• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.1-201.1
• /
• 2016

전주된 Invar (Fe-35%Ni) 박판 위에 증착된 Cu 박막은 스퍼터 전력량이 증가할수록 증착속도가 증가하였다. Cu/Invar 박판이 Invar 박판보다 면저항 값이 34%로 작았다. Invar 박판 위에 Cu가 증착되면 최대자화와 투자율은 각각 40.3, 65.0 [%] 감소하였다. Cu 박막의 탄성하강강성도, 마찰계수, 피로한계는 각각 45, 0.130, 0.093 이었다. 동적 나노 압침법으로 얻은 Invaar/Cu 박막의 하중-시간-변위 곡선의 가장 큰 차이는 탄성하강강성도(elastic stiffness) 이었다. 미세경도와 나노경도의 실험적 관계식은 $Y[GPa]=9.18{\times}10^{-3}X[Hv]$ 이었다. 나노압침선단의 하중분포를 이차원 선형 및 비선형 유한요소해석을 통하여 1.0 [mN] 의 정적하중을 가한 Cu 박막은 486 [mN] 으로 예측되었다. 이는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.168-170
• /
• 2019

본 논문은 효과적인 능동 풀-다운 기능을 위한 새로운 구조의 펄스 파워 모듈레이터를 제안한다. 제안된 능동 풀-다운 방식은 별도의 풀-다운 저항을 사용하지 않고, 펄스 방전 패스에 추가된 다이오드의 역회복 특성을 이용하여 풀-다운 기능을 수행한다. 본 논문에서 사용된 풀-다운 다이오드는 펄스 출력 시에는 정방향 바이어스 상태를 유지하다가, 펄스 출력이 제거되면 비교적 긴 역회복 구간동안 부하의 커패시턴스 성분에 남아있는 에너지가 방전될 수 있는 전류 패스를 제공한다. 이에 따라 제안된 구조의 펄스 모듈레이터는 기존에 제안된 풀-다운 회로에서 발생하는 발열 손실 또는 별도의 복잡한 제어회로와 같은 복잡한 구조의 문제를 보완하고 빠른 펄스 하강시간을 달성할 수 있다. 본 논문에서는 시뮬레이션을 통해 기존에 제안되었던 풀-다운 저항 방식과 풀-다운 스위치 방식, 제안하는 방식을 비교하여 제안된 구조의 성능과 우수성을 분석하였다.

• Applied Chemistry for Engineering
• /
• v.9 no.6
• /
• pp.901-906
• /
• 1998

Gas and liquid flow characteristics were investigated in an internal circulation airlift reactor using a single nozzle for a gas distributor. In three reactors with different diameters of the downcomer and heights of the riser, the gas holdup in the individual flow zone and the impulseresponse curve of tracer for an air-water system were measured for various gas velocities and reactor heights. Experimental results showed that the flow behavior of bubbles in the riser was the slug flow due to strong coalescences of bubbles and that the bubble flow pattern in the downcomer was the transition bubble flow for the smaller diameter of the downcomer, however, it was the homogeneous bubble flow for the larger one. And mean gas holdups in the individual flow zone and the reactor were greatly increased with decreasing the diameter of the downcomer for the equal ratio of height of the top section to that of the riser. Also, the mixing time was much effected by the height of the top section of reactor and for the equal ratio of height of top section to that of the riser, it was increased with increasing the diameter of the downcomer and the height of the riser. Flow characteristics of liquid were mainly varied with the bubble flow pattern in the downcomer and the size of the top section of reactor. And circulation velocities of liquid in the riser were increased with increasing gas velocities and the size of the top section of reactor, and for the equal ratio of height of top section to that of the riser, they were increased with increasing the diameter of the downcomer and the height of the riser.

• Electronics and Telecommunications Trends
• /
• v.12 no.6 s.48
• /
• pp.131-135
• /
• 1997

본 고는 ATM교환기 고온 상태 동작 특성을 시험하기 위하여 온도 조건, 시험 시간, 시험 절차, 시험 방법, 세부 기준, 판정 기준 등을 정한 것으로, 고온 동작 기준은 한국통신 환경 관리기준 및 품질 표준서-4101을 근거로 하였다. 온도 조건은 평균 $49^{\circ}C$를 유지하되 허용편차는 $1^{\circ}C$내외로 시험되어야 하며, 시험 시간은 온도 상승 및 하강 시간과 장애 발생시 고장 조치 시간 등을 포함하여 최대 72시간을 넘지 않아야 하고, 고온 유지시간은 48시간으로 채택한, ATM 교환기 고온 시험 방법과 기준을 제시하였다.

