• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.6
• /
• pp.36-42
• /
• 2010

In this study, the deformation and stress are analyzed through modal and harmonic response analysis at resonance on leaf spring. The displacement range of 7 to 14 mm is shown at natural frequencies as 6 kinds of resonance modes. The maximum deformation is shown as 8.8781mm at Mode 2. The maximum displacement and stress at leaf spring are shown as 0.0458 mm and 72.533 MPa respectively on 1200 Hz. The comfortability of passenger becomes better on leaf spring at suspension system by use of this design model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.6
• /
• pp.43-50
• /
• 2010

This study aims to analyze the structural safety by comparing deformation and equivalent stress of door with a stiffener or no stiffener when the door crashes against something in case of overturn. Three types are classified on the basis of the no stiffener model in the vehicle door. One is the type which has a stiffener. Another is the type which has no stiffener and the other is the type which has a hole in the stiffener. These three types are compared with each other by analyzing. This side door of vehicle is the automotive part about the kind of vehicle as Mercedes Benz E-Klasse scaled down as 1/18 times as the real size. The study model of vehicle door is modelled by CATIA program and it is analyzed by ANSYS.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.2
• /
• pp.33-39
• /
• 2010

The thickness of original hinge model is changed for structural stability in this study. The front end with the largest deformation of 9.8813 mm or the rear middle part with the largest equivalent stress of 6082.6 MPa is respectively shown at door hinge. The lower part of joint pin head with the largest deformation of 0.17499 mm and the largest equivalent stress of 1540.2 MPa are shown. The advanced model with more thickness and stability is shown to have smaller displacement in half and smaller equivalent stress by 3 times by comparing with the original model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.2
• /
• pp.53-59
• /
• 2010

Stress analysis and fatigue life on shock absorber are investigated in this study. The lower part of spring is shown with the maximum equivalent stress and displacement of 153.49MPa and 26.151mm. The rear part is also shown with the number of fatigue life less than $6.8241{\times}10^5$. And the middle part of spring is shown with the minimum safety factor of 0.94592. The designed modeling suspension in this study has no possibility with resonance. As the result of this study is applied by the chassis of automobile, the prevention on fatigue fracture and the durability is predicted.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.28-33
• /
• 2018

The automotive front bumper guard is the most important part of the vehicle for protecting the life of driver when a traffic accident happens. In order to ensure safe driving, this part must possess sufficient strength and durability. This study was carried out with structural and fatigue analyses by designing front bumper guard models. After the lowest value for maximum total deformation and equivalent stress was found through structural analysis and the highest value for fatigue life was found for all three models, it was shown that the type C front bumper guard model was the most suitable for application to a real car. The strength property and durability of the optimum design were determined through this study's results.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.34-38
• /
• 2018

Recently, the turbo charger has become an important part because it yields little displacement and high power while downsizing the engine's fuel ratio for environmental purposes. In this study, flow analysis was conducted to form the basis of data regarding the best efficiency. The axial displacement was changed from none to 25 mm by controlling the configuration of the turbo charger and the flow analyses were compared with each other. The maximum rate of the outlet of model 1 was 46.36 m/s and the maximum pressure of model 4 was 0.761946 Pa. The maximum flow rate of model 4 was 0.000187650 kg/s. This study's result should aid in the effective design of a turbo charger with high performance.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.3
• /
• pp.47-53
• /
• 2005

The non-linear finite element program of the large deformation analysis by computer simulation has been used in the prediction and evaluation of the behaviors of the non-linear rubber components. The analysis of rubber components requires the tools modelling the special materials that are quite different from those used for the metallic parts. The nonlinear simulation analysis used in this study is expected to be widely applied in the design analysis and the development of several rubber components which are used In the manufacturing process of many industries. By utilizing this method, the time and cost can also be saved in developing the new rubber product. The objective of this study is to analyze the rubber component with the large deformation and non-linear properties.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.139-144
• /
• 2004

Dynamic crack initiation in ductile steel is investigated by means of impact loaded 3 point bend(PB) specimens. Results from non-viscoplastic and viscoplastic materials are compared. Their materials are applied with various impact velocities and static strain rates. The specimen has the size 320${\times}$750 mm with a thickness of 10 mm. A modified 3PB specimen design with reduced width at the ends has been developed in order to avoid the initial compressive load of the crack tip and also to avoid the uncertain boundary conditions at the impact heads. Numerical simulations are made by using the FEM code ABAQUS. Therefore, their results are plotted by shapes of the von Mises plastic stress and equivalent plastic strain of the specimens applied by various impact velocities.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.192-194
• /
• 2007

교토의정서 발효 후 유럽을 중심으로 한 선진국에서는 온실가스 배출권거래제를 국제사회에 보급함으로서 경제적 이익을 창출하고자 한다. 우리나라의 이산화탄소배출량은 세계 상위권 수준이며 이에 대한 대책이 절실히 필요한 시점이다. 철도선진국은 전 세계적으로 대두되고 있는 지구온난화문제를 신속하고 적극적으로 대처하고 있으나 국내 철도부분에서의 온실가스배출저감에 대한 대응은 미흡하다. 본 논문은 현재 철도분야의 대응방안, 철도급전시스템에서 신재생에너지를 이용한 에너지 대체방안과 에너지절약 방안 등을 다룬다.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.238-240
• /
• 2007

This paper present adaptation method of rail potential test to verify DC railway system's performance and safety. For protection of person and utility caused by rail potential rise, international standard to limit rail potential rise is made and rail potential is tested at the time of plan and construction of DC railway system in foreign country. So, we need rail potential test at the opening time and prepare a continuous monitoring technique of rail potential and a limitation method of rail potential rise. For these, we describe cause of rail potential rise, international standard about rail potential, protection principle, an example of calculation and measurement, and adaptation method for performance test.