• Geotechnical Engineering
• /
• v.3 no.3
• /
• pp.31-48
• /
• 1987

The vertical pressure due to soil prism load and surface surcharge load acts on buried pipe, and occasionally uplifting force due to earthquake or differential settlement acts on it. In this paper, study was performed to estimate the pressure acting on the buried pipe due to soil prism load through analyzing Marston-Spangler theory by new method. And loading tests on the buried flexible pipe were performed to study on the response of the pipe due to surface surcharge load. Also, through the estimation of uplifting resistance theory and uplifting test for buried pipe, the method to determine the maximum uplifting resistance of buried pipe was proposed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.27-27
• /
• 2000

본 연구에서는 풍력발전용 복합재 회전날개의 개념설계 및 상세 설계 과정에서 고려하지 않았던 특수 하중 조건에 대한 유한요소해석을 통해 회전날개의 구조적 안전성을 확인하였다. 하중조건으로는 IEC1400-1 국제규격을 기초한 GL 인증규격에 정의된 것으로 대기온도변화에 의한 열 응력 효과로 $40^{\cire}$ 에서 경화시킨 후 운용되는 환경조건이 $-20^{\cire}$ 인 경우를 고려하였으며, 실제 운용중의 회전날개 표면에 발생 할 수 있는 결빙에 따른 하중증가 효과, 그리고 풍력발전기의 급작스런 정지와 정상 작동 중에 순간적인 돌풍 및 발전기 고장 등으로 발생되는 동적 하중증가 효과 등을 고려하였다.(중략)

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.48-55
• /
• 2002

An Internet-based software called the Repair Advisory Service (RAS) was developed to assist aircraft composite repair. The RAS takes advantage of the web user interface and provides estimation of the failure loads of repaired composite laminates and Structural Repair Manual (SRM) with search capability. In this paper, a failure model of lap repair is discussed as an example of the modules in the RAS. The model takes into account anisotropy of each ply in the laminate and in the repair ply, and non-elastic behavior of the interlayer between the laminate and the repair patch. Failure loads calculated by the model were compared with test data, and a good agreement was found between the results of the model and the test.

• Composites Research
• /
• v.18 no.6
• /
• pp.19-25
• /
• 2005

This paper has performed an experimental study on the hybrid composite carbody of Korean tilting railway vehicle. The hybrid composite carbody has the length of 23m and is comprised of a 40mm-thick aluminium honeycomb core and 2mm-thick woven fabric carbon/epoxy face sheet. In order to evaluate the structural behavior and safety of the hybrid composite carbody, the static load tests such as vertical load, end compressive load, torsional load and 3-point support load tests have been conducted. The test was performed under Japanese Industrial Standard (JIS) 17105 standard. from the tests, the maximum deflection was 12.3mm and the equivalent bending stiffness of the carbody was $0.81\times10^{14}\;kgf{\cdot}mm^2$. The maximum strain of the composite body was below $20\%$ of failure strain of the carbon/epoxy face sheet.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.6
• /
• pp.715-724
• /
• 2011

A turn buckle inserted between tension members that sustain the structural loads in a suspension structure system is a device that is capable of adjusting the tensile force. The tension member is an important element of a tension structure, but no simple and economical method of measuring a tensile force applied to members has been proposed yet. Thus, a turn buckle for measuring the tensile force in a tension member was developed in this study. The turn buckles of the measurement limit loads of 100kN, 200kN, and 300kN were tested through a theoretical analysis and a finite element analysis. There was no significant difference in the results of the theoretical analysis, FEA, and the test. In addition, the ultimate strength of the turn buckle using FEA showed that a new turn buckle is sufficiently safe to use even when there is a five-times overload in the measurement limit load.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.2
• /
• pp.13-22
• /
• 2001

