• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.825-830
• /
• 1999

The purpose of this study is to improve overall performance of prefoamed lightweight cellular concrete for On-Dol system floor. This study includes 4 sections as follows. \circled1 Analysis of the structural characteristics of On-Dol System focusing on the lightweight cellular concrete insulation layer. \circled2 Establishment of the mixing design equations. \circled3 Development of some admixtures used with foaming agent. \circled4 Improvement of the equipment for onsite production. This study has proven that, compared with the current existing one, the newly developed lightweight cellular concrete has been reduced the usage of cement by 20% and the cracks caused by cement drying shrinkage up to 80% but has shown the increased compression strength by 20% at 7 days curing period. The volume contraction of freshly prepared cellular concrete by the loss of foam was hardly found in newly developed lightweight cellular concrete.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.204-206
• /
• 2014

석탄 화력발전소에는 연소가스의 질소산화물(NOx) 저감을 위한 SCR(selective catalytic reduction)설비가 운전되고 있으며, SCR은 환원제인 암모니아($NH_3$)를 이용하여 연소가스 내에 질소산화물을 물과 질소로 분해하는 역할을 한다. 그러나, 연소가스 중의 일부 삼산화황($SO_3$)과 미반응 암모니아가 결합하여 황산암모늄염(Ammonium bisulfate; $NH_4HSO_4$)을 생성하며, 이는 후단 APH(air preheater)의 열소자에 점착된 후 분진들과 함께 성장하여 막힘을 야기한다. 막힘이 발생된 APH는 연소가스의 흐름을 방해하기 때문에 차압을 증가시키며, 이는 발전효율의 감소뿐만 아니라 급전정지를 초래한다. 이를 해결하기 위하여 $CO_2$ 드라이아이스 세정 방법을 적용하였으며, pilot-scale plant에서 실험을 수행하였다. 또한, 드라이아이스 공정변수인 분사압력과 분사시간을 제어하여 pilot-scale plant의 APH 열소자 표면에 생성되어있는 오염물질들의 제거효율을 관찰한 결과 95 %의 높은 제거효율을 보였다.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.28-35
• /
• 2003

Quaternary faults found around the Ulsan Fault System can be divided into 4 types based on the fault outcrop features : Type I fault cuts basements and Quaternary deposits of which remain on both hangwall and footwall. Type II fault is developed only in Quaternary deposit. Type III fault has inclined unconformity after Quaternary faulting. Type IV fault is common type around the Ulsan fault system and has horizontal unconformity surface after cutting earlier Quaternary deposit. After erosion, later Quaternary deposit overlays on both old deposit and basement. The Ulsan Fault System consists of three segments at large scale from north to south based on the lineament rank and shape, Quaternary fault location, and slip rate. The segment boundaries are identified by the existence of the two intervals which show no lineaments and Quaternary faults. But, if detail fault parameters could be obtained and used in segmentation, it can be divided into more than three segments.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.30.1-30.1
• /
• 2011

2010년 11월 05일부터 11월 29일 중 총 12일간 진천 소재 충북대학교 천문대의 60cm 반사망원경과 ST-8 CCD 카메라를 이용하여 BD And의 BVR CCD 측광 관측을 수행하여 처음으로 BVR 광도 곡선을 완성하였다. 또한, 극심시각 결정을 위한 측광관측이 레몬산 천문대 1m 반사 망원경과 충북대학교 천문대의 35cm 망원경으로 수행되었다. 우리의 관측을 통하여 모두 19개의 극심시각을 새로이 결정하였다. 새로운 관측은 이 별의 공전주기가 이전까지 알려진 0.4629일이 아니라 그 두 배인 0.9258일이며, 기산점도 반주기 바뀌어야 함을 보여준다. BD And의 광도요소를 $MinI=HJD2434962.8602+0.^d9258054E$으로 새롭게 개정하였다. 이 광도요소로 작성한 우리의 BVR 광도곡선은 제1식과 제2식의 깊이가 거의 비슷하며, 식바깥 부분에 잘 발달된 파형 모양을 보인다. 이는 BD And가 짧은 주기의 RS CVn형 식쌍성임을 나타내는 것이다. 우리의 극심시각을 포함한 총 130개의 극심시각에 대한 (O-C)도를 작성한 결과, BD And의 공전주기가 규칙적으로 변화하는 것을 발견하였다. 이 변화를 보이지 않는 제3천체에 의한 광시간 효과로 가정하여, 궤도이심율이 0.78이며, 9.19년의 주기를 가진 광시간 궤도를 결정하였다. 우리의 광도곡선을 2003년 Wilson-Devinney 쌍성 모형으로 분석하여 광도곡선 해를 질량비 q=0.094, 궤도경사각 $i=85.^{\circ}4$, $T_1=6365(K)$, $T_2=6250(K)$, $R_1=1.132(Rsun)$, $R_2=1.304(Rsun)$와 같이 산출하였다. 식바깥에서 나타나는 파형 모양의 변화는 주성의 표면에 매우 큰 흑점으로 잘 설명되며, BVR 광도곡선에서 각전체 광도의 각 8.3%, 10.0%, 11.7%에 해당되는 제3 광도가 검출되었다. 이는 주기연구에서 제안된 제3천체의 존재 가능성을 더 공고히 한다.

