• Korean Journal of Remote Sensing
• /
• v.13 no.2
• /
• pp.99-120
• /
• 1997

Solar radiation is scattered and absorbed atmospheric compositions in the atmosphere before it reaches the surface and, then after reflected at the surface, until it reaches the satellite sensor. Therefore, consideration of the radiative transfer through the atmosphere is essential for the quantitave analysis of the satellite sensed data, specially at shortwave region. This study examined a feasibility of using radiative transfer code for estimating the atmospheric effects on satellite remote sensing data. To do this, the flux simulated by LOWTRAN7 is compared with CAGEX data in shortwave region. The CAGEX (CERES/ARM/GEWEX Experiment) data provides a dataset of (1) atmospheric soundings, aerosol optical depth and albedo, (2) ARM(Aerosol Radiation Measurement) radiation flux measured by pyrgeometers, pyrheliometer and shadow pyranometer and (3) broadband shortwave flux simulated by Fu-Liou's radiative transfer code. To simulate aerosol effect using the radiative transfer model, the aerosol optical characteristics were extracted from observed aerosol column optical depth, Spinhirne's experimental vertical distribution of scattering coefficient and D'Almeida's statistical atmospheric aerosols radiative characteristics. Simulation of LOWTRAN7 are performed on 31 sample of completely clear days. LOWTRAN's result and CAGEX data are compared on upward, downward direct, downward diffuse solar flux at the surface and upward solar flux at the top of the atmosphere(TOA). The standard errors in LOWTRAN7 simulation of the above components are within 5% except for the downward diffuse solar flux at the surface(6.9%). The results show that a large part of error in LOWTRAN7 flux simulation appeared in the diffuse component due to scattering mainly by atmispheric aerosol. For improving the accuracy of radiative transfer simulation by model, there is a need to provide better information about the radiative charateristrics of atmospheric aerosols.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.10
• /
• pp.684-693
• /
• 2012

The stormwater runoff from the increasing paved roads and vehicles resulted in the increase in the pollutants load to adjacent water bodies. The granular media filtration facilities are the most widely adopted to minimize the non-point source pollution from motorways. It is essential to consider the severe variation of hydraulic condition, suspended solid (SS) characteristics, and the medium characteristics for stormwater management filter. In this study, different types of media, including sand, were tested and the performance of downflow sand filters was investigated under various linear velocity and influent solid particle size. Results showed that the best medium is the coarse sand with large grain size, which showed the specific SS removal before clogging of more than $8.498kg/m^2$, the SS removal of higher than 95%, and minimum head loss. Linear velocity did not affect the total solid removal, while the performance was improved when fine solid was introduced. It is suggested that the life of a downflow sand filter bed can be extended by deep bed filtration when influent particles are fine. However, the captured particles can be washed out after a long period of operation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.8
• /
• pp.15-26
• /
• 2011

In this paper, we present a new beamforming scheme for a downlink of multiuser multiple-input multipleoutput (MIMO) communication systems. Recently, a block-diagonalization (BD) algorithm has been proposed for the multiuser MIMO downlink where both a base station and each user have multiple antennas. However, the BD algorithm is not efficient when the number of supported streams per user is smaller than that of receive antennas. Since the BD method utilizes the space based on the channel matrix without considering the receive combining, the degree of freedom for beamforming cannot be fully exploited at the transmitter. In this paper, we optimize the receive beamforming vector under a zero forcing (ZF) constraint, where all inter-user interference is driven to zero. We propose an efficient algorithm to find the optimum receive vector by an iterative procedure. The proposed algorithm requires two phase values feedforward information for the receive combining vector. Also, we present another algorithm which needs only one phase value by using a decomposition of the complex general unitary matrix. Simulation results show that the proposed beamforming scheme outperforms the conventional BD algorithm in terms of error probability and obtains the diversity enhancement by utilizing the degree of freedom at the base station.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8643-8648
• /
• 2015

