• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 춘계학술발표회 초록집
• /
• pp.62-62
• /
• 2006

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.117-118
• /
• 2009

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2008년도 추계학술발표대회 및 제15회 신소재 심포지엄
• /
• pp.39.1-39.1
• /
• 2008

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.357-364
• /
• 2004

합금화용융아연도금강판(GA)은 가격이 저렴하고 내식성 및 용접성이 우수하여 최근 자동차용강판으로 그 사용량이 급격하게 증가하고 있으나 도금밀착성이 나쁘고 프레스성형이 떨어지는 단점을 가지고 있다. 본 연구에서는 GA 도금층에 여러가지 유,무기계 윤활처리를 실시하여 이것이 마찰특성은 물론 용접성, 도장성 및 내식성에 미치는 영향을 평가하였다. 유기계 윤활피막은 가공성과 도금 밀착성에서 유리하나 용접성과 탈지성에서는 불리하였고, 무기계 윤활피막인 Prephosphate 및 금속윤활처리 강판은 가공성에서는 유기윤활피막 보다 약간 떨어지나 용접성과 탈지성에서는 우수한 결과를 나타냈다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.191-191
• /
• 2013

최근 차량 경량화와 승객의 안전성을 위하여 고성형/고강도강의 수요가 급격히 증가하고, 이를 위한 강종 개발로 고강도 및 고버링성 소재가 개발되고 있으며, 또한 차량의 자동차의 사용환경이 점차 가혹해지고 장수명화 됨에 따라 자동차 강판에서 방청방식의 중요성이 크게 대두되고 있어, 이를 충족시키기 위한 합금화융융아연도금 열연강판(HGA)의 사용이 증대되고 있다. 따라서 본 연구는 고강도/고버링성의 합금화용융도금열연강판 개발을 목적으로 하였으며, 합금 성분 및 PGL의 열처리 조건에 따른 기계적 물성 을 평가하였으며, SEM,OM등을 통한 미세조직 관찰 및 홀확장성 평가를 실시 하였다.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.109-115
• /
• 2006

This paper is designed to estimate friction and powdering characteristic of coating layer on galvannealed sheet steel with different annealing temperature, which is 465, 505, 515 and $540^{\circ}C$, Estimations of powdering and friction were done using a $60^{\circ}$ bending test and one side friction test, respectively. In order to obviously understand the effect of coatings on friction cross-section of coatings before and after friction test was also observed by SEM. The results show that powdering of coatings is increased with increasing of annealing temperature and that friction characteristic greatly depends on powdering which leads to increase of real contact area between tools and coatings.

• 대한기계학회논문집A
• /
• 제33권6호
• /
• pp.560-567
• /
• 2009

This paper was designed to estimate the adhesion strength of galvannealed coatings on steel sheets. The adhesion strength were evaluated using single lap - shear tests where the lap joint was bonded by structural adhesive. Tests were performed for overlap length of 5mm, 10mm and 15 mm and three directions (0, 45, 90) of steel sheets used as the adherend of the overlap joint. After the tests, FE simulations of the single lap-shear test were also carried out to observe the stress distribution in the interface between the adhesive and the coated sheet. The results showed that the joint failure loads obtained from the tensile tests of bonded single lap-joints were the same, regardless of overlap lengths and directions of steel sheets. Also, the failure of galvannealed coatings greatly depended on shear stress distribution in the interface and the value was about 30MPa.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.238-243
• /
• 2007

This paper is designed to estimate the adhesion strength of coating layer on galvannealed steel sheet using lap shear test. The single lap shear test is the most commonly used standard test for determining the strength of medium-strength and high strength bonds. The bond strength of bonded single lap joints on subjecting the substrates to loads is determined by lap shear forces in the direction of the bonded joint. In this study, specimen for adhesion strength test was made to attach coated sheet to cold rolled sheet and were heated in temperature of 180 for 20minutes. After test, detached parts of coatings on coated sheet were observed using SEM and EDX to identify substrate and complete detachment. The tested results showed that adhesive strength of coating is unrelated to anisotropy of sheet and is difficult to be extracted using conventional theory because of fine cracks of coating layers which were created during annealing process.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.176-184
• /
• 2003

New lubricant film of organic and inorganic composite resin was developed to improve the press formability of galvannealed steel sheets (GA) for automotive body panels. The frictional coefficient of lubricant GA steel sheets is about 20% superior to that of uncoated GA. The current range of spot welding of lubricant GA is similar to that of the uncoated GA, but the burning trace of spot welding is inferior to that of the uncoated GA in the oiling condition. The alkaline degreasability of lubricant GA shows 100% in alkaline degreasing condition of automotive company. The size and shape of the phosphated coating layer are similar to those of the uncoated GA sheet. The powdering property of the lubricant GA gives rise to 20∼50% improved property compared with the uncoated GA sheet.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 춘계학술발표회 초록집
• /
• pp.31-32
• /
• 2003

In the Present study, the effect of galvannealing conditions on the phase distribution of the Zn-Fe intermetallic phases in the coating layer of the galvannealed steel sheets(GA) was investigated in an interstitial free steel and two kinds of high strength steels. The composition profiles of the coating layers were analyzed using AA and EDS analysis, and the distribution of the intermetallic phases was examined with the aids of X-ray diffraction. On the basis of the pole figure and OIM analyses, it was clarified that the preferred orientation of the $\zeta$ phase depended on the development of the $\gamma$-fibre texture in the substrate.