• The Journal of the Petrological Society of Korea
• /
• v.10 no.3
• /
• pp.179-189
• /
• 2001

The determination of trace concentration of U, Th and Pb was carried out for chemical dating of zircon and monazite by electron microprobe. Detection limit and error range should be considered to measure characteristic X-rays of M-line from those minerals, which are low in the ionization of atom and low peak intensity in the spectrum. The element of U, Th and Pb were simultaneously measured with 3 spectrometers equipped with PET crystal to reduce a total counting time and error due to drift of instrumental operating condition. Detection limit could be improved from increase of the peak/background ratio through adjusting pulse height analyzer about 1000 mv baseline. Under permissible maximum analytical conditions, theoretical detection limit of U, Th and Pb is down to 30 ppm (99% confidence level). The analytical result was maintained at a relative error $\pm$10% ($2{\sigma}$) in 800 ppm Pb, $\pm$5% ($2{\sigma}$) in 2330 ppm U and $\pm$10% ($2{\sigma}$) in dating from a single measurement of zircon at 15 keV and 100 nA. However, for the precise dating of zircon and monazite, if it is considered a 3 $\mu\textrm{m}$ spatial resolution, <100 ppm ($3{\sigma}$) detection limit and <$\pm$10% ($2{\sigma}$) relative error, optimum analytical conditions are given as 15~20 keV accelerating voltage, 100~200 nA beam current and 300~1200 sec total counting time. To reduce material damage by high current, there is need to be up to 3~5 $\mu\textrm{m}$ of electron beam diameter, or to use arithmetic average of multiple measuring at a shorter counting time. A younger or relatively low concentration rocks can be dated chemically by lower detection limit and improved precision resulted from increase of current and measuring time.

• Analytical Science and Technology
• /
• v.14 no.2
• /
• pp.180-190
• /
• 2001

Oder-active compounds are complex in a sample. These compounds are usually analyzed by GC or GC/MSD while such analytical measurement can quantify specific volatile organic compounds, it has limitations in identifying odor-active compounds. To resolve this problem, GC-Sniffing or GC-Olfactometry method has been attempted. In this study, GC/FID/Olfactometry system was developed. This system can simultaneously sniff and detect GC effluents by traditional GC combined with human olfactory system. The time gap between FID and ODP response was dependent on the kinds and concentrations of chemicals and panels, with more volatile, stronger and shorten breath cycle panel showing narrow time gap. Thus, clear relationship between FID and ODP should be considered to identify the odor-active compounds.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.39.1-39.1
• /
• 2011

가압경수로의 압력경계기기는 약 $300^{\circ}C$, 150기압의 고온고압수환경에서 가동되고 있다. 특히 가압기 밀림관은 고온수와, 저온수가 교차하는 부분으로 열성층 형성으로 열적, 기계적 피로 및 수화학환경이 더해진 부식피로 등에 의하여 손상을 받는다. PWR 원전에서 수화학환경은 대표적으로 용존산소(DO) 5ppb, pH 6~8, 용존수소(DH) <30 cc/kg, 온도 $316^{\circ}C$의 환경을 유지하게 된다. 가압기 밀림관에는 오스테나이트계 스테인리스강이 사용되는데, 오스테나이트계 스테인리스강은 고온 수화학환경에 민감한 것으로 알려져 있다. 따라서 오스테나이트계 스테인리강을 공기중에서의 기계적특성 및 피로특성을 향상시키기 위하여 질소를 첨가한 스테인리스강을 제조하여 PWR 원전환경에서의 피로균열성장특성을 평가하였다. 실험에 사용된 재료는 PWR 원전 가압기 밀림관 소재인 Type 347 스테인리스강에 0.0005 wt%가 첨가된 상용재와 0.11 wt% 질소가 첨가된 재료이다. 사용된 시편형상은 두께 5 mm, 폭 25.4 mm의 CT 시편이다. 수화학환경은 150기압, 온도 $316^{\circ}C$, 용존산소(DO) 5ppb, 용존수소(DH) 30 cc/Kg, pH는 약 7로 유지 하였으며, 응력비 0.1, 하중 반복속도 10Hz의 기계적 조건에서 하중제어로 시험을 진행하였다. 균열길이는 직류전위차법(Direct Current Potential Drop: DCPD)을 이용하여 측정하였다. 질소함량이 증가할수록 동일 사이클에서 균열길이가 늦게 성장하였고, 피로균열성장속도도 약간 늦어지는 것으로 나타났다. 각 스테인리스강의 피로파면 관찰결과 상용재는 약 1 ${\mu}m$의 산화물들이 생성되는 반면 질소첨가 스테인리스강은 약 0.1 ${\mu}m$정도 산화물이 생성되었다. 산화막의 두께도 질소가 첨가됨으로써 상용재에 비해 얇게 생성되었다. 따라서 질소가 첨가됨으로써 부식환경에서 내산화성이 향상되었으며, 이는 피로균열성장특성에 영향을 미치는 것으로 판단된다.