In this paper presents the design and demonstrate 8 W 3-stage HPA(High Power Amplifier) MMIC(Monolithic Microwave Integrated Circuits) for Ka-band down link satellite communications payload system at 19.5 GHz ~ 22 GHz frequency band. The HPA MMIC consist of 3-stage GaN HEMT(Hight Electron Mobility Transistors). The gate periphery of $1^{st}$ stage, $2^{nd}$ stage and output stage is determined $8{\times}50{\times}2$ um, $8{\times}50{\times}4$ um and $8{\times}50{\times}8$ um, respectively. The fabricated HPA MMIC shows size $3,400{\times}3,200um^2$, small signal gain over 29.6 dB, input matching -8.2 dB, output matching -9.7 dB, output power 39.1 dBm and PAE 25.3 % by using 0.15 um GaN technology at 20 V supply voltage in 19.5~22 GHz frequency band. Therefore, this HPA MMIC is believed to be adaptable Ka-band satellite communication payloads down link system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.262-269
• /
• 2016

This study examined the influent of a sulfur denitrification reactor using nitrified effluent from a batch type reactor. The denitrification efficiency was compared according to the injection type. The nitrogen removal effects were compared with the changes in the EBCT and nitrogen concentration of the influent to determine the optimal operation conditions with the selected injection type. A denitrification efficiency evaluation of a reactor according to the change in injection type and up-flow was performed using a lower organic concentration of the effluent than the down-flow because of the re-precipitation of desorbed microbes and spilled solids. In the up-flow type, organics were controlled by the low concentration than the down-flow type because of solid re-precipitation. The T-N removal efficiency of the up-flow type was 73.3~90.2%, which was more that 10% higher that down-flow type. This means that the up-flow type has a great advantage in removing T-N and organics. The T-N removal efficiency by EBCT at 1hr was 47.3%, and was 88.1% and 90.5% by EBCT 3hr and 5hr, respectively. Therefore, the optimal operation conditions to remove nitrogen was considered to be EBCT for 3hr. After careful consideration of rule of law and T-N removal effects, the T-N load factor in the reactor should remain below $0.443kgT-N/m^3{\cdot}day$ to maintain the legal total nitrogen concentration for discharge, which is 20mg/L.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.443-443
• /
• 2014

CIS 박막을 제조하기 위한 방법으로 셀렌화(selenization)방식, MOCVD방식, 동시진공증발(co-evaporation)방식, 전착(electrodeposition)방식 등이 있으나, 이러한 방식을 이용하여 CuInSe2 박막을 제조하는 경우 어떤 방법으로든 다원화합물의 조성 및 결정성을 조절하기가 매우 어려운 단점이 있었다. 기판의 온도를 일정 온도로 유지하도록 하고, 증발원을 가열하여 이에 내포된 물질(이원화합물 또는 단일원소)을 증발시켜 기판에 증착이 이루어지도록 하거나, 기판의 온도를 승온시키고 구리 이원화합물을 내포한 증발원을 가열해 물질을 증발시켜 기판에 증착이 이루어지도록 하는 방법으로 기판에 박막이 형성되도록 한다. 기판의 대면적화로 인해 균일한 박막의 형성이 어려워지고 있으며, 이중 15% 이상의 고효율을 보인 방법은 3-stage process를 이용한 동시진공증발방식으로, Cu, In, Ga, Se 등의 각 원소를 동시에 진공 증발시키면서 조성을 조절하여 태양전지에 적절한 전기적, 광학적 특성을 가지는 Cu(In,Ga)Se2 (CIGS)박막을 증착시키는 방법이다. 일반적으로, 실험실에서 연구되고 있는 장비의 구조는 증발원이 아래에 장착되어서 상향 증착되는 방식이다. 본 연구에서 사용된 장비는 하향 증발원이 측면에 장착되어서 하향 증착되는 방식으로 구성하였다. 증착되는 면방향으로, 적외선온도계(pyrometer)가 설치된 시창(viewport)의 오염 등으로 인하여, 지속적인 공정이 이루어지기 힘든 점을 개선하여 증착기판의 후면에 적외선 온도계를 설치하여 기판의 온도변화를 감지하여 공정에 반영할 수 있도록 하였다. 본 연구에서는 하향식 진공 증발원, 기판후면 온도모니터링모듈 등을 개발 장착하여, CIGS 박막을 제조하였으며, 버퍼층은 moving 스퍼터링법으로 ZnS를 증착하였고, 투명전극층은 PLD(Pulsed Laser Deposition)를 이용하여 제조하였다. 가장 높은 광변환효율을 보인 Al/ZnO/CdS/Mo/SLG박막시료는 유효면적 $0.45cm^2$에 광변환효율 15.65 %, Jsc : $33.59mA/cm^2$, Voc : 0.64 V, FF : 73.09 %를 얻을 수 있었으며, CdS를 ZnS로 대체한 Al/ZnO/ZnS/Mo/SLG박막시료는 유효면적 $0.45cm^2$에 광변환효율 12.45 %, Jsc : $33.62mA/cm^2$, Voc : 0.59 V, FF : 62.35 %를 얻을 수 있었다.

