• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.190-196
• /
• 2001

The microwave dielectric properties and a sintering behavior of MgTiO$_3$-CaTiO$_3$ ceramics doped with Li were investigated. The main composition was fixed as 0.94MMgTiO$_3$-0.06CaTiO$_3$ and Li$_2$CO$_3$was added excessively in the range of 0~10 mol% (with reference to Li atoms) and the specimens were sintered at 1200~140$0^{\circ}C$ for 4 hours. When the amount of Li was small the quality factor and dielectric constant were reduced, while those tow properties increased if the Li amount was above 1 mol%. But if Li was overly added those dielectric properties decreased again. Li, if added in the composition range of 1.0~3.0 mol%, can increase the quality factor of MgTiO$_3$-CaTiO$_3$ ceramics. The optimum amount of Li was 1.5mol% and sinterign condition was 1275$^{\circ}C$/4hr, at which we cudl obtain following results ; dielectric constant ($\varepsilon$$_{r}$) of f20.0, quality factor(Qxf$_{0}$) of 78,000 GHz and temperature coefficient of resonant frequency($\tau$$_{f}$) of -1.6 ppm/$^{\circ}C$.>.>.>.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1100-1106
• /
• 2004

In this paper, we intend to make fringe-field switching (FFS) mode cell by the ion beam (IB) alignment method on the a-C：H thin film, to analyze electro-optical characteristics in this cell. We studied on the suitable inorganic thin film for fringe-field switching (FFS) cell and the aligning capabilities of nematic liquid crystal (NLC) using the alignment material of a-C：H thin film as working gas at 30 W rf bias condition. A high pretilt angle of about 5 $^{\circ}C$ by ion beam (IB) exposure on the a-C：H thin film surface was measured. Consequently, the high pretilt angle and the good thermal stability of LC alignment by the IB alignment method on the a-C：H thin film surface as working gas at 30 W rf bias condition can be achieved. An excellent voltage-transmittance (V -T) and response time curve of the IE-aligned FFS-LCD was observed with oblique IB exposure on the a-C：H thin films. Also, AC V-T hysteresis characteristics of the IB-aligned FFS-LCD with IE exposure on the a-C：H thin films is almost the same as that of the rubbing-aligned FFS cell on a polyimide (PI) surface.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.10 s.340
• /
• pp.55-64
• /
• 2005

In this paper, we designed floating point units to accelate real-time 3D Graphics for Geometry processing. Designed floating point units support IEEE-754 single precision format and we confirmed 100 MHz performance of floating point add/mul unit, 120 MHz performance of floating point NR inverse division unit, 200 MHz performance of floating point power unit, 120 MHz performance of floating point inverse square root unit at Xilinx-vertex2. Also, using floating point units, designed Geometry processor and confirmed 3D Graphics data processing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.398-398
• /
• 2007

The Liquid Crystal (LC) alignment uniformity is very important in LC devices. The alignment mechanism of LC molecules on a rubbed polyimide (PI) surface is very important for both LC fundamental research and application. So, Generally a rubbing method to align LC has been widely used to mass-produce LCD panels. But because rubbing method is contact method between rubbing fabric and indium-tin-oxide glass or flexible substrate, rubbing method has some defects, such as the electrode charges and the creation of contaminating particles. Thus we strongly recommend a non-contact alignment technique for getting rid of some defects of rubbing method. Most recently, the LC aligning capabilities achieved by ion-beam exposure on the organic and nonorganic thin film surface have been reported successfully. In this research, we studied the tilt angle generation and electro-optical performances for a NLC on homeotropic polyimide surfaces with ion-beam exposure. The LC aligning capabilities of a nematic liquid crystal (NLC) on a homeotropic PI surface using a new ion-beam method were studied. On the homeotropic PI surface, the tilt angle of the NLC by exposure ion-beam had a tendency to decrease as increased ion-beam energy density. And, on the homeotropic PI surface, the alignment character of the NLC with respect to ion-beam energy was good. And we achieved satisfactory result for EO character.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.370-370
• /
• 2007

The liquid crystal (LC) aligning capabilities treated on the Organic overcoat thin film surfaces by ion beam irradiation and rubbing method was successfully studied for the first time. The Organic overcoat layer was coated by spin-coating. In order to characterize the LC alignment, the microscope, pretilt angle, thermal stress, and atomic force microscopy (AFM) image was used. The good LC aligning capabilities treated on the Organic overcoat thin film surfaces with ion beam exposure of $45^{\circ}$ above ion beam energy density of 1200 eV can be achieved. But, the alignment of defect of NLC on the Organicovercoat surface at low energy density of 600 eV was measured. The pretilt angle of NLC on the Organic overcoat thin film surface with ion beam exposure of $45^{\circ}$ for 1 min at energy density of 1800eV was measured about 1.13 degree. But, low pretilt angles of NLC on the Organic overcoat thin film surface with ion beam exposure at energy density of 600, 1200, 2400, and 3000 eV was measured. Also, the pretilt angle of NLC on the rubbed Organic overcoat thin film surfaces was measured about 0.04 degrees. Finally, the good thermal stability of LC alignment on the Organic overcoat thin film surface with ion beam exposure of $45^{\circ}$ for 1 min can be measured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.56-57
• /
• 2006