• Journal of Hospice and Palliative Care
• /
• v.6 no.2
• /
• pp.144-151
• /
• 2003

Purpose : The purpose of this study was to identify the current status of symptom and pain control in cancer patients treated with chemotherapy. Methods : The study population consisted of 66 cancer patients treated with chemotherapy and the data was collected by chart audit and using questionnaire from 19 clinicians in an university hospital during the period of August 7 to 24, 2001. The degree of symptom, analgesics type, dose, administration route, and pain control method of cancer patients treated with chemotherapy was investigated. The collected data were analyzed by frequency, percent, mean, and SD using SPSS $PC^+$ program. Results : The number of cancer patients treated with chemotherapy was 66, male 35 (53.0%), female was 31 (47.0%). The largest of age group was $61{\sim}69$(34.8%) years old. Most frequent cancer site was stomach 19 case (28.8%), cole-rectal 17 case (25.8%), urinary 11 case (16.7%) in the respective order. The most common stage of cancer was stage 3, 14 case (29.2%). The most frequent duration of diagnosis was under 3 month, 25 (37.9%). The frequent symptom of cancer patients treated with chemotherapy was marasmus ($2.4193{\pm}1.2220$), pain ($1.9333{\pm}1.2194$), sleep disorders ($1.7142{\pm}1.0384$), personality change ($1.5806{\pm}0.8971$) in the respective order. 3) The analgesics used for pai control were narcotic analgesics 66.2% and nonnarcotic analgesics 33.8%. Pain control method were regular basis+as needed 47.4%, as needed 31.6%, regular basis 21.0% in order. Administration route were oral 50.7%, injection 41.8%, patch 7.5% in order. Conclusion : The most frequent symptom of cancer patients treated with chemotherapy were marasmus and pain. The frequent analgesics was narcotic analgesics but 21% of the clinician regularly prescribed analgesics for pain control. Thus this prescription was insufficient for pain control. Administration route that were used more oral or injection than patch. Based on this evidence, it seemed that more active practice and education about evaluation and pain control of cancer patients treated with chemotherapy are needed.

• The Journal of the Petrological Society of Korea
• /
• v.25 no.3
• /
• pp.195-209
• /
• 2016

The understanding of geometric complexity of strike-slip Fault system can be an important factor to control fault reactivation and surface rupture propagation under the regional stress regime. The Kumamoto earthquake was caused by dextral reactivation of the Futagawa-Hinagu Fault system under the E-W maximum horizontal principal stress. The earthquakes are a set of earthquakes, including a foreshock earthquake with a magnitude 6.2 at the northern tip of the Hinagu Fault on April 14, 2016 and a magnitude 7.0 mainshock which generated at the intersection of the two faults on April 16, 2016. The hypocenters of the main shock and aftershocks have moved toward NE direction along the Futagawa Fault and terminated at Mt. Aso area. The intersection of the two faults has a similar configuration of ${\lambda}$-fault. The geometries and kinematics, of these faults were comparable to the Yansan-Ulsan Fault system in SE Korea. But slip rate is little different. The results of age dating show that the Quaternary faults distributed along the northern segment of the Yangsan Fault and the Ulsan Fault are younger than those along the southern segment of the Yansan Fault. This result is well consistent with the previous study with Column stress model. Thus, the seismic activity along the middle and northern segment of the Yangsan Fault and the Ulsan Fault might be relatively active compared with that of the southern segment of the Yangsan Fault. Therefore, more detailed seismic hazard and paleoseismic studies should be carried out in this area.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2460-2468
• /
• 2014