• Korean Journal of Food Science and Technology
• /
• v.48 no.4
• /
• pp.366-371
• /
• 2016

This study was carried out to evaluate the feasibility of using domestic wheat flour as ingredient of pizza dough by examining the physicochemical and sensory properties of the dough. Five pizza dough samples were prepared with different ratio of domestic and imported wheat flour. Significant differences were observed in crude protein content, crude ash content, and color of the pizza dough samples; however, no significant difference was found in mechanically measured rheology. A sensory evaluation based on 23 descriptive attributes indicated significant differences between pizza dough made from domestic wheat flour and that made from imported wheat flour for springiness and softness of the surface, roughness, and chewiness (p<0.05). Principal component analysis showed that the greater amount of Korean wheat flour in the dough resulted in different values from negative to positive ends of principal component 1 (37.4%).

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1061-1066
• /
• 1998

The synthesises of anion exchange resin from 4vinylpyridine-divinyIbenzene(4-VP-DVB) were intented to separate boron ion. The heterogeneous anion exchange membranes were prepared with polyethylene(PE) matrix bythe hot press method. The prepared exchange membranes were characterized by FT-IR, conductormeter and pH meter to confirm structural, mechanical and electrochemical properties. Their capacities were measured by changing floe rate and voltage. The best seperation capacity was appeared in the heterogeneous membrane which contains 50 wt % 4-VP-DVB resin within PE matrix. The heterogeneous membranes treated with acid were better than that treated with water. Results from this experiment were indicated that the optimal flow rate, voltage. and time in the seperation of boron ion were lOml/min, 18volts, and 4 hours respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.12.2-12.2
• /
• 2009

전자 디스플레이 산업의 중요성과 미래사회에서 요구되는 정보기기로써 유연한 기판을 사용한 소자에 대한 수요가 급격히 증가하고 있으며, 이들 산업에 응용되기 위해서는 저비용, 고생산 공정이 요구되고 있다. 이를 위해 인쇄전자 기술에 대한 연구가 활발히 진행되고 있다. 특히, 금속배선은 모든 소자의 기본이면서 낮은 저항과 높은 신뢰성을 동시에 요구하고 있어 인쇄전자 기술이 해결해야 할 가장 어려운 난제 중의 하나이다. 따라서 본 연구에서는 낮은 저항과 높은 신뢰성을 만족시킬 수 있는 새로운 금속배선 공정으로서 폴리이미드 필름을 초발수 처리한 후 친수 패턴을 하여 전도성 잉크에 함침함으로서 친수 패턴을 따라 금속배선이 이루어 지도록 하는 방법을 제안하고자 한다. 폴리이미드 필름의 표면을 플라즈마 처리하여 표면에 나노돌기를 형성시키고 불소기를 함유한 코팅층을 형성시킴으로써 물에 대한 접촉각이 $150^{\circ}$이상이 되도록 초발수 처리할 수 있었다. 초발수 처리된 폴리이미드 기판에 쉐도우 마스크를 사용하여 UV조사함으로써 조사된 부분만 친수성을 가지는 패턴을 형성하였다. 이렇게 친수 패턴이 제작된 초발수 폴리이미드 유연기판을 실버잉크에 함침함으로써 선폭 $200{\mu}m$를 가지는 금속배선을 형성시켰다. 형성된 금속배선의 단면 형상을 측정하였으며, 열처리를 통하여 비저항이 $30{\mu}{\Omega}$-cm를 얻을 수 있었다. 통상 1회의 함침으로는 금속배선의 두께가 150nm정도로 금속배선으로 사용하기에는 얇아 배선의 두께를 증가시키기 위하여 수 회 함침을 시도하여 $2{\mu}m$의 두께로 증가시킬 수 있었다. 이때 선폭과 선간 간격은 크게 변하지 않고 두께만 증가시킬 수 있었다. 이는 금속배선을 형성한 후에도 폴리이미드 유연기판의 초발수성은 그대로 유지되어 여러번 함침할 때 잉크가 이미 형성된 배선에만 묻게 되어 두께는 증가하나 선폭과 선간 간격은 증가하지 않는 것으로 판단된다. 사용한 실버잉크는 실버의 함량은 10~20wt%인 수계 잉크였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.234-243
• /
• 2023

