• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.463-470
• /
• 2014

Stealth technology of combat aircraft is most significant capability in recent air battlefield. As the detector of IR missiles is being developed, IR stealth capability which is evaluated by IR signature level become more important than it was in previous generation. Among IR signature of aircraft from various sources, aerodynamic heating dominates in long-wavelength IR spectrum of $8{\sim}12{\mu}m$. Skin temperature change by aerodynamic heating which is derived by effects of Mach number and structure. The 4th and 5th generation aircraft are selected for calculation of the skin temperature, and its height and velocity in numerical conditions are 10,000 m and Ma 0.9~1.9 respectively. Aircraft skin temperature is calculated by computing convection of fluid and conduction, convection and radiation of surface. As the aircraft accelerates to higher Mach number, maximum skin temperature increases more rapidly than average temperature and temperature distribution changes in more sharp, interactive ways. The 4th generation aircraft whose shape is more complex than that of the 5th generation aircraft have complicated temperature distribution. On the other hand, the 5th generation aircraft whose shape is relatively simple shows plain temperature distribution and lower skin temperature in terms of both average and maximum value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.688-693
• /
• 2016

This paper describes the parachute dynamics modeling and simulation results for the development of training simulator of a HALO (High Altitude Low Opening) parachute, which is currently in use for military purposes. The target parachute is a rectangular shaped parafoil and its dynamic model is derived based on the real geometry data as the 9-DOF nonlinear equations of dynamics. The simulation was conducted through the moment of inertia and its aerodynamic derivatives to reflect the real characteristics based on the MATLAB/Simulink. In particular, its modeling includes the typical characteristics of the added mass and moment of inertia, which is shown in the strong effects in Lighter-Than-Air(LTA) flight vehicle. The proposed dynamic modeling was evaluated through the simulation under the spiral turning flight conditions of the asymmetric control inputs and compared with the performance index in the target parachute manual.

• Journal of the Korea Society of Computer and Information
• /
• v.11 no.4 s.42
• /
• pp.35-45
• /
• 2006

RIn this paper. we describe real-time parallel processing simulator developed for the use of performance analysis of rolling missiles. The real-time parallel processing simulator developed here consists of seeker emulator generating infrared image signal on aircraft, real-time computer, host computer, system unit, and actual equipments such as auto-pilot processor and seeker processor. Software is developed according to the design requirements of mathematic model, 6 degree-of-freedom module, aerodynamic module which are resided in real-time computer. and graphic user interface program resided in host computer. The real-time computer consists of six TI C-40 processors connected in parallel. The seeker emulator is designed by using analog circuits coupled with mechanical equipments. The system unit provides interface function to match impedance between the components and processes very small electrical signals. Also real launch unit of missiles is interfaced to simulator through system unit. In order to use the real-time parallel processing simulator developed here as a performance analysis equipment for rolling missiles, we perform verification test through experimental results in the field.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.6
• /
• pp.451-456
• /
• 2018

UAVs (Unmanned Aerial Vehicles) are widely used for maintenance and monitoring of facilities. It is necessary to acquire a high-resolution image for evaluating the appearance state of the facility in safety inspection. In addition, it is essential to acquire the video data in order to acquire data over a wide area rapidly. In general, since video data does not include position information, it is difficult to analyze the actual size of the inspection object quantitatively. In this study, we evaluated the utilization of 3D point cloud data of bridges using a matching between video frames and reference photos. The drones were used to acquire video and photographs. And exterior orientations of the video frames were generated through feature point matching with reference photos. Experimental results showed that the accuracy of the video frame data is similar to that of the reference photos. Furthermore, the point cloud data generated by using video frames represented the shape and size of bridges with usable accuracy. If the stability of the product is verified through the matching test of various conditions in the future, it is expected that the video-based facility modeling and inspection will be effectively conducted.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.17-25
• /
• 2019

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

• Journal of Advanced Navigation Technology
• /
• v.23 no.1
• /
• pp.44-54
• /
• 2019

