Proceedings of the Materials Research Society of Korea Conference
/
2012.05a
/
pp.106.2-106.2
/
2012
Ti-Ni합금은 CsCl구조의 B2상, monoclinic 구조의 B19'(M)상과 rhombohedral 구조의 R상(R)이 나타난다고 알려져 있고, 이들 상의 변태에 의해 열탄성 마르텐사이트와 응력유기 마르텐사이트에 의한 형상기억효과와 초탄성 효과를 가지고 있다. 또한 Ti-Ni 합금은 우수한 형상기억특성을 가질 뿐만 아니라 생체적합성, 가공성 및 내식성 등이 뛰어나 공업분야 및 생체분야에서 폭 넓게 활용되고 있다. Ti-Ni합금의 형상기억특성은 냉간가공 후 어닐링 처리의 온도와 시간에 따른 matrix 내 Ni의 농도, 석출물의 밀도와 크기, 전위밀도와 전위주위의 응력장에 의해 영향을 받는다고 알려져 있다. 본 연구에서는 Ti-Ni합금의 형상기억 특성 및 변태온도에 미치는 영향을 조사하기 위해 다양한 냉간가공률의 시료를 제작하여 다양한 온도에서 Annealing 처리를 하여 냉간가공률 및 Annealing 온도가 형상기억특성에 미치는 영향을 조사하였다. Ti-50.4 at.% Ni 합금은 진공 아크 용해로에서 용해 하였으며, 용해된 Ingot는 열간단조 및 열간 압출한 후 냉간 인발과 중간온도에서 어닐링을 반복하면서 직경 0.5mm의 선재로 만들었다. 최종적으로 제작한 선재의 냉간가공률은 9.5%, 18.2%, 34.5%, 45% 이었다. 각 시편은 5X10-5torr의 진공으로 석영관에 진공 봉입하여 각각 673K, 723K, 783K에서 1hr 열처리 하였다. 합금의 형상기억특성과 변태온도는 DSC에 의해 조사되었다. DSC 측정 결과, 냉간가공률이 증가함에 따라 마르텐사이트 변태 온도는 감소하였고, 어닐링 온도가 증가함에 따라 마르텐사이트 변태 온도는 증가하였다. 또한 가공률이 증가하여도 R상 변태온도는 큰 변화가 없었고, Annealing온도가 증가함에 따라 R상 변태온도는 감소하였다. 또한, 형상기억특성은 인장시험기를 이용한 정하중 열싸이클 테스트를 이용하여 평가 하였다. 냉간 가공률이 증가함에 따라 안정한 형상기억특성을 나타내었다.
Proceedings of the Korean Radioactive Waste Society Conference
/
2003.11a
/
pp.373-378
/
2003
As a part of assessment of the structural material for the molten salt handling system, corrosion behavior of austenitic alloys, Fe-base and Ni-base in the molten salt of $LiCl-Li_2O_2$ was investigated in the range of temperature; 650~$725^{\circ}C$, time; 24- 168h, $Li_2O$; 3wt%, mixed gas; Ar-10%$O_2$. In the molten salt of $LiCl-Li_2O_2$, Ni-base alloys showed higher corrosion resistance than Fe-base alloys. Fe-base alloy with low Fe and high Ni contents exhibited better corrosion resistance. The scales of $Cr_2O_3$, $FeCr_2O_4$ on Fe-base alloys were showed, and $Cr_2O_3$, $NiFe_2O_4$ on Ni-base alloys were also showed.
The oxidation behavior of Ag-36.8a%Cu-7.4at%Ti alloy brazed on Si3N4 substrate was investigated at 400, 500 and 600$^{\circ}C$ in air. Under this experimental condition Si3N4 and Ag were not oxidized whereas Cu and Ti among the brazing alloy components were oxidizied obeying the parabolic oxidation rate law. The activation energy of oxidation was found to be 80kj/ mol which was smaller than that of pure Cu owing to the presence of oxygen active element of Ti. The outer oxide scale formed from the initial oxidation state was always composed of Cu oxides which were known to be growing by the outward diffusion of Cu ions. As the oxidation progressed the concentration gradient occurred due to the continuous consumption of Cu as Cu oxides and consequently build-up of an Ag-enriched layer below the Cu oxides resulted in the formation of multiple oxide scales composed of Cu oxide (CuO) /Ag-enriched layer/Cu oxide (Cu2O) /Ag-enriched layer. Also the inward diffusing of oxygen through Cu oxide and Ag-enriched layers led to the formation of internal oxides of TiO2.
