• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1229-1234
• /
• 2001

There are three items, which are panhead displacement, tilting angle of pan head, required moment of main shaft, which representing kinematic performance of pantograph. Kinematic variables effective on kinematic performance are length of each components and installation angle, In this study, cost function is defined with 3 items, By this cost function, length of thrust rod was optimized. Finite element analysis was used to consider structural soundness. Finite element model was qualified by comparison between analysis result with experiment result. By qualified F.E, model various severe condition was simulated to consider structural soundness.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.555-564
• /
• 2001

Wheel-rail noise is normally classified into three catagories ： rolling, squeal and impact noise. In this paper, rolling noise caused by the irregularity between a wheel and rail is analysed as follows： The irregularity between the wheel and rail is assumed as combination of sinusoidal profiles. Wheel-rail contact stiffness is linearized by using Hertzian contact theory, and then contact force between the wheel and rail is calculated. Vibration of the rail and wheel is calculated theoretically by receptance method or FEM depending on the geometry of wheel or rail for the frequency range of 100-5000Hz, important for noise generation. The radiation caused by those vibration is computed by BEM. To verify this analysis tools, rolling noise is calculated by preceding analysis steps using typical roughness data and it is compared with experimental rolling noise data. This analysis tools show reasonable results and used for the prediction of KTX rolling noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1215-1220
• /
• 2001

Wind tunnel test of a new pantograph, that is developed through the KHST project, was performed in RTRI wind tunnel test center of Japan end of last June. This paper indtroduces the measurement results and analysis of noise measurement part that is achieved during the wind tunnel test. The maximum measured sound pressure level at 5m shows 102.3dB(A) at 350km/h and it leads to 88.3dB(A) of predicted sound pressure at 25m that satisfy 91dB(A) of evaluation criteria. Major noise sources of the pantograph was identified as a link between upper and lower arm, panhead contact strips and shunt wires.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.379-387
• /
• 1998

HVAC systems are used to maintain comfort conditions in occupied spaces. Like rolling noise and aerodynamic noise, noise from the HVAC system of train increases interior noise level. For an appropriate interior noise level, it is necessary not to find noise sources and their propagation paths. Noise emission from the sources and propagation through the propagation paths should be regulated in order to reduce their effect to the interior noise level. In general, the main noise source in the HVAC system is blower which operates at high static pressure. This noise propagates through ducts which are directly connected to the residential area. Since the blower noise can be reduced only to some degree, it is necessary for the propagation paths to have enough noise attenuation. Acoustic properties of ducts are usually found by experimental methods but it is rather difficult and expensive to set up such test equipments. In this thesis, the design and the noise characteristics of TGV-K HVAC system are studied. Finite element method in accordance with experimental method is used to study the acoustic properties of TGV-K duct system.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.445-452
• /
• 1998

The dynamic performance design of catenary-pantograph system which collects current for the next generation Korean high speed train(KHST) was considered. Used was the same dynamic model of the catenary-pantograph system as that of TGV-K which will be introduced for Kyung-bu corridor. Using the model , sensitivity analysis fer design variables were made to improve dynamic performance of KHST system. The results of sensitivity analysis and performance improvement are as follows: (1) It was found that aerodynamic force, tension of contact wire, mass of contact strip, mass of supporting contact strip, mass of clamp, mass of steady arm, and stiffness of plunger were the design variables most influencing the dynamic performance of the system. (2) Pantograph with reductions of 20% aerodynamic force, 34% weight of supporting contact strip, 20% spring constant of plunger, and 34% equivalent mass of steady arm was very possible system for the KHST which will be running at maximum operating speed 350 km/h.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.476-488
• /
• 1998

The study was carried out about the development of the propulsion and the control systems toy Korean High Speed Train. The propulsion system was studied to run the maximum operating speed of 350km/h. The capacity of the main equipments is decided for the train to run the maximum operating speed of 350km/h with one Ike of 2 power cars, 4 motorized trailers and 14 intermediate trailers. The control system was studied to two parts the supply and the control of high and low voltages used at train. The performance study of control system would be continued for interface with other systems.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.189-201
• /
• 1999

According to the current trend of single arm type pantograph for high speed trail korean pantograph designed to single arm type will be installed on each power car roof of prototype train of korean very high speed rail configured to 7 cars and have the characteristics of maximum 1% contact loss at 350 km/h speed. This study is devoted to design basically element components of pantograph for korean very high speed train on the basis of kinematic analysis, static analysis and dynamic analysis, followed by making the basic drawings of korean pantograph. This drawings will be complemented through certification tests of prototype pantograph and verification of analysis software.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.479-486
• /
• 1999

The noises generated from the air-conditioning duct are known to strongly affect the indoor-noises of high speed trains. The acoustic characteristics of an air-conditioning duct should depend on the geometry and shape of the duct. The structural material for Korean high speed train is supposed to be changed from Steel, which was used for TGV, to Aluminum in order to reduce the total train weight. Accordingly, the shape and layout of the air-conditioning duct of Korean high speed train will be different from that of TGV. Thus, this paper introduces a analytical method to predict the noise attenuation through the air-conditioning duct, based on the ISO 7235. In this method, the whole duct is divided into several pieces and the noise attenuations predicted for each duct piece are integrated to get the noise attenuation for the whole duct system. The validity of the method introduced herein is discussed through some numerical tests.

• Journal of the Korean Society for Railway
• /
• v.7 no.1
• /
• pp.26-31
• /
• 2004

A study is conducted to clarify internal and external pressure variation of passenger cabin for KTX. These pressure variation may give rise to the ear-discomfort for passenger and fatigue for carbody. In this study, the pressure variation of interior, gangway and exterior of KTX passenger car is measured by using the atmospheric pressure sensors and portable data acquisition system. The tunnel from 4000m to 200m in length are chosen far the investigation of tunnel length effects. From the results of experiment, the pressure variation of interior per second is under the ear-discomfort limitation in all of tunnel. And, We found that there are similar patterns of exterior pressure variation for each critical tunnel length. These results generally agree to RTRI's experimental result fur Shinkansen.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.172-180
• /
• 1999

The major subject of this paper is to develop the concept fur a Korea high speed train system and recommend to train configuration. High speed train configurations are basically concerned traction power(train configurations with concentrated; CPT or distributed Power system: DPT) and train design(single car as compared with articulated bogies). The result of configuration, a advantages and disadvantaged were necessitated by different train configurations; -distributed underfloor power have an increased length for the seats by 15% as compared with the concentrated power trait - articulated trainsets are characterised by less of number of bogies and reduced values of mass, train resistance, noise and vibration. from the result, the optimized train concept combining high seat capacity per train length with low weight and train resistance is 400m long, single -floor train composed of two symmetrically arranged half trainsets. Therefore, at this work recommended distributed train system However, the final decision of Korea high speed train configuration was concentrated power train and articulated bogie system. The configuration of trainset was 20cars included 2 power cars, 4 motorized cars and 14 trailer cars.