In many countries, there are needs of new transportations to replace ground congestions due to growing number of cars. In addition, the increase in the number of cars held by economic growth will further increase traffic congestion in the future. To overcome this problem, many researches have been performed for personal air vehicle (PAV). In this study, the wing loading and the power-to-weight ratio that are major design parameters for the sizing of roadable PAVs were calculated for different kinds of airfoil and engine types. I.e., in the sizing process, the study was conducted to determine the design point using the graphs of wing loading, power-to-weight ratio, brake horse power, and fuel efficiency for the given mission profiles considering domestic environments and the FAR PART 23 which is the GA class aircraft certification standard. As a result of sizing, using diesel engine require high maximum take-off weight, wing area, and power compared to gasoline engine due to more engine weight.

• Journal of Advanced Navigation Technology
• /
• v.22 no.2
• /
• pp.111-122
• /
• 2018

At present, the ground transportation system is saturated in many countries including Korea. To overcome this problem, many researches of developing a roadable personal air vehicle (PAV) are being carried out to alleviate traffic congestion and to accomplish door-to-door mobility through three-dimensional traffic system. In this study, the thrust-to-weight ratio, the wing loading, and the power-to-weight ratio that are major design parameters for the sizing of roadable PAVs were calculated under the constraints of ground roll, climb rate, maximum cruise speed, service ceiling, stall speed. Also, in the sizing process, the study was conducted to determine the design point using the graphs of thrust-to-weight ratio, wing loading, power-to-weight ratio, and brake horse power for the mission profiles considering domestic environments and the FAR PART 23 which is the GA class aircraft certification standard.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.7
• /
• pp.539-547
• /
• 2021

Helicopter rotor blade is required to be designed by considering the interacting effects among aerodynamics, flexibility, and controllability. The reverse design allows the structural components to have common characteristics by using the configuration numerics and experimental results. This paper aims to design the composite rotor blade which will feature common characteristics with that of BO-105. The present engineering design procedure is done by dividing the rotor blade into a few sections and composite laminates across the cross section. For each section, variational asymptotic beam sectional analysis (VABS) program is used to evaluate its flapwise, lagwise, and torsion stiffnesses to have discrepancy smaller than certain tolerance. Finally, CAMRAD II is used to predict the stress acting on the rotor blade during the specific flight condition and to check whether the present deign is structurally valid.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.447-456
• /
• 2020

The study area is a slope in Dogye-eup, Samcheok-si, Gangwon-do. The cutting method was applied to this slope for stabilization in 2009 due to the influence of the waste-rock dump located at the top of slope. Recently, soil cracks and creep have occurred on this slope, and the drainage channel was damaged. Therefore, it was analyzed the topography change through photogrammetry using a UAV. Orthophotos were taken in April and October 2019 respectively. From the Orthophots, Digital Surface Model (DSM) was extracted. Time series analysis was performed by comparing each DSM. The topography of October was pushed forward while maintaining the topography of April. Through these features, it is judged that the soil creep is occurring in this study area.

• Journal of the Korea Society for Simulation
• /
• v.29 no.4
• /
• pp.21-31
• /
• 2020

NCTR(Non-Cooperative Target Recognition) refers to the function of radar to identify target on its own without support from other systems such as ELINT(ELectronic INTelligence). ISAR(Inverse Synthetic Aperture Radar) image is one of the representative methods of NCTR, but it is difficult to automatically classify the target without an identification database due to the significant changes in the image depending on the target's maneuver and location. In this study, we discuss how to build an identification database using simulation and deep-learning technique even when actual images are insufficient. To simulate ISAR images changing with various radar operating environment, A model that generates and learns images through the process named 'Perfect scattering image,' 'Lost scattering image' and 'JEM noise added image' is proposed. And the learning outcomes of this model show that not only simulation images of similar shapes but also actual ISAR images that were first entered can be classified.