In this study, centrifuge model tests were fulfilled to investigate the characteristics of bearing capacity of paper ash as a filling material. The model tests were done varying the footing width and gravity level. The settlement and vertical soil pressure by loading were measured. The results from the tests were compared with the one from FLAC program using finite difference method and bearing capacity theory. After all, it was shown that the characteristics of load-settlement represented the local shear failure, which the settlement ratio s/B showed inflection point around 25~30%. As g-level and footing width were increasing, the load strength was increasing. The ultimate bearing capacity from the tests was very closed the results from Terzaghi's theory. As the distance from footing center was increasing, the vertical soil pressure was decreasing. If E/B is higher than 7, the stress by loading was almost increasing. The vertical displacement from loading was the largest one around under the footing and was almost occurred when the depth>4cm and E/B is higher than 5.0.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.251-258
• /
• 2017

비닐하우스는 원예시설 중 가장 중요한 구조물로서 전국에서 이용하고 있으며, 경제적이기 때문에 농업 재배에서 가장 많이 쓰인다. 폭설 시 눈에 의한 하중으로 비닐하우스의 속이 빈 파이프의 변형이 유도된다. 본 논문에서는 비닐하우스의 80%를 차지하는 단동식 구조를 모델로 삼아 비닐하우스 지붕 위치에 따른 눈의 하중을 계산한 후 EDISON 해석 프로그램과 상용 프로그램을 이용하여 비닐하우스에 최대 변위와 응력을 분석하여 농업진흥청에서 제안한 보강재를 해석했다. 추가로 보강재의 접하는 위치를 이동하여 최대 변위와 파이프에 가해지는 응력을 분석하였다.

• Composites Research
• /
• v.17 no.6
• /
• pp.52-57
• /
• 2004

In this study, mechanical tensile properties of carbon fiber reinforced polymeric (CFRP) composite cycled with thermo-mechanical loading under cryogenic temperature (CT) were measured using cryogenic environmental chamber. Thermo-mechanical tensile cyclic loading (up to 10 times) was applied to graphite/epoxy unidirectional laminate composites far room temperature (RT) to $-50^{\circ}C$, RT to $-100^{\circ}C$ and RT to $-150^{\circ}C$. Results showed that tensile stiffness obviously increased as temperature decreased while the thermo-mechanical cycling has little influence on it. Tensile strength, however, decreased as temperature down to CT while the reduction of strength showed little after CT-cycling. For the analysis of the test results, coefficient of thermal expansion (CTE) of laminate composite specimen at both RT and CT were measured and the interface between fiber and matrix was observed using SEM images.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.41-52
• /
• 2008

This paper concerns the load carrying capacity of back-to-back reinforced soil wall for use in roadway and railway construction. Two test conditions, designed with due consideration of the FHW A design guideline, were first developed and a number of cases having different reinforcement lengths were tested under a surchage loading until failure. The results indicated that for cases in which two sides of reinforcements do not overlap, the wall behavior was similar to those of single wall. For cases in which the reinforcements overlap each other, on the other hand, the load carrying capacity of the wall significantly decreased when reinforced with reinforcement layers having lengths less than 50% of the wall height.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.163-172
• /
• 2011

The CFTA girder developed is a concrete filled steel tubular system with arched shape and external post-tensioning (PT) tendons which control the initial camber and the bending stress of the girder. In the present study the effects of the PT tendons on the dynamic behavior of the girder subjected to a moving vehicle load are numerically investigated. Various levels for the tendon quantity and the tendon forces are considered, using the existing FE model of the girder. The vehicle considered is a DB-24 truck and is modeled with two tracks-three axles. Equivalent-load pulse time histories are applied to each node to simulate the moving vehicle, depending on the time of arrival and the discretization. The vehicle speeds are varied from 40 km/hr to 100 km/hr with increment of 20 km/hr. The analysis results show that the tendon forces do not produce any influences on the dynamic responses of the girder. However the dymamic deflection of the girder increases when a smaller amount of tendons is used. The Dynamic Amplification Factors (DAF) are evaluated based on the static and dynamic responses. Much lower values of the DAF are obtained, even no tendons applied, than those provided by the design criteria of the AASHTO LRFD and the Korea Highway Standard Specification.