The electromagnetic pulse(EMP) is a general term for high-output electromagnetic waves, and is classified into EMP generated from nuclear weapons, non-nuclear EMP, and EMP generated by natural phenomena. Electromagnetic pulses are means that can cause fatal damage to all electronic devices with electromagnetic elements, such as communication devices, mobile phones, computers, TVs, and means of transportation. In this study, the electromagnetic pulse(EMP) shielding effectiveness evaluation of paints according to the type and amount of carbon material was conducted to develop EMP shielding inorganic paint using carbon materials. In order to analyze the improvement of compatibility and dispersibility between materials, experiments were conducted two times with about 27 types of mixture proportions, and the electromagnetic pulse shielding effectiveness was evaluated by the electrical resistance measurement method. As a result of applying the EMP shielding paint developed through this study to shielding concrete, it was confirmed that the shielding performance was improved from about 25 dB to a maximum of 40 dB.

• The Korean Journal of Mycology
• /
• v.29 no.1
• /
• pp.15-21
• /
• 2001

This study was conducted to investigate the immunomodulatory activities of proteoglycan extracted from cultured mycelia of Ganoderma lucidum IY009. The proteoglycan contained two polymer peaks, one was the higher MW peak of 2,000 kD and the other was low peaks of 12kD. To understand the part of strong pharmaceutical activity between two peak, the proteoglycan was separated by ultrafiltration and column chromatography and then examined the various pharmaceutical effects. High molecular weight fraction possesing high content of ${\beta}-linked$ glucan was exhibited high antitumor activity, against sarcoma 180 bearing ICR mouse. And also, anticomplementary activity was highly observed in high molecule fraction than low it fraction. When the raw 264.7 and murine peritoneal macrophage treated with low fraction, high fraction and other stimuli. The activities inducing tumor necrosis factor of the high factions were $2.2{\sim}2.5$ times stronger than that of low fraction.

• Archives of design research
• /
• v.19 no.1 s.63
• /
• pp.201-214
• /
• 2006

Modern society is an age of vagueness and confusion. In addition, vagueness, complexity and variety are seen throughout art including modern philosophy, literature, and environmental design. A phenomenon like this shows that modern society has integrated different components as an organic relationship frequently crossing the boundary of fields. This feature can be regarded as hybrid related with accepting contradictory components and binding them into one under relationship between part and whole. As new design concept, presented are attitude to accept the two instead of attitude to select one of the alternatives, abundance instead of dearness, and ambiguity instead of simplicity. This principle has a crucial influence on creative design providing opposing contradiction and several alternative plans as non-deterministic form not completed one and, above all, useful information in mutual dependence and mutual relationship. When it comes to hybrid, therefore, a strategy is needed to consider layer of several fields getting out of standardizing space into a single space. As an event of this situation and concept, space experience means behaving freely based on experience of users' body. It can be known that this experience brings about users' more dynamic experience in comparison with the experience of seeing environmental design from a viewpoint of visual ism on the existing simplicity. Such a practical experience is subjective, synesthetic, and non-observational one. Therefore, hybrid has brought active users to the stage, which is distinguished from synesthesia felt through body's experience, not through observational attitude and visual space which achieve former balance and harmony with non-determination. That's because hybrid creatures are turning to a product resulted from creative imagination instead of from reappearance which makes text visualized. Such experience performed by user's active participation collapses the boundary between special elite-centered art and daily life and it is the present progressive form showing creation process of future events and new esthetic experience.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.205-209
• /
• 2014

Medical polymers require sterilization and must be able to maintain material properties for a specified shelf life. Sterilization can be achieved by using gamma or e-beam exposure. In this study, accelerated aging tests of poly(ether-block-amide) (PEBA) copolymer samples is presented. PEBA copolymer samples with different polyether content that result in Shore hardness of 35D to 72D, were sterilized using e-beam radiation followed by accelerated aging at $55^{\circ}C$. E-beam sterilization effect on molecular weight and mechanical property has performed and analyzed. The average molecular weight significantly reduced as a result of ageing. The enlarged proportion of low molecular weight chains in the aged samples is consistent with the generation of degradation products produced by oxidative chain scission. Also E-beam materials have shown decreased tensile strength and elongation. Overall, this study demonstrated that the medical grade PEBA was significantly affected by radiation exposure over aging time, particularly at high irradiation doses. For medical use in case of radiation sterilization required, it is recommended to avoid Pebax material. If Pebax material must be in use for medical device, recommend to use alternate sterilization method such as Ethylene Oxide sterilization.