In this paper, the inorganic multi-layer thin film encapsulation was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam, Sputter, inorganic multi-layer thin-film encapsulation was deposited onto the Ethylene Terephthalate(PET) and their interface properties between inorganic and organic layer were investigated. In this investigation, the SiON SiO2 and parylene layer showed the most suitable properties. Under these conditions, the WVTR for PET can be reduced from a level of $0.57\;g/m^2/day$ (bare subtrate) to 1*10-5 g/$m^2$/day after application of a SiON and SiO2 layer. These results indicates that the PET/SiO2/SiON/Parylene barrier coatings have high potential for flexible organic light-emitting diode(OLED) applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.467-468
• /
• 2006

We report on the fabrication of P3HT-based thin-film transistors (TFT) that consist of indium-zinc-oxide (IZO), PVP (poly-vinyl phenol), and Ni for the source-drain (S/D) electrode, gate dielectric, and gate electrode, respectively. The IZO S/D electrodes of which the work function is well matched to that of P3HT were deposited on a P3HT channel by thermal evaporation of IZO and showed a moderately low but still effective transmittance of ~25% in the visible range along with a good sheet resistance of ${\sim}60{\Omega}/{\square}$. The maximum saturation current of our P3HT-based TFT was about $15{\mu}A$ at a gate bias of -40V showing a high field effect mobility of $0.05cm^2/Vs$ in the dark, and the on/off current ratio of our TFT was about $5{\times}10^5$. It is concluded that jointly adopting IZO for the S/D electrode and PVP for gate dielectric realizes a high-quality P3HT-based TFT.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.398-398
• /
• 2007

Most recently, the Liquid Crystal (LC) aligning capabilities achieved by ion beam exposure on the diamond-like carbon (DLC) thin film layer have been successfully studied. The DLC thin films have a high mechanical hardness, a high electrical resistance, optical transparency and chemical inertness. Nitrogen doped Diamond Like Carbon (NDLC) thin films exhibit properties similar to those of the DLC films and better thermal stability than the DLC films because C:N bonding in the NDLC film is stronger against thermal stress than C:H bonding in the DLC thin films. Moreover, our research group has already studied ion beam alignment method using the NDLC thin films. The nematic liquid crystal (NLC) alignment effects treated on the SiNx thin film layers using ion beam irradiation for three kinds of N rations was successfully studied for the first time. The SiNx thin film was deposited by plasma-enhanced chemical vapor deposition (PECVD) and used three kinds of N rations. In order to characterize the films, the atomic force microscopy (AFM) image was observed. The good LC aligning capabilities treated on the SiNx thin film with ion beam exposure for all N rations can be achieved. The low pretilt angles for a NLC treated on the SiNx thin film with ion beam irradiation were measure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1054-1057
• /
• 2004

The nitrogenated diamond-like carbon (NDLC) exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) films. These diamond-like transparent properties in NDLC come in a material consisting of $sp^2$-bonded carbon versus the $sp^3$-carbon of DLC. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. Liquid crystal (LC) alignment capabilities with ion beam exposure on NDLC thin films and electro-optical (EO) performances of the ion-beam-aligned twisted nematic liquid crystal display (TN-LCD) with oblique ion beam exposure on the NDLC thin film surface were studied. An excellent uniform alignment of the nematic liquid crystal (NLC) alignment with the ion beam exposure on the NDLC thin films was observed. In addition, it can be achieved that the good EO properties of the ion-beam-aligned TN-LCD. Finally, we will present the residual DC property of the ion-beam-aligned TN-LCD on the NDLC thin film surface.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.11
• /
• pp.47-54
• /
• 2015

The number of users of SNS such as Twitter and Facebook increases due to the development of internet and the spread of supply of mobile devices such as smart phone. Moreover, there are also an increasing number of content pollution problems that pollute SNS by posting a product advertisement, defamatory comment and adult contents, and so on. This paper proposes an improved method of extracting the feature of content polluter for detecting a content polluter in SNS. In particular, this paper presents a method of extracting the feature of content polluter on the basis of incremental approach that considers only increment in data, not batch processing system of entire data in order to efficiently extract the feature value of new user data at the stage of predicting and classifying a content polluter. And it comparatively assesses whether the proposed method maintains classification accuracy and improves time efficiency in comparison with batch processing method through experiment.