• 한국지형공간정보학회:학술대회논문집
• /
• 2002.03a
• /
• pp.106-112
• /
• 2002

최근 급속한 도시의 팽창 및 신도시 건설과 산업의 발전으로 가스시설은 꾸준히 확대되고 있는 실정이다. 그리고 94년 아현동 도시가스사고와 95년 대구 도시가스사고 이후로 도시 가스 시설물의 대한 안전 대책 및 시설물 관리에 대한 국민들의 관심이 증대되었다. 이러한 흐름에 따라 가스회사들은 GIS 기술을 도입하여 기존에 수작업으로 관리되고 있는 가스시설 정보체계를 전산화하여 항상 최신의 현황을 유지하고, 사고 발생시 신속한 대처 방안 및 피해예측을 위한 시스템을 개발하기 위하여 많은 연구를 진행하고 있는 실정이다. 본 연구의 목적은 안전이 중요시되는 가스시설물에 대하여 가스사고 발생시 신속한 대처 및 처리방안을 제시할 수 있는 GIS 기반의 가스사고 관리시스템을 개발하는데 있다. GIS의 가스사고 관리시스템에서는 사고 발생시에 시설물 관리자가 사고 지점을 선택하여 우선적으로 공급을 중단해야 할 관로를 제시하고 사고지점을 검색하여 차단해야 할 밸브에 대한 정보를 신속히 제공하여 대응 방안을 제시 할 수 있도록 하였다. 아울러 가스공급이 중단되는 지역에 대한 정보를 추출하여 피해범위를 산정하여 효율적인 사고 관리를 지원하도록 구성되었으며, 이와 함께 잔존가스량을 구하여 사고후의 대처방안을 마련할 수 있는 기능을 제공하도록 하였다. 향후 연구과제로는 원격으로 가스 시설물을 감시하고 제어할 수 있는 원격감시/제어시스템(SCADA System)과 연계를 통하여 가스사고 후에 신속한 피해예측 및 피해를 최소화 할 수 있는 방안제시 및 GPS를 활용하여 신속한 사고처리를 할 수 있는 활용 방안을 연구하여 체계적이고 종합적인 가스사고의 관리가 필요하다고 사료된다. 또한, 사고 후의 긴급 대처방안 뿐만 아니라 잔존가스량을 이용하여 수용가에 가스의 신속한 재공급을 위한 정보의 제공까지 한 단계 발전된 시스템의 개발이 추진되어야 한다.남산지역에 대해 정사영상과 10m간격의 DEM을 제작하였으며 1:1000 수치지도를 통해 제작된 DEM과 비교한 결과 총 43990개 격자점의 표고 차이는 평균 5.98m였다.여재 높이 100 cm에서 원수를 하향류 및 상향류로 주입하면서 하향류 20, 40, 80, 100 cm, 상향류 20, 40, 60, 80, 100 cm에서 시료를 채취하여 분석한 결과 모두 원수가 주입되는 부근 여재 높이 20 cm에서 가장 많이 제거되었다. 상향류 보다 하향류로 원수를 주입했을 때 제거효율이 높았다. $Fe^{+++}$을 $Fe^{++}$로 환원하는 $O^{-}_{2}{\cdot}$의 작용을 대신할 수 있음을 증명하며 이와같은 ascorbate 의존적인 $OH{\cdot}$ 의 생성은 ascorbate가 조직손상에 관여할 가능성을 시사하였다.었다. 정확한 예측치를 얻기 위하여 불균질 조직이 조사야에 포함되는 경우 보정이 요구되며, 골반의 경우 골 조직의 보정이 중요한 요인임을 알 수 있었다. 이를 위하여 불균질 조직에 대한 정확한 정보가 요구되며, 이는 CT 영상을 이용하는 것이 크게 도움이 되리라 생각된다.전시 슬러지층과 상등액의 온도차를 측정하여 대사열량의 발생량을 측정하고 슬러지의 활성을 측정할 수 있는 방법을 개발하였다.enin과 Rhaponticin의 작용(作用)에 의(依)한 것이며, 이는 한의학(韓醫學) 방제(方劑) 원리(原理)인 군신좌사(君臣佐使) 이론(理論)에서 군약(君藥)이 주증(主症)에 주(主)로 작용(作用)하는 약물(藥物)이라는 것을 밝혀주는 것이라고 사료(思料)된다.일전 $13.447\;{\mu}g/hr/g$, 섭취 7일중 $8.123\;{\mu}g/hr/g$, 절식 14일후 $10.612

