP-SDM and integrated the developed Multidisciplinary analysis modules, was constructed in the KHP-SDM. The results of the rotorcraft conceptual design using KHP-SDM RMDO showed that the framework was evaluated to be successfully constructed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1883-1897
• /
• 1993

Interactive computer-aided analysis of mechanical systems has recently been undergoing an evolution due to highly efficient computer graphics. The industrial implementation of state-of-the-art analytical developments in mechanisms has been facilitated by computer-aided design packages because these rigid-body mechanism analysis programs dramatically reduce the time required for linkage design. This paper proposes a component modular approach to computeraided kinematic motion analysis for general planar multiloop mechanisms. Most multiloop mechanisms can be decomposed into serveral components. The kinematic properties (position, velocity, and acceleration) of every node can then be determined from the kinematic analysis of the corresponding component modules by a closed-form solution procedure. In this paper, 8 types of modules are defined and formulations for kinematic analysis of the component modules are derived. Then a computer-aided kinematic analysis program is developed using the proposed approach and the solution procedure of an example shows the effectiveness and accuracy on the approach.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.78-88
• /
• 1990

To evaluate the performance of a multiprocessor system, a discrete event model of memory interference in the system employing multiple-bus interconnection networks is proposed. An analytic model of the system is presented and then simulator models are implemented for cross-verifying the analytic results and simulation results. The simulator model takes as input the number of processors, the number of memory modules, the number of buses and the local memory miss ratio. The model produces as output the memory bandwidth, the processor, memory module and bus utilization and the bus contention ratio. Using the model in the design of the system, it is possible to evaluate the system performance by analyzing the interaction of the input parameters.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.907-907
• /
• 2012

우리나라 하천의 상류에는 저수지와 댐이 다수 존재한다. 이러한 댐의 방류량은 댐 하류의 유출량에 직접적인 영향을 미치게 된다. 그러므로 댐 하류의 유출해석은 강우에 의한 유출과 댐의 방류량이 함께 고려되어야 한다. 본 연구는 분포형 강우-유출 모형인 GRM의 Flow control 모듈 중 Inlet을 이용하여 댐 방류량의 영향을 고려한 유출해석을 수행하였다. 대상 유역은 낙동강의 안동댐과 임하댐 하류에 있는 구담 수위관측소와 남강댐 하류에 있는 대곡 수위관측소 유역을 선정하였다. 유출해석 결과, 구담 유역에서는 안동 조정지댐과 임하 조정지댐의 방류량과 강우에 의한 유출을 종합적으로 해석할 수 있었다. 또한 대곡 유역에서는 남강댐의 방류량과 강우에 의한 유출을 함께 해석할 수 있었다. 본 연구를 통해서 남강댐 하류 유역과 안동댐, 임하댐 하류 유역의 유출해석시 GRM모형을 적용할 수 있는 것으로 나타났으며, 향후 다양한 저수지 유역을 대상으로 GRM모형의 적용성을 평가할 예정이다.