A local rain that is concentrated in specific area in a short time frequently occurs due to recent abnormal weather. To prevent potential flood disasters, therefore, it is necessary to be established to the flood control system. Checking the river design standard, however, hydrologic design frequency of water gate is only marked as over 20 years, so this fact shows that the standard is unclear. The inland inundation modeling considering the stage in a river and quantitative assessment are required to reduce flood damage. The simulation for internal inundation is very complex and is time-consuming due to considering hydraulic hydrology characteristics at the same time. Using the already established river master plan, consequently, this study proposed the simple and convenient method for assessment of the internal inundation simulation. Using the proposed method in the upper and middle regions of a river, influences for design frequency or water gate location were assessed by applying the nine probability precipitation with design frequency and by targeting the water gates which are installed in five inlands.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.294-299
• /
• 2010

Thermal stability of exo-tetrahydrodicyclopentadiene (exo-THDCP) were investigated in a batch-type reactor perfectly coated with quartz. The 1 ml liquid product, which was a sufficiently small amount so as not to affect the reaction pressure, was sampled at 90 min intervals during the reaction and determined by gas chromatography-mass spectrometry (GC-MS) to measure thermal decomposition products of exo-THDCP and specify mechanism for additives (thermal stabilizer). Hydrogen donors (thermal stabilizer) such as 1,2,3,4-tetrahydroquinoline (THQ), benzyl alcohol (BnOH) increased thermal stability of exo-THDCP. These materials donated hydrogen to radical of exo-THDCP produced after initiation of exo-THDCP to decrease activity of primary products of exo-THDCP.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1999-2004
• /
• 2011

This research aims to develop polymer composites which can be used for PEMFC bipolar plate by injection molding process. Considering the moldability and stiffness, we used LCP(Liquid crystal polymer) as base resin. In order to improve electrical conductivity and mechanical properties, we chose carbon black, and both synthetic graphite and expanded graphite. The composites with different recipe are prepared for injection molding of PEMFC bipolar plate and CAE(Computer Aided Engineering) analysis was performed to predict melt flow and fiber orientation We did successfully fabricate the ASTM specimens by injection molding, and measure the electrical conductivity of the samples by using four point probe device. We measured mechanical properties such as flexural strength, flexural modulus and Izod impact strength. Conclusively, the electrical conductivity increased with increasing additive concentration, but both flexural strength and Izod impact strength decreased due to the brittle nature of carbon-based additives.

• Composites Research
• /
• v.18 no.4
• /
• pp.14-20
• /
• 2005

To determine the effect of chemical structure of aromatic amino curing agents on thermal and mechanical properties, standard epoxy resin DGEBF (diglycidylether of bisphenol F) was cured with diaminodiphenyl methane (DDM) and diaminodiphenyl sulphone (DDS) in a stoichiometrically equivalent ratio. From this work the effect of aromatic amino curing agents on the thermal and mechanical properties is significantly influenced by the chemical structure of curing agents. In contrast, the results show that the DGEBF/DDS system having the sulfone structure between the benzene rings had higher values in the thermal stability, density, shrinkage ($\%$), thermal expansion coefficient, tensile modulus and strength, flexural modulus and strength than the DGEBF/DDM system having methylene structure between the benzene rings, whereas the DGEBF/DDS system presented low values in maximum exothermic temperature, conversion of epoxide, and grass transition temperature. These results are caused by the relative effects of sulfone group having strong electronegativity and methylene group having (+) repulsive property. The result of fractography shows that the grain distribution of DGEBF/DDS system is more irregular than that of the DGEBF/DDM system.