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.5
• /
• pp.239-246
• /
• 2017

In case of observing only wave height and period in the field, various wave characteristics are mainly calculated by wave by wave analysis method. In this paper, an wave by wave analysis program using MATLAB language is developed. It is possible to perform a function such as 1) correction for mean water level, 2) calculation for zero crossing time, 3) calculation for individual wave height, 4) time interval by using zero upcrossing and downcrossing method. The applicability of the developed program to the data of 0.2 second interval observed by using the WaveGuide Radar installed on HeMOSU-1 was examined. Tidal level variation removal and zero crossing time estimation were determined by linear or quadratic interpolation. It was judged that the Goda method was appropriate for calculating individual wave height, and the method proposed in this study seems to be improved through subsequent research. Due to the fineness of the sample, it can be seen that characteristics of representative waves are different from the results calculated by zero upcrossing and downcrossing method.

• Geophysics and Geophysical Exploration
• /
• v.21 no.2
• /
• pp.112-124
• /
• 2018

Ocean-bottom seismic survey is a seismic acquisition technique which measures data by installing 4-component receiver on the sea floor. It can produce more improved data in quality than any other acquisition techniques. In the ocean-bottom seismic survey, however, the number of receivers is limited due to high cost. Since only a small number of receivers are used for acquisition, ocean-bottom seismic data may suffer from discontinuities of events over traces, which can result in spatial aliasing. In this paper, we implemented Kirchhoff migration using mirror-imaging algorithm to improve the quality of ocean-bottom seismic image. In order to implement the mirror imaging algorithm, the seismograms should be separated into up-going and down-going wavefields and the down-going wavefield should be used for migration. In this paper, we use the P-Z summation method to separate the wavefield. Numerical examples show that the migration results using mirror imaging algorithm have wider illumination than the conventional migration, especially in the shallow layers.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.3
• /
• pp.65-72
• /
• 2010

We propose the asymmetric 2.5Gbps/622Mbps PON(Passive Optical Network) in order to reduce the bandwith of filter at receiver with inverse RZ(Return to Zero) code coded downstream and NRZ(Non Return to Zero) upstream re-modulation. I theoretically analyze BER(Bit Error Rate) performance and the power sensitivity with the optimal threshold level by performing simulation with MATLAB according to the types of downstream data. The results have shown that the optimal threshold level at the optical receiver could be saturated at 0.33 as the optical received power increase more than -26dBm to keep $10^{-12}$ of BER to a minimum. Also the power sensitivity is more improved by about 3dB by fixing the threshold level at 0.33 than the conventional receiver. The proposed system can be a useful technology for optical access networks with asymmetric upstream and downstream data rates because the optical receiver can be used without controlling threshold levels and that does not require a light source in optical network unit (ONU) and its control circuits in the optical line termination (OLT).