Journal of the Korean Society of Marine Environment & Safety
/
v.19
no.5
/
pp.538-544
/
2013
In this study, cavitation characteristics of a thermal spray coating were evaluated in order to improve durability and cavitation resistance. For a coating material, a Ni-based self-fluxing alloy was thermal-sprayed over a ALBC3 alloy substrate and subsequently modified by heat treatment.The resulted self-fluxing coating layer had relatively high hardness compared to the base material, and thus would be expected to exhibit good durability. However, the cavitation characteristics were deteriorated due to the intrinsic porous structure of the coating. Therefore, it is essential to optimize heat treatment condition during thermal spraying coating process for self-fluxing alloy, and in this research the increase in heat treatment temperature is thought to increase the fluidity of B and Si in the self-fluxing alloy and to remove pores or defects, leading to the characteristics enhancement.
Ha, Yong-Soo;Kim, Chul-Soo;Kang, Chung-Yun;Kim, Il-Soo;Cho, Chang-Hyun
Korean Journal of Materials Research
/
v.8
no.8
/
pp.672-677
/
1998
The following work examines the growth rate and microstructure of the $AI_2O_3$-composite formation by melt oxdation of pentad AI-alloys. The I weight % of each metal elements Cu and Ni were added to AI-IMg-3Si-3Zn and AI-IMg- 3Si-5Zn alloys. The diffenent pentad AI-alloys were oxidized 20 hours long at 1373K and 1473K. The oxidation rates were determined by observing the weight gain. The macro- and microstructure of formed oxide layer were examined by optical microscopy. The AI-IMg-3Si-5Zn-lCu alloy revealed the best oxidation behavior, but formedoxide layer was inhomogeneous.The oxidation rate were accelerated, and the uniform growth of the oxide layer with fine microstructure were obtained by putting a thin layer of $SiO_2$ on the surface of the alloy.
Kim, Won-Baek;Lee, Cheol-Gyeong;Lee, Jae-Cheon;Seo, Chang-Yeol
Korean Journal of Materials Research
/
v.8
no.10
/
pp.898-904
/
1998
Ni-W alloys containing 10 to 50wt% W were prepared by electrodeposition. Tungsten content in the alloy increased with current density. X-ray diffraction analysis revealed that the alloy was crystalline phase when deposited at current densities lower than 50mA/${cm}^2$. Their crystal structure transformed to amorphous at higher current densities. In terms of tungsten content, the crystal -+ amorphous transition occurred at 40-46wt% which was identified by the 3 fold increase in the width of a diffraction peak. The lattice parameter of crystalline phase increased with W upto 40wt% which is higher than the solubility limit of W (about 30wt%) in Ni. Therefore, the alloys are considered to be Ni solid solution supersaturated with W. The amorphous Ni-W alloys were recrystallized by annealing them at temperatures over $400^{\circ}C$. This was evidenced by the appearance a strong [ 11 11 annealing texture. The supersaturated W was precipitated during the annealing at over $800^{\circ}C$. The current-density dependence of W content and crystallinity was utilized to produce alternating layers of crystalline (30wt% W) and amorphous (50wt%) phases which may exhibit unique mechanical and corrosion properties.