• Horticultural Science & Technology
• /
• v.28 no.5
• /
• pp.783-789
• /
• 2010

The effective method for heating root-zone during winter season was studied in the aspects of growth, yield and economics for tomato ($Solanum$ $lycopersicum$) in perlite bag culture. There were four root-zone heating treatments: two hours heating from one hour before to one hour after sunrise, four hours from two hours before to two hours after sunrise, 15 hours after sunset, and no heating. The growth characteristics of the upper parts of plants were not significantly different among the treatments, but root volume increased with longer heating of the root zone. The Plant Development Index, using stem diameter and the length between growing tip and the upper flowering truss, showed relation between yield per cluster and growth pattern. The treatment heating for four hours was the most economic in terms of growth and yield of tomato.

• Korean Journal of Ichthyology
• /
• v.19 no.2
• /
• pp.93-100
• /
• 2007

The effects of sudden changes of water temperature (WT) on the physiological response and hematological characteristics of the goldfish (Carassius auratus) were examined by manipulating WT in a flow through freshwater culture system with tanks. The WT was dropped from $15^{\circ}C$ to $10^{\circ}C$ within 1 hour and then returned to the original water temperature within 12 hours and maintained for 12 hours at the normal WT. The WT stress give continued for 3 days. Plasma levels of cortisol, glucose and lactic acid were higher in stress group than that of non-stressed group until 72 hours. However, The $Na^+,\;Cl^-$, osmolality and aspartate aminotransferase (AST) levels showed no significant differences in two groups. This results in stress group showed that goldfish exhibit "typical" physiological responses (in cortisol, glucose, lactic acid, hematocrit, red blood cell and hemoglobin) to the stress induced by WT changes.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.68-74
• /
• 2014

During the life firing test of 1 N-class thruster development model, pulse mode performance and performance changes were examined. The deviation of pulse mode response time according to thruster feed pressure was relatively small and the resultant ignition delay, response time, tail-off time were 32-35 ms, 86-91 ms, 89-98 ms, respectively. For the stabilized pulse region the impulse bit revealed the outstanding reproducibility of 1.41, 1.32, 2.10% at $3{\sigma}$. During the life firing test, the impulse bit was decreased with limited amounts, therefore the pulse mode performance could be considered to be maintained. The thrust centroid was also maintained during the life firing test.

• The Korean Journal of Pain
• /
• v.1 no.1
• /
• pp.53-58
• /
• 1988

We have treated patients who have visited pain clinic and those admitted to the other departments of Pusan National University Hospital from Mar. 1987 to Feb. 1988 with complaints of severe cancer pain on both upper and lower abdomen and extremities by continuous administration of a very small amount of morphine in the lumbar subarachnoid(group I) and epidural(group II) space in 10 cases respectively. The results of analgesia obtained are as follows: 1. The average duration in onset of analgesia was 8 mins. in group I and 23 mins. in group II. 2. The average duration In maintaining analgesia was 12.4 hrs. in group I and 18.4 hrs. in group II. 3. The efficiency of analgesia in group I was excellent in 5, good in 4, and null in 1, and group II was excellent in 5, good in 2, and moderate in 3. 4. The degree of tolerance in group I was rather mild comparable ti that of pain score 4 till the 22nd. day of morphine administration. 5. The complications are: 2 of respiratory distress in group I, 2 of voiding difficulties in both group I and II, 1 of itching sensation in both group I and II, 1 of euphoria with hallucination In group I, and 1 of C.S.F leakage in group II. As results, it is thought that epidural administration is safer than subarachnoid administration in achieving analgesia with morphine among patients with malignant pain if the problem of tolerance is solved.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.361-367
• /
• 2011

The uniaxial compressive strength (UCS) is an important factor in the design and construction of surface and underground structures. However, the method employed to measure UCS is time consuming and expensive to apply in the field. Therefore, we developed a model to estimate UCS based on a few properties using linear regression analysis, which is a statistical method. To develop the model, valid factors from the test results were selected from a correlation analysis using a statistical program, and the model was formulated by linear regression based on the relationships among factors. UCS estimates derived from the model were compared with the results of UCS tests, to assess the reliability of the model. The relationship between rock properties and UCS indicates that the factors with the greatest influence on UCS are point load strength and shape facto r. The UCS values obtained using the model are in good agreement with the results of the UCS test. Therefore, the developed model may be used to estimate the UCS of rocks in regions with similar conditions to those of the present study area.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.22-28
• /
• 2007

Using woodceramics made from sawdust board of pine thinning logs, changes in surface temperature were investigated, by the heating rate and keeping time at maximum temperature. The heating rate of $2^{\circ}C/min$ and keeping time at maximum temperature 1 hour, were the highest in surface temperature. Also, it was found that woodcermics maintained heat for a long time because the descending velocity of their surface temperature was slower than that of the heater.