Proceedings of the Korean Vacuum Society Conference
/
2010.02a
/
pp.237-237
/
2010
에너지소비와 엔진 부품의 마모문제를 해결하기 위해, soft-phase를 doping한 hard상의 coating에 대한 실험이 최근 중요한 연구 테마로서 진행 중이다. 특히 MoN-Cu coating은 미국 Argon 연구소의 Erdemer박사 등에 의해, 고온 및 상온 윤활성이 우수한 코팅층으로 보고된 이후 많은 연구가 진행되고 있다. 그러나 기존 연구는 Mo와 Cu의 원소타겟을 이용한 연구가 주력이 되었다. 높은 경도와 저온 고온에서의 낮은 나노 혼합물 코팅 종류는 일반적으로 Mo와 Cu와 같은 원소 합금을 이용한 다수 타겟을 이용한 공정에 의해 진행되어왔다. 이러한 복수의 타겟에 의해 증착 동안에는, 정확한 조성, 큰 크기의 시편들의 균일 증착을 조절하기가 쉽지 않다. 또한, 코팅층에 3번째 성분을 추가하기가 어렵다는 문제점이 있다. 본 연구에서는, 최상의 마찰계수와 표면경도를 보이는 MoN-Cu층을 형성시키기 위하여 합금으로 단일 타겟을 제조하였다. 이를 위한 최적 조성을 결정하기 위하여 Mo, Cu 단일 타겟을 이용한 Unbalanced Magnetron sputtering 법으로 다양한 Cu 함량의 MoN+Cu 합금을 제조하였으며, 이에 대한 경도 및 마찰계수 측정을 통해 최적의 Cu 함량을 결정하였다. 이러한 최적 조성의 Cu 타겟제조를 기계적 합금화와 Spark plasma sintering 기술을 이용하여 제작하였으며, 복수의 합금 타겟과 단일 합금 타겟으로 제조된 코팅층의 물성 비교를 통해 합금 타겟의 우수성 여부를 확인하고자 하였다. 증착된 두 조건의 물성을 비교 단일 타겟은 두가지 타겟으로 증착한 것보다 비슷한 조성에서 경도가 높았으며 경도가 비슷한 조성에서는 마찰계수가 낮았다. 또 입자는 10 at.% Cu 조성에 대해 단일타겟이 50nm 결정립을 갖는 반해 단일타겟은 측정이 불가능할 정도의 미세한 결정립을 가졌다. Erdemir의 연구 결과에 의하면, Cu 함량이 증가함에 따라 columnar 형태의 코팅층구조가 나노 구조로 변한다고 하였는데, 본 연구에서 복수의 원소 타겟에서는 확인이 안되었으며, 단일 합금 타겟에서 완벽한 featurless 형태의 코팅층 구조와 우수한 조도의 박막층을 얻을 수 있었다. 이렇게 제조된 다양한 코팅층에 대한 마찰계수 측정이 진행중이다.
In this study, the electroless deposition of Co-B and Co-W-B alloy thin films was developed and the effect of B and W contents on the hardness of the alloy thin films were investigated. An amorphous Co alloy film was successfully formed by electroless deposition and the contents of B and W in the film were controlled by varying the concentrations of dimethylamine borane and sodium tungstate dihydrate, which were used as a reducing agent and W source, respectively. The hardness of the thin films increased as the contents of B and W were increased because B and W act as impurities suppressing the propagation of dislocation in a film. In addition, it was found that the content of B and W in the Co alloy films can be increased significantly when aeration is not performed. Finally, the hardness of Co-W-B alloy thin film was improved up to 8.9 (${\pm}0.3$) GPa.
Kim, Jeong-Min;Jung, Ki-Chae;Kim, Chae-Young;Shin, Je-sik
Journal of Korea Foundry Society
/
v.41
no.1
/
pp.3-10
/
2021
In the compound casting between the aluminum alloy and the cast iron, the iron component may be dissolved from the cast iron during the process and mixed into the aluminum melt, thereby forming various iron-containing intermetallic compounds and significantly deteriorating the tensile properties of the aluminum alloy. On the other hand, unlike Fe, which is added as an impurity, Cu is added to improve the mechanical properties of the aluminum alloy. In this study, the change in microstructure and tensile properties of aluminum alloys due to the addition of Fe and Cu was investigated. A large amount of iron-containing compounds such as coarse Al5FeSi phases were formed when the iron content was 1% or more, and the tensile properties were significantly reduced. In the case of the aluminum alloy to which Cu was added, an Al2Cu phase was additionally formed and the tensile strength was clearly improved.
Eco-friendly magnesium-air battery is a kind of metal-air battery known as a primary battery with a very high theoretical discharge capacity. This battery is also called a metal-fuel cell from the viewpoint of using oxygen in the atmosphere as a cathode active material and magnesium alloy as a fuel. Since battery performance is determined by the properties of the magnesium alloy used as a anode, more research and development of the magnesium alloy electrode as a anode material are required in order to commercialize it as a high-performance battery. In this study, the commercialized magnesium alloys(AZ31, AZ61) were selected and then electrochemical measurements and discharge test were conducted. Electrochemical properties of magnesium alloys were investigated by OCP changes, Tafel parameters and CV measurement, and the feasibilities of AZ61 alloy with excellent discharge capacity(1410mAhg-1) as electrode materials were evaluated through CC discharge experiments.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.